Canarm DUAL MOUNT series User manual

I
IN NS ST
TA
AL
LL LA AT TI
IO
ON NI IN
NS
ST TR
RU
UC
CT
TI
IO
ON
NS
S
DUAL MOUNT SERIES
QUESTIONS OR CONCERNS CONTACT AT:
1-800-265-1833 (English)
1-800-567-2513 (French)
Monday through Friday 8:00 a.m. to 5:00 p.m. E.S.T.
2157 Parkedale Ave.,
Brockville, Ontario
K6V 5V6
PH: [phone]
FX: [phone]
2555 Rue Bernard
Lefebvre, Laval, Quebec
H7C 0A5
PH: [phone]
FX: [phone]
NOTE: FOR OPTIMUM QUIETNESS, FULLY ASSEMBLE FAN AND RUN 24 HOURS
!
TOOLS AND MATERIALS REQUIRED
- Philips Screw Driver
- Blade Screw Driver
- Step Ladder
- Wire Cutters
- Wiring supplies as required by electrical code.
Pg. #12
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
INSTALLATION AND WIRING TO BE IN ACCORDANCE WITH CEC,
NEC, LOCAL ELECTRICAL CODES and ANSI/NFPA 70.
Consult a qualified electrician if you are not familiar with wiring.
CF-18
LED
12/16
“Thank you” for purchasing our product. It is our policy to furnish you with high quality
products at a fair price. With proper installation your fan should provide you with years of
money saving comfort.
This fan is guaranteed to be free from defects in workmanship and Material for a period
of twenty (20) years from date of purchase. Within the first (1) year from date of purchase any
defective product should be returned to your RETAIL OUTLET along with proof of purchase.
For the balance of the warranty, nineteen (19) years, the MOTOR WINDINGS ONLY shall be
free of defects. We will correct such defects or replace the motor assembly at our option if the
product is returned, FREIGHT PREPAID, to us. The returned fan must be accompanied by
your proof of purchase and a cheque for $20.00 for handling and labour charges.
All costs of removing and re-installing the product are YOUR RESPONSIBILITY damage
to any part assuch by accident, misuse, improper installation or by affixing any accessories IS
NOT covered by this warranty. As a result of varying climatic conditions in our area this
warranty does not cover any changes in finishes, including rusting, pitting, corroding, tarnishing
or peeling.
WARRANTY VOID: In cases of alteration, abuse, installation not in accordance with
instructions or REMOVAL Of the c.S.A. Sticker.
20 YEAR LIMITED WARRANTY
11/16

Pg. #11
Pg. #2
WARNING
- To reduce the risk of fire or electrical shock, ONLY use model CQ002
remote control for optional remote control adaptability.
- To reduce the risk of personal injury DO NOT bend the blade brackets
when installing the brackets, balancing the blades or cleaning the fan. Also,
DO NOT insert foreign objects in between rotating fan blades.
- Mount with the lowest moving parts at least 2.10 Meters (7 Feet) above
floor or grade level.
-DO NOT operate reversing switch while fan blades are in motion. Fan must
be turned off and rotating blades stopped, reverse chain pulled, the speed
chain pulled again to start in the opposite direction.
INSTRUCTIONS
A ceiling fan has a completely internal switching system for total operation by
way of
pull chains. On a fan/light combination, pull chains will exist: One for light,
on and
off. The second is for fan speeds. This will be marked (SPEED) on the fan
switch housing.
1st Pull will give fan High Speed
2nd Pull will give fan Medium Speed
3rd Pull will give fan Low Speed
4th Pull will Shut Fan Off
The third pull chain is for Forward/Reverse#( Note: Some models come with a slide
switch instead of a pull chain). This setting would usually be changed twice per
year. Downdraft in summer to create a wind chill to give a cooling effect. Updraft
in winter to circulate the hot stratified air off the ceiling and back down to the floor
without creating a wind chill.
SAFETY PRECAUTIONS
1. Turn off power at main electrical service box before starting installation.
2. Electrical connections must comply with local code ordinances, national
electrical codes, CEC, NEC and ANSI/NFPA 70.
3. Make sure the installation site you choose allows the fan blades to rotate
freely without any obstructions.
4. When mounting the fan on a ceiling outlet box, Use an approved (CSA for
Canada and UL for U.S.) ceiling fan box marked "FOR FAN SUPPORT".
5. WARNING: To reduce the risk of fire, electric shock, or personal injury,
mount fan only to an outlet box marked acceptable for fan support and use
mounting screws provided with the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified electrician if in doubt.
Ensure the outlet box is securely installed in place such that it is able to
support at least the fan weight.
three
6.Total Fan Weight For Reference: 42"approximate 7.5 kgs(16.53lbs),
52"approximate 9.0 kgs(19.84lbs).
TROUBLESHOOTING
TROUBLE SUGGESTIONS
- Check fuses and circuit breakers.
1. Fan will not start - Check wiring connections to fan.
- Check wiring connections in switch housing.
CAUTION: Turn power off for last two items.
2. Fan sounds noisy - Check to make sure that all screws in motor housing are snug.
- Check to make sure that blade bracket screws are tight.
- Check to make sure that marrettes in switch housing
are not rattling against wall of switch housing.
- If fan has a light kit make sure switch housing
screws and set screws are tight.
- Some fan motors are sensitive to signals from solid
state variable controls. If solid state controller is
used, change to an alternative control. (See a
representative for a list of available controls.)
- Allow a 24 hour break in period to eliminate most noises.
3. Fan wobbles - Check that all blades are screwed firmly into blade brackets.
or shakes
excessively.
- Check that blade brackets are secured firmly to motor.
- Check distance from tip of blades to ceiling. Gently bend up or
down the blade brackets until all
distances are the same.
- Check distance between blade tip to blade tip. All
measurements should be equal. Loosen blade
screws and position blade until even then re-tighten.
- Check that the downrod hemisphere notch is engaged in canopy.
- Check to make sure that jam screws in downrod are tightened.
- Make sure canopy and mounting bracket are
tightened securely to wooden joist.
- Make sure warpage has not occurred in wooden
blades. If so, contact the customer service department
for replacement parts.

Pg. #3
Pg. #10
1. Wooden Joist
2. Approved (CSA for Canada
and UL for U.S.) ceiling fan box
(not provided)
3. Ceiling
4. J-Hook
5. Rubber Gasket
6. Screws & Lock Washers
(set of 4)
7. Mounting Bracket c/w Ground
Wire
8. Outlet Box Screws (not provided)
9. Rubber Ring (optional)
10. Lock Pin
11. Hemisphere Jam Screw
12. Hemisphere
13. Upper Motor Housing Screws
& Lock Washers (set of 3 or 4)
14. Downrod c/w Ground Wire
15. Ceiling Canopy
16. Rubber Bushing (optional)
17. Bolt
18. Motor Assembly
19. Jam Screws
20. Cotter Pin
21. Nut (optional)
22. Lock Washer (optional)
23. Flat Washer (optional)
24. Hex Nut
32. Blade Bracket Screws
25. Flat Washer
26. Fibre Washer
27. Fibre Bracket Gasket
28. Blade
29. Blade Bracket
30. Lock Washer
31. Motor Screw
With Downrod Without Downrod
1.
2.
3.
4.
5.
6.
7. 8.
10.
11.
12.
13.
14.
15.
17.
18.
15.
16.
18.
19.
20.
21.
22.
23.
25.
26.
28.
25.
26.
28.
Cast Blade
Brackets
Stamped Blade
Brackets
ASSEMBLY DRAWING
27.
29.
30.
31.
32.
24.
30.
32.
Fig. 1
9.
NOTE: Electrical diagrams are for reference only. Light kits that are not packed with the fan must be CSA/UL
Listed and marked approval for use with the model fan you are installing. Switches must be CSA/UL
General Use witches. Refer to the instructions packaged with the light kits and switches for proper
assembly.
WARNING: Check all connections, set screws and screws are securely tightened
before the next step.
BPERMANENTLY ATTACHED LIGHT
- Loosen thumb screws on light.
ADETACHABLE LIGHT KITS
Red or Blue
Wires
Light Kit
Screws
Light Kit
Black Wire
Switch
Housing
White Wires
Lockwasher
White Wire
Screws
Thumb
Screws
Nuts
Chain
Glass Bowl
Lock washer
- Remove 2 clips (optional) and nuts. Loosen third clip (optional) and nut.
Fig.10e
Red or Blue
Wires
Black or
Blue Wires
Red or Blue
Wires
Light Kit
Screws
Light Kit
Black Wire
Switch
Housing
White Wires
Lockwasher
White Wire
Screws
Clips
Chain
Glass
Lock washer
Fig.10f
Red or Blue
Wires
Black or
Blue Wires
Nuts
- Align slots in glass bowl with nipples on
fixture. Slide glass into loosened clip.
Assemble the other 2 clips to the fixture
and then tighten all three nuts in place.
- Connect tassels to switches feeding
chains through nuts on light kit.
NOTE: Pull chain switches are available for some models.
- Loosen thumb screws on light.
- Place shade on light and secure with
thumb screws, finger tight.
- Connect tassels to switches feeding
chains through nuts on light kit.
Fig.10g
- Place shade on light and secure
with thumb screws, finger tight.
Screw
Glass

Pg. #4
NOTE: All set screws must be checked and
retightened where necessary,before and after
installation.
MOUNTING OPTION
CAUTION
Upper Jam
Screw
Upper Jam
Screw
Do not loosen two lower jam screws
Bolt Yolk Yolk
Nut
Flat Washer
Lock Washer
Cotter
Pin
INST
INSTALLA ALLATION TION
DOWNROD MOUNT
- Using a Philips screwdriver loosen the two upper jam screws on the yoke.
- Position downrod inside canopy.
- Route wires exiting yoke on motor through ceiling canopy and downrod.
- Position downrod/canopy into yoke and align holes in yoke and downrod.
- Insert bolt through hole in yoke and downrod. “Be careful not to damage
or cut the fan wires.”
- Tighten flat washer, lock washer, and nut and bolt (not includedon some
models). Secure with cotter pin through hole in the end of the bolt.
- Secure downrod in position by tightening upper jam screws.
1.
A
FLUSH MOUNT
- Remove the yoke screws and lockwashers which correspond to the holes
- Optional for some models -Remove rubber ring from canopy (see fig. 2d)
in the canopy.
- Position canopy over the holes on motor and secure with the same screws
and lockwashers removed in the previous step. Ensure to place the rubber bushing
between the canopy and motor.
B
Motor
Rubber
Bushing
Canopy
Yoke Screws
& Washers
Motor
Canopy
Yoke Screws
& Washers
Rubber
Bushing
Fig. 2a Fig. 2b
Fig. 2c
Fig. 2e Fig. 2f
8.
A
LIGHT KITS (Optional in some fans)
DETACHABLE LIGHT KITS
- Remove light kit screws and washers.
- Connect polarized connectors of light kit to corresponding connectors
found in switch housing.
WARNING: BE SURE TO TURN OFF POWER BEFORE INSTALLING
- Carefully tuck electrical wires back into switch housing, align light kit with
switch housing and secure with three light kit screws and washers.
- Place shades on light kit and secure with either screws,
for pop-off style shades.(See Fig.10a,Fig.10b,Fig.10c,Fig.10d).
Motor
Red, Blue or
Black Wires
Red, Blue or
Black Wires
Light Kit
Screws
Light Kit
Switch Housing
White Wires
Lock washer
Fig. 10a
Shade
Thumb
Screw
Light Kit
Fig. 10c
Glass
Fixture Socket
Spinner Nut
Tool
-
Light Kit Screw
Light Kit
Switch Housing Switch Housing
Fig. 10d
Tool
Spinner Nut
Spinner Nut
Light Kit
White wire White wire
Red or Blue Wires
Black or Blue Wires
Pg. #9
Fibre washer
(Optional)
Canopy
Rubber
ring Fig. 2d
Optional for
some models
for your model)
(Refer to one of the following light kits
finger tight,spinner nut or push and turn
Fig. 10b

Pg. #8 Pg. #5
INSTALL MOUNTING BRACKET
2.
Canopy
J-Hook
Ceiling
- Install J-Hook through centre of outlet box and into the wooden joist.
- Secure mounting bracket and rubber gaskets to outlet box.
- Hang the safety cable onto the J-hook.
- Hang fan on mounting bracket.
WARNING: To Reduce The Risk Of Fi re, Electric Shock, Or Personal
Injury, Mount To UL/CSA Listed Outlet Box Marked Acceptable for
Fan Suppo rt And Use Mounting Sc rews Provided With The Outlet Box.
J- Hook
Safety
Cable
Fig. 3a Fig. 3b
Outlet box Screws
(not provided)
CAUTION
SEE SAFETY PRECAUTIONS ON
PG. #2 BEFORE WIRING
Green Wire - GROUND
Black Wire (Fan) - POWER
White Wire (Fan) - COMMON
Red or Blue Wire (Light Kit) - POWER
ELECTRICAL HOOK UP
- There are several different wiring combinations that can be used in
controlling your ceiling fan to meet your specific requirements. Should
the following method not meet your requirements call or visit your nearest
distributor for a full list of fan accessories.
3.
-
-
After making the wire connections, ensure the wires should be spread
apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box and the ungrounded conductor
on the other side of the outlet box.
Ensure the splices after being made should be turned upward and
pushed carefully up into the outlet box.
MOUNT BLADE BRACKETS TO BLADES
Motor Screw
Motor
Lock Washer
Fibre Bracket Gasket
Cast Blade Brackets
- Place blade bracket screw through flat
washer, fibre washer and blade.
- Align with corresponding hole in
blade bracket.
- Repeat with (2) remaining screws
and tighten.
Stamped Blade Brackets
- Place blade bracket screw through
hole in blade bracket.
- Align with corresponding hole in blade
bracket.
- Place fibre washer and flat washer
over blade bracket screw and secure
with hex nut.
- Repeat with (2) remaining screws and
tighten.
MOUNTING BLADES TO MOTOR
- Take out hardware containing motor screws, lock washers and gaskets.
- Place lock washers over motor screws, position motor screws in blade
brackets, place fibre bracket gaskets over screws and secure to motor.
Make sure all screws are tightened securely.
6.
7.
Hex Nut
Blade
Bracket
Blade Bracket
Screw
Fibre Washer
Flat Washer
Lock Washer
Remove Rubber Stops (optional)
NOTE: Fan comes with three rubber stops (optional on some models)
on motor for shipping purposes only. Remove stops before running motor
or installing blades to motor.
Fig. 9a Fig. 9b
Fig. 8b
Blade Bracket Screw
Fibre Washer
Flat Washer
Blade Bracket
Fig. 8a
Blade Bracket Screw
- Take out hardware package. - Take out hardware package.
Wood
Joist
Outlet Box
Rubber
Gasket
Mounting
Bracket

Pg. #6 Pg. #7
MOUNTING FAN ASSEMBLY
- Place two screws and washers on mounting plate (marked B on diagram)
which correspond with slots in canopy. Screw in two turns.
- Position canopy to mounting plate aligning slots to screws (marked B on
diagram) then turn to lock.
- Position and tighten the two screws and washers (marked A on diagram)
then tighten the two screws (marked B on diagram).
ENGAGE HEMISPHERE (Downrod Mount Only)
- Carefully rotate fan assembly until groove in hemisphere locks over tab of
canopy assembly.
4.
5.
NOTE: When installing fan on sloped ceiling, make sure tab on hanger bracket
faces towards the top of the slope. Depending on the slope, a longer
downrod may be required to prevent fan blades from hitting the ceiling.
WARNING: Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
ELECTRICAL HOOK UP (Continued)
CONNECTING BLACK, WHITE, AND (RED OR BLUE) WIRES
NOTE: Once wires are connected, carefully tuck wires and marrettes into the
outlet box making sure that the wires are clear of the hemisphere
and downrod when positioned in mounting bracket
(Downrod Mount Only).
3.
B
Fig. 6
- Connect white wire from outlet box to white
wire from fan using marret (not supplied).
- Connect black wire from outlet box to black
wire from fan plus (red or blue wire) using
a marret.
NOTE: A red or blue wire would be power
for a light kit if applicable.
Black Wire
White Wire
ELECTRICAL HOOK UP
3.
CONNECTING THE (GREEN) GROUND WIRE
- Connect ground wire from outlet box
to green wire from mounting bracket
and downrod using a
(not supplied).
NOTE: Once ground wires are connected, carefully tuck wires and into the
outlet box making sure that the wires are clear of the hemisphere and
downrod when positioned in mounting bracket (Downrod Mount Only).
- Connect ground wire from outlet box
to green wire from mounting bracket
using a (not supplied).
DOWNROD MOUNT FLUSH MOUNT
A
Fig. 5
Fig. 4
Marette
Marette
marette marette
marette
Downrod
erehpsimeH Groove
(A)
(B)
(B)
Washers
(A)
Fig.7b
Fig.7a
Red or Blue
Wire