alcatraz ROCK-1 User manual

The Rock
Install Guide

Panel +12v * RED
Panel GND * BLACK
Panel D0 / RS485A * GREEN
Panel D1 / RS485B * WHITE
Panel Beeper YELLOW
Panel Tamper VIOLET
Panel Hold BLUE
Panel LED Green * ORANGE
Panel LED Red BROWN
Badge Reader +12v * RED
Badge Reader GND * BLACK
Badge Reader D0 / RS485A * GREEN
Badge Reader D1 / RS485B * WHITE
Badge Reader Beeper YELLOW
Badge Reader Tamper VIOLET
Badge Reader Hold BLUE
Badge Reader LED Green ORANGE
Badge Reader LED Red BROWN
Wiring Table
Mount 2-gang switch box in wall
Installation to be performed only by certified installer
Power Requirement: PoE+ (802.3at Type 2) 30W
Unit to be powered by UL294B certified IEEE PoE+ 802.3at Type 2
Power Sourcing Equipment using shielded cat5e or higher cable
Wiegand Maximum Cable Length: 500 ft - 22 AWG (152 m), 300 ft - 24
AWG (91 m)
Complies with US FDA performance standards for laser products except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007
CAUTION: Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure
Step 1 –Installation Prerequisite
Parts Included
1x Alcatraz Rock
1x Wall Mount
1x Wiring Harness
1x Wall release tool
4x Cable Ties
4x Mounting Screws #6-32
Required tools and supplies
2-Gang switch box
Gel filled B connectors or equivalent
22/6 cable, 5-9 conductor, Genesis 12061109 or equivalent (Wiegand)
4 conductor shielded twisted pair, Belden 3107A or equivalent (OSDP)
Level
Measuring tape
Wire stripper / cutter
Phillips screwdriver
Panel Cable Badge Reader Cable
Install on door opening side
* Required for operation
5ft (1.5m) from floor
½” (13mm) minimum
Screw tabs must be in
vertical position
Badge reader
mounted at
standard height
Position close to door
Leave minimum of ½”
between 2-gang switch
box and door frame
2-gang
switch box

READER
PANEL
Thread cables through and attach
wall plate to 2-gang box
Wire cable harness to badge reader
and access control panel
Step 3 –Step 2 –
Connection Overview
Minimum Required Connections
Caution: Incorrect wiring may cause permanent damage
Wire the badge reader and Access Control system as required for your installation
For installations that require 1-Wire LED control, connect the ORANGE wire (Panel
LED Green) to the LED terminal on the panel
Attach wall plate to 2-gang box with provided screws, paying attention to
point the arrow towards door
Installed screw heads must be flush to the wall plate. Protruding screw
heads will cause interference when installing the Rock onto the wall plate
Use edge of tunnel to level wall plate
Arrow towards door
PoE+ Ethernet
Wiring harness
Alcatraz
Rock
Shielded
Cat5e/Cat6
Badge
Reader
Badge
Reader
Access
Control
Panel
Access
Control
Panel
PoE+ Ethernet
Wiegand/OSDP Cable
RED
BLACK
GREEN
WHITE
+12v
GND
D0
D1
+12v
GND
D0
D1
LED Green
RED
BLACK
GREEN
WHITE
ORANGE
PoE+ input power: 42-57 VDC 0.5A
Refer to enclosed Installation Guide part number 541-0001-00-00 Rev 01 for Wiring Diagram.
Alcatraz AI, inc.

Attach Alcatraz Rock to wall platePlug in and retain cables
Step 5 –Step 4 –
To remove Rock from wall plate, press spring pin hidden behind the vent mesh
Press and snap Rock onto installed wall plate
Spring Pin Release
Included cable ties
Cable ties secured
and trimmed
Cable tie
attachment point
Pre-loop cable
ties to post
The Rock has TAMPER detection: Removal of Rock from wall plate
will result in TAMPER signal assertion to ACS
To complete the Installation and onboarding please refer to the
User Guide (see QR code on back cover)

ROCK-1 ALCATRAZ FACIAL AUTHENTICATION
ACCESS CONTROL DEVICE
Part Number S10-0001
Input Voltage PoE+ (42.5 – 57.0 VDC)
Current 0.5A
Operating Temp -20º – 66ºC (-4º – 150ºF)
Humidity Relative humidity 10-90% non condensing
Weight 709g (1lb 9oz)
Size W 13.2cm (5.2”) x H 12.2cm (4.8”) x D 8.3cm (3.3”)
FCC
CE Marking
UL Marking
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could
void your authority to operate this equipment.
Alcatraz AI hereby declares that these facial authentication devices are in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Security, facial authentication and access control features and any other features related to that of the
product have not been evaluated.
WARNING: This product can expose you to chemicals including DINP, which is known to the
State of California to cause cancer, and DIDP, which is known to the State of California to cause
birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
©2020 Alcatraz AI, Inc., All rights reserved
Support:
1 [phone]
support.alcatraz.ai
Alcatraz AI, Inc.
1808 El Camino Real
Redwood City, California 94063
541-0001-00-00 www.alcatraz.ai Scan for User Guide