CAMDEN Lazerpoint CM-TXLF Series User manual

Lazerpoint™ CM-TXLF Series
FOB Style Transmitters
Installation Instructions
Page 1 of 2
Section 1
General Description
Camden Lazerpoint™ Radio Controls comprise the following
models:
• CM-TXLF-1, CM-TXLF-2, & CM-TXLF-4 Key Fob
Transmitters, as well as;
• CM-TX-9 Wall switch ready transmitter
• CM-TX-99 Plug-in 2-Channel Transmitter
• CM-RX-91 Basic Receiver
• CM-RX-92 Full function (dual relay) Receiver.
These instructions cover the TXLF transmitters.
Camden Key Fob transmitters utilize readily available
CR-2032 Lithium batteries, and special circuitry to assure
long life. A proprietary bi-colour LED circuit is used to
annunciate wireless activation, low battery, & Battery Gas
Gauge™ conditions.
Section 2
Installation
Mounting
Camden TXLF Fobs can be attached to a key chain using the
included ring.
Fobs can also be mounted to a wheelchair by using accessory
number # CM-TXLFB Mounting Base. This unique accessory
converts any of the Mini Fobs to a full size unit which may be
clipped to a belt or sun-visor, or fastened to a desk or counter
for reception use. See our Lazerpoint™ spec sheet or TXLFB
Instruction manual for further details.
The CR-2032 battery is pre-installed in the Fob. Simply press
the button and observe the GREEN LED, which indicates
proper transmission.
Test the battery strength by pressing and holding the button
for approximately 5 seconds. The LED should ash RED
5 times, meaning the battery is at full capacity. This is the
BatteryGasGauge™feature.IftheLEDashesREDonly1-2
times, you should change the battery for a fresh (new) one.
See instructions at right.
When the battery is low and needs to be changed, the LED
willindicateaslowredash—1ashpersecond.Theunitwill
still continue to function (transmit) for a time, but the battery
should be changed as soon as possible.
Learning the Transmitter(s) to the Receiver
To learn the transmitter into an RX-91 or RX-92 receiver, press
the PB1 (or PB2) button on the Receiver using a small blunt
object such as a small blade screwdriver or similar. Within 10
seconds, press the button on the TXLF transmitter. The Green
LEDArraywillashoncetoconrmenrollment.Repeatwith
any additional transmitters. Pressing the learned transmitter
againwillsignalthereceiverthatyouarenishedprogramming
and LED’s 1 & 2 will ash, in an alternating sequence.
Pressing the transmitter a third time will activate the relay and
corresponding LED, and also the device connected to the relay
contacts.
For multiple button FOBS – TXLF-2 & TXLF-4, learn the desired
button into one receiver, and the other button(s) into additional
receivers. (You could also learn Button 1 into Channel 1 of the
RX-92, and Button 2 into Channel 2 of the same RX-92.)
Refer to the RX-91 or RX-92 receiver for further programming
instructions.
Replacing the Battery
Camden
PWA-201-0329-051
Camden
PWA-201-0329-051
Camden
PWA-201-0329-051
+
Panasonic
CR2032
3V
+
Camden
PWA-201-0329-051
Panasonic
CR2032
3V
+
1
4 5
6
7
2 3
Twist a coin in slot to
open transmitter case
Turn over the PCB
Separate 2 halves
Remove old battery
Insert new battery
Remove PCB from
bottom half
Insert PCB. Snap
the case together.

Lazerpoint™ CM-TXLF Series FOB Style Transmitters Installation Instructions
Page 2 of 2
Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control
Section 3
Technical Data
Models: TXLF-1, TXLF-2, & TXLF-4
Buttons / Channels: 1, 2, & 4 respectively.
Transmit Frequency: 902 / 915.25 / 928 MHz
(spread spectrum technology)
Codes: 1 million (20 bit) codes
Size: 2 9/16” L x 1 9/16” W x 5/8” D
(102mm x 42mm x 16mm)
LED Indicator: Used for transmit status (green),
Low Battery, and Battery Gas
Gauge™ indicator (red).
Power: 1 x CR-2032 Lithium battery
Battery life: Minimum 115,000 operations
Range: Over 250 ft (76 m) open area
Temperature rating: -40F to 185F (-40 C to +85C)
Section 4
Warranty
Camden Door Controls guarantees the CM TXLF series
transmitters to be free from manufacturing defects for
3yearsfromdateofsale.Ifduringtherst3yearsaTXLF
transmitter fails to perform correctly, it may be returned to our
factory where it will be repaired or replaced (at our discretion)
without charge. Except as stated herein, Camden extends
no warranties expressed or implied regarding function,
performance or service.
Batteries are exempt from this warranty.
Assembly Instructions
5502 Timberlea Blvd.,
Mississauga, ON Canada
L4W 2T7
www.camdencontrols.com
Toll Free: 1.877.226.3369
File: CM-TXLF Transmitter Manual.indd- Rev1
Revised: July 3rd, 2014
Part No: 40-82B160
PWA-201-0329-051
Camden
Plastic
Case FOB
Top
Assembly
Top + Bottom
Assemblies
Snap Together
Bottom
Assembly
Plastic Case
Bottom
Plastic
Buttons
Translucent
Rubber
Membrane
Circuit
Board