Canon MP730 - MultiPASS Color Inkjet Manual

NOTE
•For information on the components included with your machine and system requirements,
refer to pp.1-1, 1-2, of the Quick Reference Guide.
•When installing the software in Windows 2000/XP, you must log on as Administrator or
have Administrator privileges.
•If you have previously installed an earlier version of the MultiPASS Suite software (version
4.4 or earlier), you must remove it before installing this version. For details on removing the
software, refer to the documentation of the previous version.
Install the software.
1Turn on your computer.
2On your computer, quit any open applications, including virus checkers.
3Insert the Canon MP730/700 Setup CD-ROM into your
disk drive.
When the [MP Setup] screen on the right is displayed,
perform steps 1 and 2 in order.
CAUTION
• Do not perform step 3 on the last page until you reach
it after performing all the other instructions before it.
If this screen is not displayed, on the Windows desktop, double-click [My Computer]
(Windows XP: Click [Start], then click [My Computer]). Open the CD-ROM icon, then
double-click [setup (setup.exe)].
Set-Up Sheet
Set-Up Sheet
IMPORTANT • DO NOT connect the USB cable before installing the software.
Thank you for purchasing the imageCLASS MP730.
To get your machine ready for use, please follow the instructions in this Set-Up Sheet
before referring to any other documentation.
READ THIS SHEET FIRSTREAD THIS SHEET FIRST

●STEP1: Install MP Drivers
1In the [MP Setup] screen, click [Install MP Drivers].
2Follow the on-screen instructions.
[Yes, I want to restart my computer now.] is
selected. (Click [Finish] to restart your computer.
Do not remove the CD-ROM at this stage.)
3Click [Finish].
●STEP2: Install MP Toolbox
1In the [MP Setup] screen, click [Install MP Toolbox].
• When you restart your computer and this screen is not displayed or you have closed it, on
the Windows desktop, double-click [My Computer] (Windows XP: Click [Start], then click
[My Computer]). Open the CD-ROM icon, then double-click [setup (setup.exe)].
2Follow the on-screen instructions.
3Click [Finish].
At this point, DO NOT perform step 3. Continue with the steps on this Set-Up
Sheet until required to connect the USB cable (sold separately).
Remove the shipping material from the machine.
1Place the machine on a flat surface.
2Remove all shipping tapes from the exterior of the machine.
3Open the document cover Aand remove the protective sheet B.
4Open the feeder cover Cand remove the shipping material Das shown below.
D
C
A
B
If you do not need to restart your computer,
the following screen is displayed.
If you need to restart your computer,
the following screen is displayed.

Assemble the machine.
Connect the telephone line and any necessary external
device.
NOTE
• Before using your machine, you need to make sure it is set for your telephone line type.
For details, see p. 7-2 of the Quick Reference Guide.
You can connect an external
device (telephone or answering
machine) if necessary.
Connect the telephone line
cord to the wall jack.
3Attach the document tray,
then lower it.
2Attach the paper output tray
until an audible click is heard.
1Attach the multi-purpose tray.
l Telephone or answering machine
l Built-in computer modem and telephone
Connect external devices as follows:
Telephone
line Machine
Telephone
line Machine
Telephone or
answering machine
Computer
= Telephone line jack
= External device jack
Telephone
TELLINE

Connect the power cord.
IMPORTANT
• Before turning on the power, make sure the document cover Ais closed.
Load paper.
Place a stack of paper (print-side up) in the multi-purpose tray q.Pinch the paper
guide Aand adjust to the width of the stack w.Then place the tray cover Dover
the multi-purpose tray e.
NOTE
•Make sure the stack does not exceed the paper limit mark Bor tab C.Otherwise a paper
jam may occur.
C
q
e
w
D
A
B
PLEASE WAIT
DISPLAY LANGUAGE
< ENGLISH >
Approx. 30 seconds
1Plug the power
cord into a socket.
2When you connect the
machine, the above messages
should appear in the LCD.
•If nothing appears in the LCD,
press [ON/OFF (1 sec.)] to turn on
the machine.
3Use [2] or [3] to select
the language for the
LCD, then press [OK].
A
Turn over to
continue
Turn over to
continue

Install the printhead.
1Press [Open] qand lift up the scanning unit w.
IMPORTANT
• Do not touch the metal rod or any parts inside the
machine.
• Do not turn off the machine when opening the scanning
unit.
2Remove the printhead from its packaging, then remove the orange protective
cap A.
IMPORTANT
•Do not touch the electrical contacts B.
3Raise the lock lever C,then gently slide the printhead into the holder.
Lower the lock lever.
IMPORTANT
• Do not touch the lock lever once the printhead has been installed.
C
B
A
q
w

Install the ink tanks.
1Start with the yellow ink tank. Pull the orange tape in the direction of the arrow
and remove the plastic wrapper so you can see the air hole A.Turn the ink tank
over so that the protective cap Bis facing up. Then hold the ink tank as shown
below and remove the protective cap B.
NOTE
•To avoid spilling ink, never
press on the long sides of
the ink tank C.
•Once you remove the
protective cap B,do not
touch the ink port D.
2Insert the ink tank (label-side up) into the correct slot (refer to the color guide on
the printhead). Press down gently on the ink tank until an audible click is heard.
3Repeat steps 1 and 2 to install the remaining magenta, cyan, and black ink tanks.
4Close the scanning unit until it locks into place.
Be sure to now align the printhead as explained in step 9.
Black
Yellow
Magenta
Cian
Black
BCI-3eC
BCI-3eBK BCI-3eM BCI-3eY
Yellow
Magenta
Cian
PUSHPUSHPUSH
PUSH
Black
Black Yellow
Magenta
Cian
Black
BCI-3eY
Yellow
PUSH
Black Yellow
Magenta
Cian
Black
BCI-3eY
Yellow
PUSH
PUSU
Yellow
MadeinJapan
Ink Tank
BCI-3eY
PULL
PULL
BCI-3eY
Ink Tank
A
BB
DC

Align the printhead.
NOTE
• If you are installing the software, you can also align the printhead from the software.
For details, refer to the Software Guide.
1When the LCD Adisplays the following, press [OK].
The machine will print a horizontal pattern, and the LCD will display:
2In column A on the printout, note which box has the most solid image. Note the
value next to this box and use [2] or [3] on the operation panel to enter it.
Then press [OK].
3Repeat step 2 for columns B to K.
4When values for all columns have been entered and the LCD displays the
following, press [#] to return to standby mode.
NOTE
•If streaks appear on the printed
surface when you use the machine,
perform the vertical printhead
alignment. For details, refer to the
User’s Guide.
PRINT VERT. PATTERN?
YES=(A) NO=(#)
Most solid
box
Least solid
box
BAD
SAMPLE
GOOD
SAMPLE
Column A Value for column A
CHANGE H VALUE
A 0
ALIGN PRINT HEAD
PRESS OK KEY A

Connect the USB cable to complete the computer settings.
●STEP3: Connect the machine to your computer with the USB cable.
1Make sure the machine is turned on.
2Connect the USB cable Ato the machine and computer USB ports.
Depending on your computer, a message may display asking you to restart your
computer. If this is the case, restart your computer.
●Install Utility Software
To install the Utility software, in the [MP Setup] screen, click [Install Utility
Software].
You can choose not to install the Utility software at this stage and install it later.
●View User’s Manual
To read the manual on the CD-ROM, click [View User’s Manual] on the [MP Setup]
screen.
CAUTION
• For Windows 2000, the machine may not be able to be set as the default printer.
If that happens, refer to Setting the default printer in the Software Guide.
Congratulations! You have now completed your machine
setup.
Where to from here...
Once you have completed all steps in this Set-Up Sheet, refer to the Quick Reference
Guide for basic operation instructions of all functions of your machine.
If after reading the Quick Reference Guide you require more detailed information,
refer to the User’s Guide or Software Guide (included in the CD-ROM).
A
Part no. HT3-2133-000-V.1.0
© 2003 Canon Inc.
Canon, imageCLASS, and BCI are trademarks of Canon Inc.
All other products and brand names are registered
trademarks or trademarks of their respective owners.
Specifications subject to change without notice.
PRINTED IN THAILAND