Canon WFT-E7 User manual

INSTRUCTION MANUAL
E
Wireless File Transmitter
for EOS R
WFT-E7 (Ver.2)
This manual is for the WFT-E7 (Ver.2) installed with firmware version 1.4.0
or later.

2
The transmitter is an accessory for EOS cameras that enables LAN
functions to be used when attached to the camera.
Using the transmitter’s LAN functions enables you to do the following:
Transfer images to an FTP server
Use EOS Utility to shoot, view, and download images
remotely
Introduction
What You Can Do with the Transmitter
FTP Transfer (p.31)
EOS Utility (p.49)

3
To comply with local radio wave regulations, Canon offers five
region-specific versions of the transmitter (A, B, C, D, and E) in
various areas around the world (see separate sheet). For
convenience, the product in this manual is referred to as “WFT-E7
(Ver.2)”, without reference to the versions A, B, C, D, or E.
In this manual, the term “access point” indicates wireless LAN
access points, wireless LAN routers, etc. that relay a LAN
connection.
These instructions should be followed only after setting up your LAN
and FTP server environments. For information about setting up the
environments, refer to the documentation provided with each device
or contact the manufacturer.
Read the Camera Instruction Manual and familiarize yourself with
operating the camera before following the instructions on camera
options.
Icons in this Manual
<6> : Indicates the Main Dial.
<5> : Indicates the Quick Control Dial.
<W><X><Y><Z> : Indicates the <V> cross keys on the top, bottom,
left, and right.
<0>: Indicates the Setting button.
* In addition to the above, the icons and symbols used on the camera’s buttons
and displayed on the monitor are also used in this manual when discussing
relevant operations and functionality.
(p.**) : Reference page numbers for more information.
: Warnings to prevent potential problems during operation.
: Supplemental information.
Conventions Used in this Manual

4
Conventions Used in this Manual
Basic Assumptions
All operations explained in this manual assume that the power
switch is set to <1>.
It is assumed that all the menu settings, Custom Functions, etc. are
set to their defaults.
Image transfer, remote shooting, or image viewing requires adequate
knowledge of configuring your LAN and FTP server. Canon cannot provide
support for configuring LANs or FTP servers.
Note that Canon cannot be held liable for any loss or damage to the
transmitter from erroneous network or FTP server settings. In addition,
Canon cannot be held liable for any other loss or damage caused by use of
the transmitter.
When using LAN functions, establish appropriate security at your own risk
and discretion. Canon cannot be held liable for any loss or damage caused
by unauthorized access or other security breaches.

5
Chapter List
Introduction 2
Basic Network Settings 17
Transferring Images to an FTP Server 31
Operating Remotely Using EOS Utility 49
Terminating the Connection and Reconnecting 53
Checking and Operating Connection Settings 57
Troubleshooting Guide 69
Reference 91
1
2
3
4
5
6
7

6
2
1
3
4
Introduction 2
Conventions Used in this Manual..................................................... 3
Chapter List ...................................................................................... 5
Safety Instructions............................................................................ 8
Nomenclature ................................................................................. 10
Installing and Removing the Battery............................................... 12
Using a Household Power Outlet ................................................... 14
Attaching to the Camera................................................................. 15
Basic Network Settings 17
Preparation..................................................................................... 18
Displaying the Connection Wizard ................................................. 20
Checking the Type of Access Point................................................ 22
Connecting via WPS (PBC Mode).................................................. 23
Connecting via WPS (PIN Mode) ................................................... 24
Connecting to a Detected Network Manually ................................. 26
Setting the IP Address.................................................................... 29
Transferring Images to an FTP Server 31
Configuring FTP Server Connection Settings ................................ 32
Transferring Images Individually..................................................... 37
Batch Transfer ................................................................................ 42
Transferring Images with a Caption................................................ 46
Viewing Transferred Images........................................................... 47
Operating Remotely Using EOS Utility 49
Configuring EOS Utility Connection Settings ................................. 50
Using EOS Utility............................................................................ 52
Terminating the Connection and Reconnecting 53
Terminating the Connection............................................................ 54
Reconnecting ................................................................................. 55
Contents

7
Contents
6
7
5Checking and Operating Connection Settings 57
Displaying the Connection Settings Screen....................................58
Changing Settings...........................................................................60
Saving and Loading Settings ..........................................................64
Function Settings Screen................................................................66
Troubleshooting Guide 69
Responding to Error Messages ......................................................70
Wireless Function Notes .................................................................86
Security ........................................................................................... 88
Checking Network Settings.............................................................89
Reference 91
Creating and Registering Captions .................................................92
Setting IP Address Manually...........................................................94
Using a Bracket (Sold Separately)..................................................96
Specifications .................................................................................. 97
Index .............................................................................................101

8
Be sure to read these instructions in order to operate the product safely.
Follow these instructions to prevent injury or harm to the operator of the
product or others.
Safety Instructions
WARNING Denotes the risk of serious injury or death.
Use only power sources specified in this instruction manual for use with the product.
Do not disassemble or modify the product.
Do not expose the product to strong shocks or vibration.
Do not touch any exposed internal parts.
Stop using the product in any case of unusual circumstances such as the presence
of smoke or a strange smell.
Do not use organic solvents such as alcohol, benzine or paint thinner to clean the
product.
Do not get the product wet. Do not insert foreign objects or liquids into the product.
Do not use the product where flammable gases may be present.
This may cause electric shock, explosion or fire.
Observe the following instructions when using commercially available batteries or
provided battery packs.
• Use batteries/battery packs only with their specified product.
• Do not heat batteries/battery packs or expose them to fire.
• Do not expose the terminals to dirt or let them come into contact with metallic pins
or other metal objects.
This may cause electric shock, explosion or fire.
Follow any indications to turn off the product in places where its use is forbidden.
Not doing so may cause other equipment to malfunction due to the effect of
electromagnetic waves and even result in accidents.
CAUTION Denotes the risk of injury.
Do not leave the product in places exposed to extremely high or low temperatures.
The product may become extremely hot/cold and cause burns or injury when touched.

9
Safety Instructions
The transmitter is a precision instrument. Do not drop it or subject it to
physical shock.
The transmitter is not waterproof. Do not use it underwater.
Wipe off any moisture with a dry and clean cloth. If the transmitter has been
exposed to salty air, wipe it with a clean, well-wrung wet cloth.
Never leave the transmitter near any equipment that generates a strong
magnetic field, such as magnets or electric motors.
Do not leave the transmitter in excessive heat, such as in a vehicle in direct
sunlight. High temperatures may damage the transmitter.
Do not wipe the transmitter using cleaners containing organic solvents. For
stubborn dirt, take it to the nearest Canon Service Center.
Avoid storing the transmitter where there are chemicals that result in rust
and corrosion such as in a chemical lab.
Handling Precautions

10
LCD panel
* Bluetooth connectivity is not supported on the EOS R.
Nomenclature
Battery compartment
cover (p.12)
Battery compartment
cover release lever
(p.12)
Power lamp
(p.15)
<
LAN > lamp
LCD panel
Power switch (p.15)
Tripod screw
<a> port (p.15) Ethernet RJ-45 port
Error code number
Wireless signal strength
Battery check
Connection icon
Wired LAN
connection
Bluetooth connection*

11
Nomenclature
Case and other accessories
Interface cables
When connecting to the EOS R, use either IFC-40AB III (40 cm / 1.3 ft.; sold
separately) or IFC-150AB III (1.5 m / 4.9 ft.; sold separately). The included
interface cables cannot be used for the connection.
Strap mounts
Belt holder
Case strap Case for tripod screw
Cap for preventing
cable disconnection

12
Use one Battery Pack LP-E6N (or LP-E6) to power the transmitter.
When replacing the transmitter’s battery, be sure to turn the transmitter
off before opening the battery compartment cover.
Also note that the transmitter is not sold with a battery or charger. If you
do not own these accessories, they are available for purchase
separately.
1Open the cover.
Push the lever down and open the
cover.
2Insert the battery.
Insert the end with the battery
contacts.
Insert the battery all the way until it
locks into place.
3Close the cover.
Press the cover up until it clicks into
place.
Installing and Removing the Battery
Installing the Battery

13
Installing and Removing the Battery
The remaining battery level is displayed when you turn the transmitter
on. A blinking battery icon (b) indicates that the battery will be
depleted soon.
1Open the cover.
Push the lever down and open the
cover.
2Remove the battery.
Press the battery lock lever in the
direction of the arrow to unlock, and
then remove the battery.
To prevent a short-circuit, be sure to
always attach the protective cover to
the battery.
Battery Check
Icon zxcm
bn
Level (%) 100 – 70 69 – 50 49 – 20 19 – 10 9 – 1 0
Removing the Battery

14
You can power the transmitter with a household power outlet by using
the DC Coupler DR-E6 and AC Adapter AC-E6N (each sold
separately).
1Insert the DC coupler.
Open the battery compartment cover
and open the DC coupler cord hole
cover.
Insert the DC coupler securely until it
locks and put the cord through the
hole.
Close the cover.
2Connect the DC coupler’s plug.
Connect the DC coupler’s plug and
the AC adapter’s connector securely.
3Connect the power cord.
Connect the power cord as shown in
the illustration.
After using the camera, unplug the
power plug from the power outlet.
Using a Household Power Outlet
DC coupler cord hole
Do not connect or disconnect the power cord or DC coupler while leaving
the transmitter’s power switch set to the <1> position.
Do not connect both the transmitter and camera to a household power
outlet and use them simultaneously. It may cause malfunction to the
nearby electronic devices. For more information, contact your dealer or
nearest Canon Service Center.
AC Adapter Kit ACK-E6 (sold separately) can also be used.

15
When connecting the transmitter to the camera, always use one of the
interface cables included with the transmitter.
1Turn off both the transmitter and
camera.
2Attach the transmitter’s
<a> port cap.
Attach the cap for preventing cable
disconnection.
3Connect the transmitter and
camera.
For the interface cable, use either
IFC-40AB III (40 cm / 1.3 ft.; sold
separately) or IFC-150AB III (1.5 m /
4.9 ft.; sold separately).
Attach the cable protector to the
camera and run the cable through the
clamp.
For cable protector instructions, refer
to the camera instruction manual.
4Turn on both the transmitter and
camera.
The transmitter’s <3> lamp will
light and <D> will be displayed on
the transmitter’s LCD panel.
Attaching to the Camera
GPS
WFT
CAMERA

16
Attaching to the Camera
Connect the transmitter to the camera using IFC-150AB III.
Example of Using the Case and Strap
Before disconnecting the cable, turn off both the transmitter and camera.
If you turn on/off the transmitter or connect/disconnect the interface
cable during movie shooting, movie shooting will stop.
If wireless functions are in use, noise may be recorded regardless of the
use of the built-in microphone(s) or an external microphone. It is
recommended that you do not use wireless functions when shooting
movies.
If the transmitter’s <3> lamp blinks, it means that the transmitter and
camera are not properly connected. Check the connection.

17
1
Basic Network Settings
Complete the basic network settings by using the menu
screen on the camera’s monitor.

18
[FTP trans.]
You can transfer captured images to an FTP server.
Images can be automatically transferred as you shoot them, or you
can select images to be transferred later.
Computer Operating Systems
Use of [FTP trans.] requires that one of the following operating
systems be installed on a computer. In addition, the computer must
be set up as an FTP server in advance.
• Windows 10
• Windows 8, Windows 8 Pro, Windows 8.1, Windows 8.1 Pro
• Windows 7 (Professional, Enterprise, or Ultimate Edition for
32- or 64-bit systems)
For instructions on setting up a computer as an FTP server, refer to
the documentation provided with each device or contact the
manufacturer.
Note that the following operating systems cannot be used
because FTP server functionality is not provided.
• Windows 7 Home Premium
Preparation

19
Preparation
[EOSUtility]
You can perform remote shooting over a LAN using EOS Utility
(EOS software).
In addition to remote shooting, almost all EOS Utility camera
operations are supported, because this option utilizes a LAN instead
of an interface cable.
Requires a computer with EOS Utility (EOS software) installed.
When connecting using an access point, connect the target device to
the access point in advance.
Connecting Using an Access Point
Transfer of Movies over Wireless LAN
Because of the large size of individual movie files, wireless LAN file
transmission takes some time. Set up an environment where each device
can achieve stable communication with the access point and the transmitter
by referring to the information on page 86.

20
This section describes the process following the connection
instructions. If an error is displayed, see “Troubleshooting Guide” in
Chapter 6 (p.69) and check the settings.
Pressing the shutter button or other camera controls during
configuration using the connection instructions will close the
connection instructions. Do not press the shutter button or other
controls until configuration is finished.
1Turn on the transmitter.
2Select [55: WFT settings].
3Select [Connection settings].
4Select [SET*].
Displaying the Connection Wizard