Canon PIXMA MX350 User manual

1
Installing Your Multifunction to Your
Network for the First Time
PIXMA MX350 / PIXMA MX870
Windows OS
Next >>

Installing Your Multifunction
to Your Network for the First Time
Preparing to Connect My Multifunction to My Network 3
Network Requirements 3
Important Information You Need Before Adding Your Multifunction 4
Adding Your Multifunction to the Network 5
Confirm Connection Status 9
Downloading & Installing the Drivers 11
Download the Driver 11
Installing the Driver 14
PIXMA MX350 / PIXMA MX870
Windows OS
<< Previous Next >>

3
Preparing to Connect My Multifunction
To My Network
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Notes on Network Connection
•The configuration, router functions, setup procedures and security settings of the network device vary depending on your
system environment. For details, refer to your device's instruction manual or contact its manufacturer.
•The machine cannot be used over a wireless and wired connection at the same time.
Wireless Connection
Connect to your network environment over a wireless connection.
<< Previous Next >>

4
Preparing to Connect My Multifunction
To My Network << Previous Next >>
An "Ad-hoc connection," which establishes a direct
connection to the computer over a wireless connection
without using an access point, is not supported.
Be sure to prepare an access point.
Important InformationYou Need BeforeAddingYour Multifunction
The following information is required to connect to your access point or router.
•Access Point Name/Network Name:
Also referred to as SSID. A name to identify the specific access point.
•Network Key:
Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.
A password required to set to prevent unauthorized access to communication.
Check your access point or router for the following information, and then write it down.
NOTE: For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.

5
Adding Your Multifunction to Your Network << Previous Next >>
Step One
Press the Setup button (A)
Step Two
Select Wireless LAN setup, and then press the OK button.
Adding Your Multifunction to Your Network

6
Adding Your Multifunction to Your Network << Previous Next >>
Step Three
Select Yes, then press the OK button.
When wireless connection is enabled, the Wi-Fi lamp (D)
lights blue.
Step Four
Select Easy setup, and then press the OK button.

7
Adding Your Multifunction to Your Network << Previous Next >>
Step Five
Select the access point name, then press the OK button.
NOTE: If you are living in an apartment, nearby access
points in use may be detected.
Step Six
When one of the following screens is displayed, enter the network
key using the Numeric buttons (E), then press the OK button.
If the following screen is not displayed, go to step 8
Press the button to switch character entry modes.
Enter upper and lower case letters of the alphabet correctly
*

8
Adding Your Multifunction to Your Network << Previous Next >>
Step Seven
Make sure that the network key is correct, and then press
the OK button.
Step Eight
When the connected to the access point screen appears, press the
OK button.
The Setup menu screen returns.
NOTE: If Failed to connect to the access point. appears, press the OK
button, make sure that the network key is correct, then enter it again. If a
connection still cannot be established, refer to the printed manual:
Network Setup Troubleshooting

9
Adding Your Multifunction to Your Network << Previous Next >>
Step One
On the Setup menu, select Device Settings , and
then press the OK button.
IMPORTANT: Confirm connection status after installing the
machine in the target location.
Step Two
Select LAN settings, and then press the OK button.
Confirm Connection Status

10
Adding Your Multifunction to Your Network << Previous Next >>
Step Three
Select Confirm LAN settings, then press the OK button.
Step Four
Select WLAN setting list, then press the OK button.
Make sure that Connection is set to Active, and then press the
Copy button to return to standby.
It may take a while before the connection is complete. In this
case, press the Back* button and wait for about a minute, then
display the Wireless LAN setting list screen again.
*Back button location varies depending on model.
NOTE: If the communication status does not improve, make
sure of the following.
•The machine and network device are turned on.
•There is no obstacle between the machine and access point,
and wireless communication is possible.
•There is no microwave, refrigerator or any other object that
may cause radio interference nearby.