Cantel Medical MEDIVATORS 2-8-650HAN Instruction Manual

Locate the endoscope port and follow the instructions for attaching the
corresponding Endoscope Connector. All connectors must be attached.
Air/Water Connector
Align the connector with
the air/water bottle port and
push to fully engage.
2-8-650HAN/2-8-650CAS HOOKUP CONNECTION GUIDE
Using MEDIVATORS®ADVANTAGE™ Automated Endoscope Reprocessors
Leak Test Connector
Align the slot on connector with the
pin on the scope. Push on and turn
clockwise to engage. To remove
leak test connector, turn connector
counter-clockwise until slot is
aligned with pin and pull off. Do not
pull until slot is aligned with pin.

READ ALL INSTRUCTIONS PRIOR TO CONNECTION
Port ID Port Name Connector Assembly Description Order Number
1LEAK TEST Leak Test Connector Assembly H28650-1
2JET/AUX Air/Water Connector Assembly H28650-26
3BIOPSY Biopsy Inlet Connector Assembly H28650-3
4AIR Air Probe Connector Assembly H28650-4
5ELEVATOR Forward Water Jet Connector Assembly H28650-5
6WATER Air/Water Connector Assembly H28650-26
7SUCTION Suction Connector Assembly H28650-7
ANA Air/Water, Suction Channel Plug N/A
If a Connector Assembly needs replacement, locate the port number/name and use
the corresponding order number found in the Connector Assembly Identication Chart.
Connector Assemblies are specic to individual hookups. Check each Hookup Connection
Guide for relevant information.
Each Advantage Hookup is comprised of multiple ports and connector assemblies. Each
port is labeled with a Port ID number (circled). This same number also identies the
corresponding Connector Assembly. Each Connector Assembly is tted with a specic
endoscope connector. (see Fig. 2).
EXAMPLE CONNECTOR ASSEMBLY (Figure 2)
CONNECTOR ASSEMBLY IDENTIFICATION CHART
Ferrule Endoscope
Connector
example
Tubing
Connector
Coupling
Label
ADVANTAGE HOOKUP AND CHANNEL SEPARATOR (Figure 1)

Biopsy Inlet Connector
Align the biopsy connector
disc over the biopsy inlet
and push down to compress
spring and slide the frame
forward to fully engage.
Air Probe Connector
Align with air probe, push
and slide until fully engaged.
Suction Connector
Align silicone tubing with suction
barb and push tubing onto barb
until fully engaged.
Air/Water, Suction
Channel Plug
Align and attach Peer
Medical channel plug
(supplied with endoscope)
to air/water and suction
ports. Insert and close
clamp to secure. Ensure
that luer caps are tted
and secure.
A
Forward Water Jet Connector
Align stainless steel tting with forward
water jet port, push and turn clockwise
to connect.
LOT: XXXXXX ID: xxxX
P/N: X-X-XXXHAN





Ensure proper alignment of all connectors with the
endoscope mating parts prior to attachment.
If you have any questions regarding this hookup, in the U.S., please contact MEDIVATORS Technical Support at
1-800-444-4729. Outside the U.S., please contact your MEDIVATORS Distributor.
DESIGNATED HOOKUP FOR THE FOLLOWING ENDOCHOICE® ENDOSCOPES*:
C38s C38s-133 C38s-150 CS-1001 F1C-133 F1C-150 FUSE-1C FUSE-1G FUSE-F1C FUSE-G32
* This list of corresponding endoscope models is subject to change without notice. For a full list, please go to:
www.medivators.com/hookuplookup
© 2016 Medivators Inc. 50098-562/B
Representative endoscope for illustrative purposes only. For exact
.port locations, refer to endoscope manufacturer’s instruction guide.
Forward Water Jet Cleaning
Adapter Gas 2426
This is an optional piece
Air/Water, Suction
Channel Plug Gas 2393
ADDITIONAL REQUIRED ENDOSCOPE CONNECTIONS

Medivators BV
Sourethweg 11
6422PC Heerlen
The Netherlands
Tel: [phone]
Cantel Medical Asia/Pacic Pte. Ltd.
1A International Business Park
#05-01 Singapore 609933
Tel: [phone]
www.medivators.com
Manufactured in the USA by:
Medivators Inc.
14605 28th Avenue North
Minneapolis, MN 55447 USA
Toll Free: +1.800.444.4729
Cantel Medical Devices (China) Co. Ltd.
Unit 804-805, Innov Tower Block A,
Hongmei Road, Xuhui 200233 Shanghai
Tel: [phone]
Fax: [phone]
HOOKUP CONNECTOR BLOCK LABEL
The Hookup Connector Block Label contains useful information for quick reference.
Handle Locking Instructions - insert block onto basin channel manifold and move handle
to the left to lock. Move to the right to unlock.
Lot Number - identies date of manufacture.
Hookup Part Number - identies hookup.
Hookup Barcode - barcode of part number.
Port Name - identier of port location in ADVANTAGE system. Error logs identify issues using
these names. Also identier of Connector Assembly replacements for older model hookups.
Port ID Number - identier for Connector Assembly replacements. Not found on older
model hookups.
Alternative Channel Connector Names - connector names vary depending on specic
endoscope channel conguration.
WARNINGS & CAUTIONS
This hookup is intended for connection only with the specic endoscope models
identied in the appropriate MEDIVATORS online hookup guide. Use of this hookup
with endoscopes other than those specied by the hookup application guide may
result in inadequate HLD.
Users operating MEDIVATORS AERs and hookups must be trained and competent in
the understanding of endoscope channel systems.
Prior to reprocessing, users must verify that the hookup used contains connections
for all appropriate channels that require a separate reprocessing connection
according to the hookup instructions
All connectors and adapters must remain rmly attached and unrestricted for the
entire disinfection cycle to ensure adequate HLD. Users must inspect the endoscope
and hookup combination to verify proper connection and ow.
Modications or repairs to hookups which do not correspond to the manufacturer’s
specications may result in inadequate HLD and/or damage to endoscopes.
Failure to properly clean and prepare endoscope for immersion prior to hookup
connection may result in inadequate HLD and/or damage to the endoscope.
Endoscopes must be inspected for damage and veried to be in proper working
order prior to hookup connection. Connection of hookups to damaged endoscopes
or endoscopes with obstructed/restricted channels could result in inadequate HLD.
Manual leak testing must be carried out in accordance with manufacturer’s
recommendations prior to reprocessing.
Install all necessary waterproof caps, plugs and cleaning adapters prior to
immersion.
Do NOT autoclave MEDIVATORS hookups.
MEDIVATORS makes no claim on high-level disinfection efcacy when these
reprocessing instructions are not followed, or when this hookup kit is applied to
endoscopes other than those specied in the online interactive hookup guide.
Avoid biological contamination. Always wear personal protective equipment when
handling endoscopes.
© 2016 Medivators Inc. 50098-562/B
CASSETTE-STYLE HOOKUPS (not available in US)
An ADVANTAGE Hookup Cassette combines an endoscope tray with the hookup connector
block. Specic endoscope connections for this hookup are identical to non-cassette
versions. Cassette-style hookup part numbers are designated with a CAS sufx.
ADVANTAGE Hookup Cassettes are available outside the United States only. Connector
Assemblies are listed in the Connector Assembly Identication Chart.
LOT: XXXXXX ID: XXXX
P/N: X-X-XXXHAN
Hookup Part Number
Hookup
Barcode
Port ID
Number
Port Name
Alternative
Channel
Connector
Names
Handle Locking
Instructions
Lot Number
ADVANTAGE™and MEDIVATORS®are trademarks and registered
trademarks of Medivators Inc.