Operation
Timer On/Off On-Off Operation SELF-CLEAN Operation
the purpose of this function is to clean the evaporator.
BLANK
0.5h 0.5h 0.5h 0.5h
TIMER ON TIMER OFF TIMER ON-OFF TIMER OFF-ON If this function is needed, please select in the hOn APP.
Press SELF CLEAN button to enter this function. The
display will show "CL" on the panel of the indoor unit and
on the remote controller. Maximum running time in this
function is no more than 21 minutes. This function will exit
automatically with the " Pi " sound twice, then the unit
return to original state.During SELF CLEAN operation,
pressing the button repeatedly will not exit the process.
Press the“power” button to exit this mode.
Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). " "or " "will flash.
3.Press / button to set time.
Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.
Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.
It can be adjusted within 24 hours.
4.Confirm timer setting
After adjust the time,press button and confirm the
CONFIRM
CANCEL
time ON or OFF button will not flash any more.
5.Cancel timer setting
Press the timer button by times until the time display
eliminated.
Hints:
After replacing batteries or a power failure happens, time
setting should be reset.
According to the Time setting sequence of TIMER ON or
Healthy airflow Operation remote controller and panel.
5.If the outside ambient temperature is below zero, error
code “F25 “may be show up during self-cleaning
operation,which is normal protection, please turn off the
power and restart after 10 seconds .
6.The best condition to run this mode, is when the
temperature is 20℃~27℃and the humidity is 35％~60
％indoors, the temperature is 25℃~38℃（cooling
season）outdoors.
7.It is hard for the air to frost if the air is too dry
(humidity＜20%). and if the humidity is too high
(humidity＞70%) the condensate water may increase.
EXTRA
FUNCTION
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations, to choose the swing location
what you needed,and then press
CONFIRM
CANCEL button to confirm.
Healthy Healthy
airflow Present
airflow
upwarder position
downwarder
3.The cancel of the healthy airflow function
EXTRA
FUNCTION
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations again,and then press CONFIRM
CANCEL
button to cancel.
Notice: Do not direct the flap by hand. Otherwise, the
grille will run incorrectly. If the grille is not run correctly, stop
for a minute and then start, adjusting by remote
controller.
Note:
1.After setting the healthy airflow function, the position
grill is fixed.
mode.
mode.
4.In cooling and dry, using the air conditioner for a long
time under the high air humidity, condensate water may
occur at the grille .
1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:
Remote controller:
◆Functional description:
◆Entry and exit：
◆Note:
1.This function is invalid in timer / sleep mode.
2.After this mode starts, the air volume may reduce,
have no airflow, or even cold airflow blowing.
3.It is normal if the unit make some sound when the air
expands with heat and contract with cold.
4. The “CL” display time may last differently on the
1.Press to starting
Setting the comfort work conditions.
2.The setting of healthy airflow function
2.In heating, it is better to select the
3.In cooling, it is better to select the
