Cansec SmartLock UltraLite Plus User manual

SmartLock®UltraLite Plus
INSTALLATION MANUAL
October 2015

SmartLock®UltraLite Plus Page 2 of 16
Installation Manual Oct 2013 • Rev. 1.6
Table of Contents
INTRODUCTION ........................................................................................................................................... 3
SPECIFICATIONS......................................................................................................................................... 4
BOARD LAYOUT.......................................................................................................................................... 5
WIRING ......................................................................................................................................................... 6
LOCK RELAY WIRING............................................................................................................................... 10
TROUBLESHOOTING ................................................................................................................................ 14
SMARTLOCK ULTRALITE PLUS COMPLIANCE STATEMENT............................................................... 15
Copyright 2012 - 2015 Cansec Systems, Ltd.
All rights reserved.
Connector Installation Note................................................................................6
Wiegand Reader................................................................................................7
iButton®Reader ................................................................................................. 8
Exit Button and Door Contact.............................................................................9
DC Electric Strikes (up to 250mA)....................................................................10
DC Electric Strikes (more than 250mA) ...........................................................11
AC Electric Strikes ...........................................................................................12
AC Maglocks....................................................................................................13

SmartLock®UltraLite Plus Page 3 of 16
Installation Manual Oct 2013 • Rev. 1.6
Introduction
SmartLock UltraLite Plus is an extremely simple, stand-alone access control system that
supports up to 2,000 users with a 1,000 record, time-stamped audit trail capacity. All
programming is done at the PC, using software which is simple, intuitive and supports
up to 255 UltraLite Plus controllers. When used with the CanProx One proximity
reader, the UltraLite Plus system becomes one of the most cost-effective stand-alone,
expandable systems on the market.
The SmartLock UltraLite Plus controller features a form "C" relay output for lock
control as well as inputs for a request-to-exit button and a door contact. If a door
contact input is connected, the controller will automatically relock the door once it re-
closes. In addition, an audible alert can be generated on the reader if the door is held
open longer than a specified time.
IMPORTANT: If no door contact is used, the door contact input must be shorted to
ground. Failure to do this will result in erratic operation.
NOTE: Tech Support will only be provided where product installation guidelines
have been followed.
IMPORTANT: In some jurisdictions the use of a UL-approved power supply
and connection to the fire alarm system for emergency release may be
required. Installers should contact the fire marshal office or local
authority having jurisdiction to verify the specific requirements. A building
permit may be required in some jurisdictions for the installation of maglocks.

SmartLock®UltraLite Plus Page 4 of 16
Installation Manual Oct 2013 • Rev. 1.6
Specifications
Power Requirements
UltraLite Plus controller ........................................................................12 VDC, 40 mA
NOTE: When determining power supply current requirements, add lock and reader current draw.
Onboard Output
Lock control relay.........................................................form “C”, rated @ 30 VDC, 2 A
Onboard Inputs
Exit button ............................................................................................... normally open
Door contact........................................................................................... normally closed
Reader Cable
Wiegand readers..................................................6 conductors (twisted pair not required)
..................................................................................#22 AWG, overall shielded cable
.......................................................................................................... 152 m [500'] max.
iButton®readers................................................................................................. 6 conductors
......................................................................#22 AWG, shielded or unshielded cable
...............................................................................................................15 m [50'] max.
Dimensions
UltraLite Plus controller .............................114.3 mm (h) x44.5 mm (w) x25.4 mm (d)
...........................................................................................[4.5'' (h) x1.75'' (w) x1'' (d)]
Operating Temperature.............................................. -35oC to 65oC [-31oF to 150oF]
Housing................................................................................................... polycarbonate
Specifications subject to change without notice.
IMPORTANT: In some jurisdictions the use of a UL-approved power supply
and connection to the fire alarm system for emergency release may be
required. Installers should contact the fire marshal office or local
authority having jurisdiction to verify the specific requirements. A building
permit may be required in some jurisdictions for the installation of maglocks.

SmartLock®UltraLite Plus Page 5 of 16
Installation Manual Oct 2013 • Rev. 1.6
Board Layout
NOTE:
1. Only connect a power source to the indicated power pins or product damage will result.
2. The door contact input must be bypassed if not used. To bypass, connect a jumper wire
between the door contact input and Ground.
3. If the cable feed hole on the controller back-box is too small, drill a larger hole to
accommodate the cable.
4. The controller comes in polycarbonate housing, and should be installed in an accessible
location on the secure side of the door.
5. The housing is not waterproof.

SmartLock®UltraLite Plus Page 6 of 16
Installation Manual Oct 2013 • Rev. 1.6
Wiring
CONNECTOR INSTALLATION NOTE
IMPORTANT:
Wires face into the center of the PCB for installation into housing.
CONNECT WIRES ONTO THE
PLUGGABLE CONNECTORS
IN THIS ORIENTATION
ATTACH CONNECTORS
AS SHOWN

SmartLock®UltraLite Plus Page 7 of 16
Installation Manual Oct 2013 • Rev. 1.6
WIEGAND READER
IMPORTANT: Before applying power to the controller, verify that the reader is
connected correctly as per the manufacturer’s specifications.
6 CONDUCTOR, 20 AWG
NON-TWISTED PAIR
SHIELDED CABLE
MAX. DISTANCE IS 500 FT.

SmartLock®UltraLite Plus Page 8 of 16
Installation Manual Oct 2013 • Rev. 1.6
IBUTTON READER
6 CONDUCTOR, 22 AWG
TWISTED OR NON-TWISTED PAIR
SHIELDED CABLE
MAX. DISTANCE IS 50 FT.

SmartLock®UltraLite Plus Page 9 of 16
Installation Manual Oct 2013 • Rev. 1.6
EXIT BUTTON AND DOOR CONTACT
NOTE:
1. Do not apply power or attempt to switch any current through these inputs as this
will result in damage to the controller.
2. The door contact input is used for forced entry and door-held-open
annunciation. The lock relay is deactivated when the door closes before the
unlock time ends.
3. If door contact is not used, you must connect a jumper wire between the door
contact input and Ground. Connecting a door contact will enable door-held-
open annunciation via the reader’s beeper and will also deactivate the lock relay
when the door closes before the unlock time ends.
4. Requires momentary closure to activate the lock relay.

SmartLock®UltraLite Plus Page 10 of 16
Installation Manual Oct 2013 • Rev. 1.6
Lock Relay Wiring
DC ELECTRIC STRIKES (UP TO 250MA)
NOTE: Use a 1N400x series diode at the lock device as shown to prevent “back EMF”
from damaging the controller.

SmartLock®UltraLite Plus Page 11 of 16
Installation Manual Oct 2013 • Rev. 1.6
DC ELECTRIC STRIKES (MORE THAN 250MA)
NOTE: Place a 1N400x series diode at the external relay coil as shown to prevent “back
EMF” from damaging the controller.

SmartLock®UltraLite Plus Page 12 of 16
Installation Manual Oct 2013 • Rev. 1.6
AC ELECTRIC STRIKES
NOTE: Place a 1N400x series diode at the external relay coil as shown to prevent “back
EMF” from damaging the controller.

SmartLock®UltraLite Plus Page 13 of 16
Installation Manual Oct 2013 • Rev. 1.6
AC MAGLOCKS
NOTE: Place a 1N400x series diode at the external relay coil as shown to prevent “back
EMF” from damaging the controller.
IMPORTANT: In some jurisdictions the use of a UL-approved power supply
and connection to the fire alarm system for emergency release may be
required. Installers should contact the fire marshal office or local
authority having jurisdiction to verify the specific requirements. A building
permit may be required in some jurisdictions for the installation of maglocks.

SmartLock®UltraLite Plus Page 14 of 16
Installation Manual Oct 2013 • Rev. 1.6
Troubleshooting
The SmartLock UltraLite Plus uses a series of ON/OFF tones (beeps) to indicate
operational status to the user. These beeps can be used for troubleshooting.
NOTE: The UltraLite Plus controller emits two types of beeps: high (2,300 Hz)
and low (675 Hz).
Condition
Time (ms = millisecond)
Mode
Power Up
100 ms ON
Single Beep
Real-Time Clock
Failure
150 ms ON
150 ms OFF
Continuous
Beeps
Access Granted
130 ms ON
Single Beep
Access Denied
first beep: 130 ms ON then 20 ms OFF
second beep: 130 ms ON then OFF
Two Beeps
Door-Held-Open
Continuous tone
Continuous
Beep
Programming
Successful
transfer start: 1 s ON at 2,300 Hz (high beep).
during transfer: 500 ms ON and 500 ms OFF.
transfer end: 2 s ON at 675 Hz (low beep).
Low Beep at
End
Programming
Unsuccessful
start: 1 s ON at 2,300 Hz (high beep)
error: 130 ms ON and 20 ms OFF
Four Beeps
Data Transfer
500 ms ON
500 ms OFF
Continuous
Beeps
® SmartLock is a registered trademark of Cansec Systems, Ltd.
® iButton is a registered trademark of Maxim Integrated Products, Inc.

SmartLock®UltraLite Plus Page 15 of 16
Installation Manual Oct 2013 • Rev. 1.6
Compliance statements for :
Federal Communications Commission (FCC)
Statement
Note: This equipment has been tested and found to comply with the limits for a class B digital
devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interferences, and (2) this device must accept
any interferences received, including interference that may cause undesired operation.
Complies To:

SmartLock®UltraLite Plus Page 16 of 16
Installation Manual Oct 2013 • Rev. 1.6
Industry Canada Compliance Statement
This Class B digital apparatus meets the requirements of the Canadian Interference-Causing
Equipment Regulations.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel
brouilleur du Canada.
Complies To:
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B Information
Technology Equipment according to CISPR 11 / European Standard EN 55011. The limits for Class
B equipment were derived for typical residential environments to provide reasonable protection
against interference with licensed communication devices.
Complies To: