Cansec Zodiac LITE User manual

Zodiac LITE
INSTALLATION INSTRUCTIONS
May 2008

Page: 2/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
Table of Contents
Introduction....................................................................................................................................................................3
Specifications.................................................................................................................................................................3
Zodiac Lite Reader & Wiring...................................................................................................................................... 4-5
Zodiac Door Control Module (ZDCM).............................................................................................................................6
Wiring the Zodiac Lite Stand-Alone Kit...........................................................................................................................7
Wiring Lock Devices
Electric Strikes.................................................................................................................................................8
Maglocks..........................................................................................................................................................9
© Cansec Systems Ltd., 2008
A
ll ri
g
hts reserved.

Page: 3/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
Introduction
The Zodiac LITE biometric fingerprint reader allows all programming and user management to take place right at
the reader, without having to run cables to a PC. Up to 90 user templates can be stored in the reader’s non-volatile
memory. When used with a power supply and a door control module, this reader becomes the focal point of a 100
per cent PC-free, stand-alone door access control system.
Specifications*
ZODIAC LITE READER
Power Requirements: ........................................................................................................................... 12 VDC, 300 mA
Wiegand Cable: .................................................................................22 AWG, 6 conductors, Stranded, Overall Shield,
Maximum 152 m (500 ft) to controller
Reader Output:
Reader Mode: .................................................................................................. 26-bit or Cansec 37-bit Wiegand
DCM Mode ................................................................................................. Cansec proprietary DCM Wiegand
Operating Temperature: .................................................................................................... -15°C to 60°C (5°F to 140°F)
Size: .........................................................87 mm (w) x 144 mm (h) x 38 mm (d) [3.4 in (w) x 5.7 in (h) x 1.5 in (d)]
Weight: ...........................................................................................................................................................397 g (14 oz)
Housing:..................................................................................................................................................High impact ABS
Mounting:...................................................................................................................................Single-gang electrical box
Sensor:
Manufacturer: ............................................................................................................................................ Nitgen
Type: .........................................................................................................................................................Optical
Authentication: ...................................................................................................................................<1 Second
LED Indicators:.................................................................................................................Bi-colour standard (red, green)
1 x authentication indicator (left)
1 x externally controlled indicator (right)
Audio Tone: ...............................................................................................................................................Internal beeper
ZODIAC DOOR CONTROL MODULE
Power Requirements: ..............................................................................................................................12 VDC, 50 mA
Operating Temperature: ................................................................................................. -40°C to 85°C (-40°F to 185°F)
Size: ...........................................................36 mm (w) x 61 mm (h) x 10 mm (d) [1.4 in (w) x 2.4 in (h) x 0.4 in (d)]
Weight: ..............................................................................................................................................................28 g (1 oz)
Lock Relay (on ZDCM)
Arrangement: ................................................................................................................................................. Form C
Nominal Switching Capacity:................................................................................................................2 A, 30 VDC
*Specifications subject to change without notice

Page: 4/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
Zodiac Lite Reader & Wiring
ZODIAC Lite READER
- The left LED indicates authentication and is internally
controlled by the reader.
- The right LED is externally controlled by the host
controller. It changes from red to green when the LED
line is pulled low.
MOUNTING PLATE
- Surface mount fits standard single-gang electrical box
- Shown below in the upright position
ZODIAC LITE WIRING
POWER REQUIREMENTS
-+12 VDC, 300 mA
CABLE SPECIFICATIONS:
-6 conductors
-22 AWG
-Stranded wire
-Overall shield
-152 m (500 ft.) max. length

Page: 5/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
8-PIN CONNECTOR
- For wiring to a Wiegand controller or a Zodiac Door
Control Module
SET SCREW
- Insert from bottom of reader after mounting on
mounting plate
DIP SWITCHES
DIP SWITCH # ON OFF
1 DCM MODE READER MODE
2 Normal
Security
MODE
High
Security
MODE
3 N/A N/A
4 N/A N/A
DCM MODE:
If you are connecting Zodiac Lite to ZDCM board, DIP switch # 1 has to be in ON position.
READER MODE:
If you are connecting Zodiac Lite to any Access Panel (CP40, SmartLock Pro or any 26-bit access panel),
DIP switch # 1 has to be in OFF position.
NORMAL SECURITY MODE:
By default setup DIP switch #2 is in ON position, in this case Zodiac performs a normal authentication process.
HIGH SECURITY MODE:
In this mode Zodiac performs a high authentication process.
If any changes are made at the DIP switch setting press RESET BUTTON to apply new setup.

Page: 6/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
Zodiac Door Control Module
The Zodiac Door Control Module (ZDCM) is available in two mounting assemblies. In either case the ZDCM
should be installed on the secure side of the door.
1. HEATSHRUNK PCB
The standard mounting method for the ZDCM
is to simply place the entire ZDCM into a wall
cavity or a standard single-gang box. Screws are
not required to mount the board. The PCB is
insulated with heat shrink tubing. The
connector and labels are exposed for device
connectivity. After connections are complete,
the module can be placed in a secure location. If
you place the ZDCM in a standard electrical box,
a gang plate cover can be used to cover the opening of the
electrical box.
2. MOUNTED ON A SINGLE GANGPLATE
The second mounting method
available is to have the ZDCM
pre-mounted on a standard single-
gang electrical plate. After wiring is
complete, simply screw the ZDCM
into a standard single-gang electrical
box.
ZDCM CONNECTIONS
D
R
R
T
E
R
E
L
A
Y
R
E
A
D
E
R
+12 VDC
INPUT
DOOR
CONTACT
REQUEST
TO EXIT
LOCK DEVICE
RELAY
ZODIAC 250
READER
CONNECTION
+12V
IN
GND
(NC)
GND
(NO)
GND
+12V
OUT
COM
NO
NC
GND
D0
D1
LED
GND
+12V
OUT
ARE YOU USING A DOOR CONTACT ON THE ZDCM?
NO – You must short the door contact points on the board (see diagram at right). Unlock
time is fixed at seven (7) seconds. The right LED on the front of the reader will turn
GREEN during the unlock time.
YES – Unlock time is seven (7) seconds. However, when you open and re-close the door before the unlock time
ends, the unlock time is terminated and the door will relock upon closing. The right LED on the front of
the reader will turn GREEN when the door contact opens and turn RED when the door contact closes.
+12V
IN
GND
(NC)
GND
(NO)
GND
+12V
OUT
COM
NO
NC
GND
D0
D1
LED
GND
+12V
OUT
D
R
R
T
E
R
E
L
A
Y
R
E
A
D
E
R
+12V
IN
GND
(NC)
GND
(NO)
GND
+12V
OUT
COM
NO
NC
GND
D0
D1
LED
GND
+12V
OUT
D
R
R
T
E
R
E
L
A
Y
R
E
A
D
E
R
(NC)
GND
JUMPER
WIRE

Page: 7/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
Wiring the Zodiac LITE Stand-Alone Kit
When you are wiring a Zodiac LITE reader to a Zodiac Door Control Module, the reader must be set to DCM
Mode. Refer to the “Wiring” paragraph for more information.

Page: 8/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
Wiring Lock Devices
ELECTRIC STRIKES
Powering 12 VDC electric strikes from the
Zodiac Door Control Module: Powering DC electric strikes from a separate external DC power supply:
Note: Use 1N400x series diode as shown to suppress “Back EMF” from damaging the controller.

Page: 9/9
Zodiac LITE Installation Instructions May 2008 !Rev 1.5
MAGLOCKS
Powering 12 VDC maglocks from the Zodiac
Door Control Module: Powering DC maglocks from a separate external DC power supply
ZODIAC DOOR
CONTROL MODULE
JUMPER
WIRE
12 VDC MAGLOCK
MAX)
(2 A
12 VDC
SUPPLY
+ 12V IN
GND
+12V OUT
COM
NO
NC
GND
1N400x Diode
ZODIAC DOOR
CONTROL MODULE
MAGLOCK
( MAX)
2 A, 30 VDC
EXTERNAL
POWER
SUPPLY
DC
12 VDC
SUPPLY
+ 12V IN
GND
+12V OUT
COM
NO
NC
GND
1N400x Diode
Note: Use 1N400x series diode as shown to prevent “Back EMF” from damaging the controller if the maglock is
not equipped with sufficient spike and surge protection. Check the maglock specifications for details.