Campbell Hausfeld NS219001 User manual

General Safety Information
This manual contains safety, operational
and maintenance information.
Read this manual and
understand all safety
warnings and instructions
before operating the nailer.
Contact your Campbell
Hausfeld representative if
you have any questions.
CALIFORNIA PROPOSITION 65
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
OPERATOR’S RESPONSIBILITY:
Before operating the nailer, read and
understand all safety warnings and
labels. Follow the operating
instructions outlined in this manual.
EMPLOYER’S RESPONSIBILITY:
Distribute this instruction manual to all
users before allowing use of the nailer.
Ensure all operators read, understand
and follow all safety warnings, labels and
instructions outlined in this manual.
Danger
indicates
an imminently hazardous situation
which, if not avoided, WILL result in
death or serious injury.
 Do not use any type
of flammable gases or
oxygen as a power
source for the nailer.
Use filtered,
lubricated, regulated
compressed air only. Use of a
compressed gas instead of
compressed air may cause the nailer
to explode which will cause death or
serious personal injury.
Do not exceed
maximum operating
pressure of the nailer
(120 psi). The nailer
will not function
properly. Do not use a
compressed air source capable of
more than 200 psi. The nailer could
explode which will cause death or
serious personal injury.
Never use gasoline or
other flammable
liquids to clean the
nailer. Never use the
nailer in the presence
of flammable liquids or gases. Vapors
could ignite by a spark and cause an
explosion which will result in death
or serious personal injury.
Always remain in a
firmly balanced
position when
using or handling
the nailer.
Do not modify or
disable the Work
Contact Element
(WCE). Do not tie
or tape the WCE
or trigger in a
depressed
position. Death or serious personal
injury could result.
Operating Instructions Models NS219001, NS219500, NS319001 & NS349001
Do not touch
the trigger
unless driving
nails. Never
attach air line
to nailer or
carry nailer
while touching
the trigger. The
tool could eject a fastener which
will result in death or serious
personal injury.
Warning
indicates
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
Always
disconnect
nailer from air
line before
clearing jams,
adjusting or
servicing the
nailer, relocating the nailer, or
when the nailer is not in use.
Always reconnect the air line
BEFORE loading any fasteners.
Framing Nailer
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death and/or
property damage! Retain instructions for future reference.
IN715702AV 2/08
Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American National
Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2008 Campbell Hausfeld / Scott Fetzer
Table Of Contents
General Safety . . . . . . . . . . . . 1-2
Specifications . . . . . . . . . . . . . . 2
Operating The Nailer . . . . . . . . 3
Operational Modes. . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . 7
Fasteners . . . . . . . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . . . . . . 8
Description
This nailer is designed for framing,
trusses, sub-floors, sheathing, exterior
decks, and pallet/create assembly.
Features include: convenient top loading
magazine, no-mar tip, adjustable
exhaust, single cycle trigger, and an
adjustable depth of drive mechanism.
MANUAL

OCO
2
120 psi
MAX.
Locate model and date code
on tool and record below:
Model No. ________________________
Date Code ________________________
Retain these numbers for
future reference.
For parts, product & service information
visit www.chpower.com
See Warranty on page 8 for important information about commercial use of this product.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.

2
The nailer could eject a fastener
causing death or serious personal
injury.
Protect your eyes
and ears. Wear Z87
safety glasses, with
side shields. Wear
hearing protection.
Employers and users are
responsible for ensuring the user or
anyone near the nailer wears this
safety protection. Serious eye
injury or permanent hearing loss
could result.
Do not use a
check valve or
any other
fitting which
allows air to
remain in the
nailer. Death or
serious personal injury could occur.
Never place
hands or any
other body
parts in the nail
discharge area
of the nailer.
The nailer might
eject a fastener and could result in
death or serious personal injury.
Never carry the
nailer by the air
hose or pull the
hose to move
the nailer or a
compressor. Keep
hoses away from
heat, oil and sharp edges. Replace
any hose that is damaged, weak or
worn. Personal injury or tool
damage could occur.
Always assume the nailer contains
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Never point the
nailer at anyone. Accidental
triggering of the nailer could result
in death or serious personal injury.
Do not drive a
nail on top of
other nails. The
nail could glance
and cause death
or a serious
puncture wound.
Do not operate
or allow anyone
else to operate
the nailer if any
warnings or
warning labels
are not legible.
Warnings or warning labels are located
on the nailer magazine and body.
Never leave the nailer unattended or
connected to an air compressor when
not in use. Serious personal injury
can occur if someone picks up and
uses the nailer without knowing the
correct way to operate the nailer.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Caution
indicates
a potentially hazardous situation which,
if not avoided, MAY result in minor or
moderate injury.
Do not modify or alter the nailer or
any nailer parts. Do not use the nailer
if any shields or guards are removed
or altered. Do not use the nailer as a
hammer. Personal injury or tool
damage may occur.
 Avoid long extended periods of work
with the nailer. Stop using the nailer
if you feel pain in hands or arms.
Always
check that
the Work
Contact
Element
(WCE) is
operating
properly. A
nail could
accidentally
be driven if the WCE is not working
properly. Personal injury may occur
(See "Checking the Work Contact
Element" Section).
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
Notice
indicates
important information, that if not
followed, may cause damage to
equipment.
Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Air compressors providing air to the
nailer should follow the
requirements established by the
American National Standards
Institute Standard B19.3-1991;
Safety Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Operating Instructions
!WARNING
NS319001
NS219001 NS219500 NS349001
• REQUIRES
(SCFM with 16 nails 4.1 4.1 4.1
per minute @ 90 psi)
• AIR INLET 1/4” NPT 1/4” NPT 1/4” NPT
• NAIL LENGTH 2” to 2” to 2” to
RANGE 31⁄2”3
1⁄2”3 1⁄2”
• NAIL SHANK 0.113” to 0.113” to 0.113” to
RANGE 0.131” 0.131” 0.131”
• MAGAZINE
CAPACITY 60-75 60-75 75-105
• WEIGHT 9 lbs 3 oz 7 lbs 6 oz 9 lbs 2 oz
• LENGTH 19.25” 19.25” 18.50”
• HEIGHT 15.25” 15.25” 15.00”
• MAX. PRESSURE 120 psi 120 psi 120 psi
• PRESSURE RANGE 70 - 120 psi 70 - 120 psi 70 - 120 psi
Nailer Components And Specifications Adjustable Direction Exhaust Deflector
Nail Loading Area
Magazine
Trigger
Warning Labels
(Backside)
Nail Discharge Area
Work Contact Element
www.chpower.com
Debris Shield

3
Operating The Nailer
Read this manual and understand all
safety warnings and instructions before
operating the nailer.
LUBRICATION
This nailer requires lubrication before
using the nailer for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis.
The work
surface
can become damaged by excessive
lubrication. Proper lubrication is the
owner’s responsibil- ity. Failure to
lubricate the nailer properly will
dramatically shorten the life of the nailer
and void your warranty.
1. Disconnect
the air
supply from
the nailer
to add
lubricant.
2. Turn the nailer
so the air inlet
is facing up.
Place 4-5 drops
of 30 W non-
detergent oil
into air inlet.
Do not use
detergent oils, oil additives, or air
tool oils. Air tool oils contain
solvents which will damage the
nailer’s internal components.
3. After adding oil,
run nailer briefly.
Wipe off any
excess oil from
the cap exhaust.
REMOVING NO-MAR DECKING TIP
1. Disconnect air
supply from
nailer.
2. Remove all fasteners from magazine
(See UNLOADING THE
NAILER).
3. Remove no-mar tip retaining ring.
4. Pry no-
mar tip
away
from the
work
contact
element.
5. Replace
retaining
ring onto
no-mar
tip, then
store tip
in safe
place for future use.
INSTALLING NO-MAR DECKING TIP
1. Disconnect air
supply from
nailer.
2. Remove all fasteners from magazine
(See UNLOADING THE NAILER).
3. Remove retaining ring from no-mar
tip.
RECOMMENDED HOOKUP
1. The air
compressor
must be able
to maintain a
minimum of 70
psi when the nailer is being used.
An inadequate air supply can cause
a loss of power and inconsistent
driving.
2. An oiler can be
used to provide oil
circulation through
the nailer. A filter
can be used to
remove liquid and
solid impurities which can rust or
“gum up” internal parts of the
nailer.
3. Use 3/8” air
hoses with a
minimum
working
pressure of 150 psi. Use 1/2” air
hoses for 50’ run or longer. For
better performance, install a 3/8”
quick plug (1/4” NPT threads) with
an inside diameter of .315” (8mm)
on the nailer and a 3/8” quick
coupler on the air hose.
4. Use a pressure regulator on the
compressor, with an operating
pressure of 0 - 125 psi. A pressure
regulator is required to control the
operating pressure of the nailer
between 70 and 120 psi.
NO-MAR DECKING TIP
The no-mar decking tip is designed to
eliminate marks caused by the serrated
work contact element (WCE). The no-
mar tip may be removed if not
required (See REMOVING NO-MAR
DECKING TIP). Use tool in single cycle
mode (SEE OPERATIONAL MODES)
when no-mar tip is in place.

70 psi
Min.
OIL
120 psi
Max.
Models NS219001, NS219500, NS319001 & NS349001
Retaining
Ring
No-Mar Tip
Work
Contact
Element
No-
Mar
Tip
Recommended Hookup
Quick
Coupler
Air
Hose
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Oiler
Regulator
Filter
Quick
Plug
www.chpower.com

4. Carefully
place no-
mar tip
over the
end of
work
contact
element.
Position
tip onto
WCE
making certain serrated gooves on
each piece are in line and fit snugly
together.
5. Position
retaining
ring on no-
mar tip and
press firmly
in place.
6. Check
that the
WCE and
trigger
move up
and down
freely
without
sticking or
binding.
Operational Modes
Always
know the
operational mode of the nailer before
using. Failure to know the operational
mode could result in death or serious
personal injury.
This stick framing nailer may be
operated in the “Single Cycle” or the
“Bottom Trip” mode. The nailer is
delivered in the single cycle mode. A
separate ‘red’ trigger for “Bottom
Trip” mode is included with tool as an
accessory.
SINGLE CYCLE MODE
When the black trigger is installed,
nailer is in single cycle mode. This
method is recommended when precise
nail placement is required. Operation
in this mode requires trigger to be
pulled each time a nail is driven. Nailer
can be actuated by depressing the
Work Contact Element (WCE) against
work surface followed by pulling the
trigger.
The trigger must be released after each
fastener is driven to allow tool to reset.
Since the tool can only be actuated by
first removing the finger from the
trigger, this is considered to be a more
restrictive mode of operation, suitable
for less experienced users.
WORK CONTACT ELEMENT (WCE)
Check
the
operation of the Work Contact Element
(WCE) trip mechanism before each use.
The WCE must move freely without
binding through its entire travel
distance. The WCE spring must return
the WCE to its fully extended position
after being depressed. Do not operate
the nailer if the WCE trip mechanism is
not operating properly. Personal injury
may occur.
1. Disconnect
the air
supply
from the
nailer.
2. Remove all
nails from the
magazine
(see
Unloading
The Nailer).
3.
Make
sure the
trigger
and work
contact
element
(WCE)
move
freely up
and
down without sticking or binding.
4. Reconnect
air supply to
the nailer.
5. Depress the
Work
Contact
Element
(WCE)
against the
work surface
without
pulling the
trigger. The
nailer MUST NOT OPERATE. Do not
use the tool if it operates without
pulling the trigger. Personal injury
may result.
BOTTOM TRIP MODE
When the red trigger is installed, the
nailer is in bottom trip mode. This
method is recommended when less
precise nail placement is required.
Operation in this mode requires trigger
to be depressed with nailer off of the
work surface. Then, the nose of the
nailer is tapped against the work
surface causing a nail to be driven.
Each time the Work Contact Element is
depressed, a nail is driven into the work
surface. Extreme care should be taken
because a nail will be driven when the
WCE is pressed against any surface.
Since the tool can be actuated without
removing the finger from the trigger,
this is considered to be a less restrictive
mode, suitable for more experienced
users.
MODE CONVERSION
To convert the tool from one mode to
the other:
1. Remove o-ring on the side of
trigger pin.
2. Remove trigger pin, trigger, and
trigger spring.
3. Switch out only the trigger.
4. Replace trigger spring, trigger,
trigger pin, and o-ring.
Do not attempt to modify the trigger
components in any manner and do not
attempt to use any other trigger
components other than those intended
for this tool.
Contact your Campbell Hausfeld
representative if you have any
questions.
Operating Instructions
4
Grooves
www.chpower.com
Mode Conversion
Trigger spring
O-ring
Trigger pin
Trigger

6. Remove
nailer from
work
surface. The
Work
Contact
Element
(WCE) must
return to its
original
down position. Pull the trigger. The
nailer MUST NOT OPERATE. Do not
use the tool if it operates while
lifted from the work surface.
Personal injury may result.
7. Pull the trigger and depress the
work contact element (WCE) against
the work surface. The nailer MUST
OPERATE.
8. Depress the Work Contact Element
(WCE) against work surface. Pull the
trigger. The nailer MUST OPERATE.
LOADING THE NAILER
1. Always connect the tool to the air
supply before loading fasteners.
2. Pull nail
pusher
mechanism
back until
pusher
engages
with
magazine
latch.
3. Load strips
of fasteners
into the
magazine
slot. Make
sure that
the nails
are placed
into tool at the proper orientation.
4. Squeeze
the pusher
and the
latch
together to
unlatch
pusher.
Make sure
the head of the last nail is under the
head of the pusher.
UNLOADING THE NAILER
1. Always unload all fasteners before
removing tool from service.
Unloading is the reverse of loading,
except always disconnect the air
hose before unloading.
2. Pull nail
pusher
mechanism
back until
pusher
engages
with
magazine
latch.
3. Hold tool
upright so
nails will
slide
backwards
toward
magazine
slot.
4. Squeeze
the pusher
and latch
together to
unlatch the
pusher
once all
nails have
been removed.
ADJUSTING THE NAIL PENETRATION
The NS219001, NS319001 and NS349001
nailers are equipped with an adjustable
depth of drive feature. This allows the user
to determine how deep a fastener will be
driven into the work surface.
1. Adjust the operating pressure to a
pressure which will consistently
drive the fasteners. Do not exceed
the maximum operating pressure of
the nailer of 120 psi.
2. To adjust the depth-of-drive, loosen
the 4mm bolt on the top of nose. To
increase depth, push WCE in toward
nose as much as desired. Re-tighten
bolt. To decrease depth, pull WCE
out as much as desired. Re-tighten
bolt.
3. Make sure that the trigger and work
contact element (WCE) move freely
up and down without binding or
sticking after each adjustment.
ANTI-DRY FIRE
These tools are equipped with an Anti-Dry
Fire feature. This prevents the WCE from
being pushed in when only a few nails
remain. Simply load new nail clip behind
remaining nails to continue shooting.
ADJUSTING THE DIRECTION OF THE
EXHAUST
The nailers are
equipped with
an adjustable
direction
exhaust
deflector. This
is intended to
allow the user to change the direction
of the exhaust. Simply twist the
deflector to any direction desired.
CLEARING A JAM FROM THE NAILER
1. Disconnect
nailer from
air supply.
Models NS219001, NS219500, NS319001 & NS349001
5
Rotate
Nail pusher
mechanism Latch
Nail pusher
mechanism
Latch
12
12
www.chpower.com

6
Operating Instructions
www.chpower.com
2. Remove all
nails from
the
magazine
(see Loading/
Unloading).
Failure to do
so will cause
the nails to
eject from
the front of
the tool.
3. Insert a
screw-
driver
into the
nose of
the tool.
Push up
on the driver blade to free the
jammed nail.
4. Grab the
jammed
nail with
pliers
and
remove.
Technical Support
Please call our Nailer Hotline at 1-800-
543-6400 with any questions regarding
the operation or repair of this nailer or
for additional copies of this manual.
Fastener And Replacement
Parts
Use only
genuine
Campbell Hausfeld fasteners (or
equivalent - see Fastener Interchange
Information). Use only genuine
Campbell Hausfeld replacement parts.
Never substitute parts. Do not use
modified parts or parts which will not
give equivalent performance to the
original equipment. Tool performance,
safety and durability could be reduced.
When ordering replacement parts or
fasteners, specify by part number.
Nailer Repair
Nailer repairs must be performed by
qualified and experienced service
people ONLY.
Assembly Procedure For Seals
When repairing a nailer, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots. After
reassembling, a few drops of 30W non-
detergent oil, or equivalent, must be
added through the air line before
testing.

Models NS219001, NS219500, NS319001 & NS349001
7
Fasteners
NS219001 and NS219500 Tools will also drive fasteners designed for: Sears 18465, Porter Cable FR350, Hitachi NR83A, and Senco
FramePro 702XP, 752XP, Ridgid R350RHA, and DeWalt D51844, D51845.
NS349001 and NS319001 Tools will also drive fasteners designed for: Porter Cable FC 350A, Hitachi NR83AA2, Senco FramePro
701XP, 751XP , Ridgid R350CHA, DeWalt D51822, D51823, and Paslode F-3505.
Air leaking at trigger valve
Air leaking between
housing and nose
Air leaking between
housing and cap
Nailer skips driving nail
Nailer runs slow or has loss
of power
Nails are jammed in nailer
O-Rings in trigger valve housing are
damaged
Loose screws in housing
Damaged O-Rings
Damage to bumper
Loose screws
Damaged gasket
Worn bumper
Dirt in nose piece
Dirt or damage prevent nails or pusher
from moving freely in magazine
Damaged pusher spring
Inadequate air flow to nailer
Worn O-Ring on piston or lack of
lubrication
Damaged O-Ring on trigger valve
Air leaks
Cap gasket leaking
Nailer not lubricated sufficiently
Broken spring in cylinder cap
Exhaust port in cap is blocked
Guide on driver is worn
Nails are not correct size
Nails are bent
Magazine or nose screws are loose
Driver is damaged
Replace O-Rings. Check operation of Work
Contact Element (WCE)
Tighten screws
Replace O-Rings
Replace bumper
Tighten screws
Replace gasket
Replace bumper
Clean drive channel
Clean magazine
Replace spring
Check fitting, hose or compressor
Replace and lubricate O-Rings
Replace O-Rings
Tighten screws and fittings
Replace gasket
Lubricate nailer
Replace spring
Replace damaged internal parts
Replace guide
Use only recommended nails
Replace with undamaged nails
Tighten screws
Replace driver
Troubleshooting Guide
Stop using nailer immediately if any of the following problems occur. Serious personal injury
could result. Any repairs or replacements must be done by a Qualified Service Person or
Authorized Service Center.
Problem Cause Solution
www.chpower.com

Operating Instructions
8
www.chpower.com
Limited Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: – One (1) Year.
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,
Harrison, Ohio, 45030, Telephone: [phone]
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the
Campbell Hausfeld product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun,
inflator or air accessory supplied or manufactured by Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the
duration of the warranty period.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial,
industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States
do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance
with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or
failure to operate products in accordance with instructions shall also include the removal or alteration of any safety
devices. If such safety devices are removed or altered, this warranty is void.
D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.
E. Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields,
driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants,
material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters,
collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other
expendable part not specifically listed. These items will only be covered for ninety (90) days from date of original
purchase. Underlined items are warranted for defects in material and workmanship only.
F. Cosmetic defects that do not interfere with the product’s function.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or
components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Call Campbell Hausfeld (800-543-6400) to obtain your warranty service options. Freight costs must be borne by the
purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be
scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability
of replacement parts.
This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may
also have other rights which vary from state to state or country to country.

RESPONSABILITÉ DE L’EMPLOYEUR
Ce manuel d’instruction doit être mis à
la disposition de tous les utilisateurs
avant qu’ils ne se servent de la cloueuse.
S’assurer que tous les utilisateurs lisent
et comprennent parfaitement les
notices de sécurité, étiquettes et
instructions décrites dans ce manuel.
Danger
indique
une situation hasardeuse imminente
qui RÉSULTERA en perte de vie ou
blessures graves.
Ne pas utiliser un gaz
inflammable ni
l’oxygène pour
alimenter la cloueuse.
Utilisez seulement de
l’air comprimé filtré,
lubrifié et réglé.
L’utilisation d’un gaz comprimé au
lieu de l’air comprimé peut faire
exploser la cloueuse et entraîner des
blessures graves ou mortelles.
Ne pas dépasser la
pression de service
maximale de la
cloueuse (827 kPa).
La cloueuse ne
fonctionnera pas
correctement. Ne pas
utiliser une source
d’air comprimé qui a une capacité de
plus que 1379 kPa. La cloueuse
pourrait exploser et causer des
blessures graves ou mortelles.
Ne jamais utiliser de
l’essence ni les fluides
inflammables pour le
nettoyage de la cloueuse.
Ne jamais utiliser la cloueuse près d’un
liquide ou gaz inflammable. Une
étincelle peut allumer les vapeurs et
causer une explosion qui peut résulter
en perte de vie ou blessures graves
personnelles.
Toujours bien s’équilibrer
pendant la manipulation
ou l’utilisation de la
cloueuse.
Ne jamais modifier ou
empêcher le
fonctionnement du
mécanisme de
déclenchement par
contact (WCE) et ne
Généralités Sur La Sécurité
Ce manuel contient des informations
concernant la sécurité, le
fonctionnement et l’entretien.
Lire attentivement ce manuel
et comprendre tous les
avertissements de sécurité et
les instructions avant
d’utiliser la cloueuse. Si vous
avez des questions, contacter un
représentant de Campbell Hausfeld.
PROPOSITION 65 CALIFORNIE
Vous pouvez créer de la
poussière en coupant,
ponçant, perçant ou meulant
les matériaux tels que le bois, la
peinture, le métal, le béton, le ciment
ou autre maçonnerie. Cette poussière
contient souvent des produits
chimiques reconnus pour causer le
cancer, les déformations congénitales
ou autres problèmes de la reproduction.
Portez de l’équipement de protection.
RESPONSABILITÉ DE L’UTILISATEUR
Avant d’utiliser cette cloueuse, prendre
connaissance de tous les avertissements
et des étiquettes concernant la sécurité.
Suivre les instructions données dans ce
manuel.
jamais maintenir la gâchette
enfoncée à l’aide de ruban adhésif
par exemple. Ceci pourrait entraîner
des blessures graves ou mortelles.
Ne toucher à la
gâchette qu’au
moment de poser des
clous. Ne jamais
actionner la gâchette
durant le transport de
la cloueuse ou durant
le raccordement de celle-ci au tuyau
d’air comprimé. L’éjection
accidentelle d’un clou peut causer
des blessures graves ou mortelles.
Avertissment indique une situation
hasardeuse potentielle qui PEUT résulter
en perte de vie ou blessures graves.
 Toujours
débrancher le
tuyau d’air
comprimé de la
cloueuse avant
de dégager un
clou bloqué, de
régler, de réparer ou de transporter la
cloueuse ou lorsque celle-ci n’est pas en
service. Le raccordement du tuyau d’air
comprimé doit toujours s’effectuer
AVANT le chargement du magasin.
L’éjection accidentelle d’un clou peut
causer des blessures graves ou mortelles.
IN715702AV 2/08
Les Cloueuses Campbell Hausfeld conforment aux/ou dépassent les standards de l’American
National Standard/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2008 Campbell Hausfeld / Scott Fetzer
Description
Cette cloueuse est conçue pour la
charpenterie, les armatures, les
sousplanchers, le revêtement, les terrasses
extérieures et les montages de palette/
caisse à claire-voie. Les caractéristiques
comprennent un chargeur du haut
pratique, une buse non-gâcheuse,
échappement orientable, gâchette à
cycle unique et un mécanisme de contrôle
de profondeur d’enfoncement.
MANUAL

827 kPa
Max.
Table Des Matières
Directives De Sécurité . . . . . . . 9-10
Spécifications . . . . . . . . . . . . . . 10
Fonctionnement De La Cloueuse 11
Modes De Fonctionnement . . . . 12
Attaches . . . . . . . . . . . . . . . . . . 14
Guide De Dépannage . . . . . . . . 15
Garantie . . . . . . . . . . . . . . . . . . 16
OCO
2
Trouver le modèle et le code de date sur
l’outil et les inscrire plus bas.
N° de modèle ____________________
Code de date ______________________
Conserver ces numéros
comme référence.
Instructions D’Utilisation Modèles NS219001, NS219500, NS319001 et NS349001
Cloueuse à Charpente
S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit
décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!
Conserver ces instructions comme référence.
Voir la Garantie à la page 16 pour de l’information importante sur l’utilisation commercial de ce produit.
MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!
Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.

 Protéger vos yeux avec
des lunettes de sécurité
Z87 à écrans latéraux et
vos oreilles avec un
protecteur auditif. Le
patron et l’utilisateur
sont responsables pour assurer que
l’utilisateur et ceux à proximité de la
cloueuse portent l’équipement de
securite, sinon, il y a risque de blessures
graves oculaires ou de dommage
permanent a l’ouie. sécurité, sinon, il y
a risque de blessures graves oculaires
l’équipement de sécurité, sinon, il y a
risque de blessures graves oculaires ou
de dommage permanent à l’ouie.
sécurité, sinon, il y a risque de blessures
graves oculaires ou de dommage
permanent à l’ouïe.
 Ne pas utiliser
un clapet ni
autre raccord
qui permet que
l’air reste dans
la cloueuse. Cela
peut entraîner
des blessures graves ou mortelles.
Ne jamais poser
l’embout de
clouage sur la
main ou sur toute
autre partie du
corps. L’éjection
accidentelle d’un
clou peut causer des blessures
graves ou mortelles.
Ne jamais
transporter la
cloueuse par le
tuyau à air. Ne
jamais tirer sur le
tuyau pour
déplacer la
cloueuse ou le compresseur. Garder
le tuyau à air à l’écart de la chaleur,
l’huile et les objets pointus.
10 Fr
Remplacer les tuyaux endommagés,
faibles ou usés. Sinon, il y a risque
de blessures personnelles ou de
dommage à l’outil.
Toujours présumer que la cloueuse
contient des clous. Ne jamais traiter
la cloueuse de jouet. Toujours tenir
les autres personnes à l’écart de
l’endroit de travaille en cas
d’expulsion accidentelle. Ne jamais
diriger la cloueuse vers une autre
personne. Le déclenchement
accidentel de la cloueuse peut
causer la mort ou blessures graves.

Ne jamais enfoncer
les clous un par
dessus l’autre. Le
clou pourrait
ricocher et causer
la mort ou une
blessure grave de
perforation.
Ne pas utiliser
la cloueuse/ni
permettre
qu’une autre
personne
l’utilise si les
avertissements
ou les étiquettes d’avertissement
situés sur le chargeur et corps de la
cloueuse ne sont pas lisables.
Ne jamais laisser la cloueuse sans
surveillance ni branchée à un
compresseur si hors-service. Il y a
risque de blessures graves si la
cloueuse est utilisée par une
personne qui ne connait pas les
instructions d’utilisation.
Ne pas échapper ni jeter l’outil car ceci
peut causer du dommage le rendant
dangereux à utiliser. Si l’outil s’est fait
échappé ou jeté, l’examiner
soigneusement afin de déterminer s’il
est courbé, fendu ou s’il y a des fuites
ou pièces détachées endommagées.
ARRËTER et réparer avant d’uitliser ,
sinon, il y a risque de blessures graves.
Attention
indique
une situation hasardeuse potentielle
qui PEUT résulter en blessures.
Ne pas modifier ni altérer la
cloueuse ou ces pièces. N’utilisez pas
une cloueuse si les écrans ou
protecteurs ont été enlevés ou
altérés. Cela peut entraîner des
blessures ou endommager l’appareil.
Éviter d’utiliser la cloueuse pour une
période de temps prolongée. Cesser
d’utiliser la cloueuse si l’on ressent
des douleurs dans les mains ou dans
les bras.
Toujours vérifier
le bon
fonctionnement
du mécanisme de
déclenchement
par contact
(WCE). L’éjection
accidentelle de
clou peut se
produire si ce mécanisme ne
fonctionne pas correctement et cela
pourrait entraîner des blessures. (Voir
“Vérification du mécanisme de
déclenchement par contact”).
Pour éviter l’expulsion d’une attache,
débrancher la source d’air et relâcher
la tension du poussoir avant de
procéder au déblocage. Sinon, il y a
risque de blessures graves.
Avis
indique
de l’information importante pour éviter
le dommage de l’équipement.
Éviter d’utiliser la cloueuse lorsque
le chargeur est vide. Sinon, il y a
risque d’usure accéléré de l’outil.
Instructions D’Utilisation
!AVERTISSEMENT
Pièces Détachées Et Spécifications De La Cloueuse Déflecteur de direction
d’échappement réglable Endroit de
chargement de clous
Chargeur
Gâchette
Décalcomanies de sécurité
(arrière)
Endroit d’expulsion de clous
Mécanisme de déclenchement
par contact
Écran de débris
NS319001
NS219001 NS219500 NS349001
•REQUIERT
(m /min avec 0,12 0,12 0,12
16 clous par minute
@ 621 kPa)
•ARRIVÉE D’AIR 1/4 po NPT 1/4 po NPT 1/4 po NPT
•GAMME DE 2 po - 2 po - 2 po -
LONGUEUR 31⁄2 po 31⁄2 po 31⁄2 po
DE CLOUS
• GAMME DE TIGES 0.113 po - 0.113 po - 0.113 po -
DE CLOUS 0.131 po 0.131 po 0.131 po
• CAPACITÉ DU
CHARGEUR 60-75 60-75 75-105
• POIDS 4,17 kg 3,35 kg 4,14 kg
• LONGUEUR 48,90 cm 48,90 cm 46,99 cm
• HAUTEUR 38,74 cm 38,74 cm 38,10 cm
• PRESSION MAX. 827 kPa 827 kPa 827 kPa
• GAMME DE 483-827 kPa 483-827 kPa 483-827 kPa
PRESSION