CAMXTOOL I-X-21 F User manual

OXYGEN INJECTOR
USER MANUAL

Content
Product introduction --------------------------------------01
Product parameters -------------------------------------- 02
Product features ------------------------------------------ 02
Instructions ------------------------------------------------- 03
Precautions ------------------------------------------------ 04
Troubleshooting ------------------------------------------- 04
Product maintenance ------------------------------------ 05
Disposal of waste batteries ---------------------------- 05

Product introduction
1. Power 5. Type-c charging cable
2. Spray Button 6. Nozzle
3. Charging port 7. Tight needle nut
(adjust the amount of mist)
4. Spray gun 8. Essence bottle
9. Indicator light
⑤

Product parameters
Item Oxygen Injector
Product
model
I-X-21 F Product
Net Weight
About
300g
Input
Voltage：5V Input Power：5W
Charging
Time：<2 hours Battery
Capacity：850mAh
Product
Size：
42*145*125
mm Use time：About 60mins
Product features
A. A technique that awakens the skin by injecting oxygen
into the skin's muscular base
Different from the traditional hand-beating mode, the water
and nutrients are penetrated into the basal layer of the skin
through pressure to achieve the effect of skin moisturizing
as before.
B.Nano hydrating improves skin texture
Conventional replenishment can only stay on the surface of
the skin, that is, the cuticle, which cannot penetrate the cell
membrane, resulting in skin chronically dry and tight.
Oxygen injector adopts nano-level technology to
decompose water molecules into micron molecules, and
with a light spray, the whole face can enjoy the surging and
full of water.
C.To unclog the skin's water absorption channels by high
pressure
The water oxygen meter is equivalent to a small pressure
gun.Oxygen injection makes the pores no longer
accumulate grease, fills the skin with water, and the pores
and dirt naturally cannot stand, which greatly improves the
absorption of nutrients.

Instructions
Step 1
Put the applicable medium into
the hydrating bottle, the operating
medium is mainly water, and the
applicable medium: essence,
Sk-II water, pure dew, normal
saline, toner, etc. If it is a viscous
liquid, it must be diluted with
distilled water/purified
water/mineral water before use.
Step 2
Press the switch key to turn on
the machine, and the machine
starts to work.
Step 3
Then press the spray button for
skincare.It is recommended to
introduce the essence into energy
water/physiological saline 3 times
a week and use it every day. By
the way, adjust the tight needle
nut (adjust the size of the mist)
Step 4
Gently swipe 8-10 cm away from
the face,
Enjoy surging plump hydration all
over your face.
Open the essence bottle,
Infused with toner, essence
Press the switch
Swing this button back and
forth to spray water mist and
adjust the size of the mist
Spray mouth and spray on
face

1. Before the first use, please inject warm water/alcohol
into the water bottle to clean the inner wall of the gun.
After cleaning, inject clean water and shoot, keep it 2 to 3
times. After the clean water is emptied, empty it and air dries
the internal pipes.
2. The products used by the spray gun must be
water-soluble products (products with high concentration and
strong viscosity must be diluted with mineral water/purified
water before use).
3. Every time change the liquid in the replenishment
bottle/spray gun has not been used for a long time, please
follow the steps in point 1.
4. The liquid in the spray gun should not stay for a long time,
and the liquid will not be left after the same injection. (Avoid
blockage/leakage due to prolonged liquid retention in the
refill bottle and spray gun.
5. When using the spray gun for the first time, please use it
after fully charging. (The red light of the machine is flashing
when charging, and it is always on when fully charged)
6. The machine cannot be used when charging, and the
machine can be used normally only after unplugging the
power supply.
7. Please use a qualified power adapter with an output of
more than 5V-IA for charging.
8. Low battery reminder function, when the product has no
battery, the battery icon flashes five times to shut down.
Troubleshooting
If the liquid does not come out smoothly, please check
whether the following problems occur:
1. If the nozzle is not screwed in place, the liquid that comes
out of the spray gun mouth cannot be misted or not sprayed.
PrecautionsPrecautions

2. The "tight needle nut" at the rear of the spray gun is too
tight, and the tight needle nut can adjust the size of the mis
3. The concentration/viscosity of the liquid in the
replenishment bottle is too high (please dilute it before use)
and the spray gun is dirty, please use lukewarm water to
dredge the spray gun first.
Product Maintenance
1. After using concentrated and viscous liquids, it is
recommended to use warm water/alcohol to clean the inner
wall of the gun. After cleaning, inject clean water to clean i
2 to 3 times. After the clean water is emptied, empty it and
air dries the internal pipes.
2. Do not wipe the surface of the product with volatile liquids
(such as alcohol).
3. It is recommended to use a soft flannel to wipe. If you
don’t use it for a long time, please clean the refill bottle and
tut gun in time to prevent blockage/leakage in the refill bottle
and spray gun.
Disposal of batteries
1. When the oxygen injector reaches its service life, it shal
comply with the laws and regulations of the country or
region where it is located. The internal battery may need to
be removed, if the battery cannot be removed, please take
the product to a government-designated recycling center.
2. Do not disassemble this product unless you want to
dispose of it. Premature disassembly will damage the
product. Follow basic safety precautions and disconnect the
power supply before removing the battery.
3. Before removing the battery, make sure that the battery
has been exhausted. If the battery needs to be exhausted,
you can turn it on and work until it automatically shuts down.
4. To properly recycle or dispose of the battery, please ask
the recycling center designated by the local government

whether other parts of the oxygen injector are recycled.
5. Be careful not to short-circuit the positive and negative
poles of the battery. After removing the battery, do not turn
on the product again.
After shutdown and power off, remove the
bottom cover and take out the battery