Care of Sweden CuroCell S.A.M. PRO User manual

User Manual
2018-10-17
CuroCell S.A.M.® PRO
Static Antidecubitus Mattress
Item number user manual: 95-001410-EN0000

2
Contents
Important safety instructions 3
Introduction 4
Product description 5
Installation and start-up 8
Cleaning and reconditioning 10
Storage 11
Maintenance 12
Troubleshooting 13
Technical description 14
Spare parts 16
Options and accessories 18
Warranty 19
Other information 20
Your own notes 21

3
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions prior to use
WARNING! To minimise the risk of fire, electric shock or bodily injury:
1. The product must only be used for its intended purpose as described in this manual.
The product may not be combined, assembled or repaired with other parts (e.g. pump
and mattress), accessories or spare parts other than those described in this manual or
other documentation from Care of Sweden.
2. Do not use the pump in wet rooms where there is a risk of the pump coming into
contact with water or another liquid. Never handle a pump that has come into contact
with water/liquid. Pull the plug out of the electrical socket immediately and send the
product to an authorised service technician for servicing.
3. DO NOT USE in the vicinity of or in contact with fire sources/hot surfaces, such as fire,
burning cigarettes or hot lamps. Although the product has undergone fire testing, it
could become damaged if it comes into contact with fire sources.
4. Position and use the product in a manner that prevents it from becoming trapped or
damaged. NOTE: Be particularly aware of trapping damage the risk of crush injuries
when using bed rails.
5. Never use the product if the pump power cord or plug is defective, the pump casing is
damaged or it is not functioning properly. Contact an authorised service technician for
examination and repair.
6. Regularly check product functionality through a “hand check” (see section 3.4). Also
check that the comfort setting is correct as indicated in the table on the pump.
7. Continual monitoring is required when the product is used for individuals needing
special supervision, such as children.
8. The mattress is protected by a hygiene cover; Please try to avoid the simultaneous use
of multiple hygiene cover with this mattress. Because the risk of vapour permeability
can be destroyed.
9. The hygiene cover does not allow liquid or air to penetrate, but is vapour permeable
(vapour is wicked away). Make sure that the patient is positioned correctly to avoid
the risk of suffocation.
10. Prevent damage to the hygiene cover from sharp objects.
11. If the cover is equipped with handles on the long sides, these handles are only to be
used for lifting and moving the mattress itself. All other use will be at your own
responsibility and is not covered by the product warranty.
12. The pump’s power cord should be positioned to minimise the risk of tripping; use a
cable holder if possible.
13. There is a risk of suffocation if the power cord accidentally ends up around the user’s
neck; if possible use a cable holder and make sure that the patient is lying correctly on
the bed according to the instructions.

4
1. Introduction
CuroCell S.A.M.® PRO is a static air mattress that can be used in all kinds of caring
environments and it is very functional and cost effective.
Always read the user manual prior to use.
1.1 General information
This system is a medical device with CE marking in accordance with MDD 93/42/EEC. According
to statutory regulations made by the authorities regarding medical devices, the manufacturer
is required to report all accidents or incidents involving their products. We would be very
grateful for all information involving accidents or incidents relating to our products, by
reporting them immediately to us, here at Care of Sweden.
This system has been tested and approved according to the following standards: EN 60601-1,
SS-EN ISO 12182, SS-EN ISO 14971, SS-EN ISO 10993, EN 597-1, EN 597-2 and EN 14126.
1.2 Intended use
CuroCell S.A.M.® PRO can be used in all types of medical environments and is intended to
assist in the prevention and treatment of pressure ulcers, up to category 3(1). The system can
also be used as an aid in pain therapy. CuroCell S.A.M.® PRO is a static air mattress system
designed for continuous use.
1.3 Variants
The product is available as a mattress overlay (CuroCell S.A.M.® PRO, CuroCell S.A.M.® PRO
CF10) to be placed on top of an existing mattress or as a combi mattress (CuroCell S.A.M.® PRO
CF16), with an integrated foam core, that is placed directly on the bed base.
The recommended user’s weight for this system is up to 250 kg.
We recommend that position changes are made regularly. The time interval must be assessed
by the responsible personnel, depending on user’s status, diagnostic and general condition.
The mattress must always be cleaned between users.
(1) National Pressure Ulcer Advisory Panel, European Pressure Ulcer Advisory Panel and Pan Pacific Pressure Injury
Alliance. Prevention and Treatment of Pressure Ulcers: Quick Reference Guide. Emily Haesler (Ed.). Cambridge Media:
Osborne Park, Western Australia; 2014.
NOTE:
•When used together with positioning pillows, read the pillow user manual carefully for
correct positioning of the user.
•If you are using this product with an evacuation sheet, it is the user’s responsibility to
ensure that it is safe to use for evacuation.
•Remember that the underlying mattress is important for the product’s functionality.
•The mattress is unsuitable for X-ray examinations because of the risk of blurred images
or artefacts that may lead to diagnostic errors.
•Do not store or use the product in direct sunlight. The product may be damaged by the
elevated temperature and UV light.

5
1.4 Other information
Action plan for pressure ulcers
To achieve the best possible result for this product it is recommended that a well-planned and
well-structured working environment be used. In our guideline "Action plan" you will find
examples which can be applied and put into practice when using our products.
The Mattress Guide
This practical guide gives you as a care giver, help in choosing the correct mattress from the
Care of Swedens range. CuroCell S.A.M® is a mattress in function group B. This information can
be found on our website www.careofsweden.com or you can order a copy from our Customer
services by sending your details to [e-mail].
2. Product description
2.1 Pump – Front
1. Comfort setting knob.
2. Control panel.
3. Casing, front.
4. Tube connector.
5. Power cord connector.
6. Power switch.
Used to turn the pump on or off. A green
light indicates when the pump is on.
7. Casing, back.
A. Hangers
B. Fuses (2 x T1A/250 V).
C. Label.
D. Air filter.

6
2.2 Pump functions – Control panel
Comfort setting knob – Comfort settings
The comfort setting knob adjusts the air pressure in the mattress. When the
knob is turned clockwise, the air supply and pressure in the mattress increase.
When the knob is turned counter clockwise, the air supply and pressure in the
mattress decrease.
For sitting positions, we recommend that the pressure be raised by +25 kg. Check
using a hand check (see section 3.4).
Maximum pressure (Nursing mode)
With this function, the entire mattress is inflated and provides fixed support. This
function should be used when nursing the patient, shifting the patient’s position
or moving the patient in or out of bed. This function automatically reverts to the
previous setting after about 30 minutes.
Information signal
If the mattress pressure is too low an audio-visual alarm is triggered.
Turning off the information signal
Turn off the audio alarm by pressing the Audio off button. The audio alarm is re-
activated after seven minutes if the pressure has not returned to normal.
In the event of problems with notifications, see section 7 for troubleshooting.
Normal pressure
The light shows steady when the mattress is ready to be used. It flashes when air
is being pumped into the mattress.

7
2.3 Mattress
1. Cells/air bladder 2. Tubes 3. Tube holder 4. CPR (Rapid deflation)
2.4 Other parts
Hygiene cover
Inner cover Soft (accessory CuroCell S.A.M.® PRO)
Transport and Storage Bag (accessory)
Integrated foam core (only CuroCell S.A.M.® PRO CF16)

8
3. Installation and start-up
3.1 Installation
When unpacking, check that no parts are damaged. If any damage is found, contact Care of
Sweden before using the product.
1. Place the mattress on top of an existing mattress. If possible, secure it by pulling the elastic
straps on the bottom over the corners of the underlying mattress.
Note: If the mattress has an integrated foam core (CuroCell S.A.M.®PRO CF16), place the
mattress directly on the bed base. Secure the mattress to the moving parts of the bed base
using the straps on the cover.
2. Hang the pump by the foot end of the bed or place it on a flat, sturdy surface. Place the
power cord so there is no risk of stumbling over it, run it over with the bed wheels or getting it
jammed when raising or lowering the bed.
3. Connect the air tubes coming from the mattress to the side of the pump. The pump and
hoses are equipped with quick connectors; an audible “click” will be heard when these have
been connected correctly.
4. Check to make sure that the power is set to “0” (off). Plug the power cord into an
approved outlet (110 or 220 V depending on the country and the voltage level).
3.2 Start-up and settings
PLEASE NOTE: Always read the user manual prior to use.
1. Start the pump by pressing “1” (on), on the side of the pump.
2. The pump starts filling the mattress with air. The green light with the symbol will flash
during the inflation phase; it takes about 15 minutes for the mattress to fill with air.
3. When the symbol shows a steady green light, the mattress is ready to be used.
3.3 Comfort settings
The air pressure in the mattress can be adjusted according to the user’s comfort preference.
Always consult the prescriber or other authorised personnel for the appropriate setting.
Appropriate air pressure is selected using the knob (0–250 kg). The numbered scale guides
your selection. For sitting positions, we recommend that the pressure be raised by +25 kg.
Check using the hand check (see section 3.4).
NOTE:
•Make up the bed with sheets to increase user comfort.
•Check that the CPR valve is closed.
•Make sure that the mattress is the correct size for the bed.

9
3.4 Hand check, checking the set pressure
Hand check is used to ensure that the mattress is working
properly. This should be done regularly, once per shift, after
changing the position in the bed or changing the comfort
setting.
Open the cover. Place a flat hand under the air cells directly
underneath the user’s pelvic region and make sure that the
user does not lay directly on the underlying mattress. We
recommend that there should be about a finger’s thickness to
the underlying mattress.
If the margin is too great or too small, you need to increase or decrease the comfort settings to
the next highest or lowest step. Wait 10 minutes and perform a new hand check.
3.5 CPR
In case of an emergency where CPR (cardiopulmonary resuscitation) is
necessary: Quickly pull the CPR strap on the air tubes between the pump
and the mattress. Detach the quick connectors on the side of the pump,
for even faster deflation.
NOTE: Make sure that the CPR connector is properly connected after use.
3.6 Low pressure
If there is abnormally low air pressure, see section 7 for Troubleshooting.
3.7 Transport function
Detach both the tubes from the pump and connect these together; this will put the mattress in
“Transport mode”. We recommend that this function only be used for a short period of time.
NOTE:
•When the head end of the bed is raised, the pressure should be increased by 25 kg.
•When only part of the mattress is under load, e.g. for amputee users, the pressure
should be increased (by 1–2 steps). Then perform a hand check (see section 3.4).
•The recommended user weight is up to 250 kg.
Note:
If the air pressure remains low, search for damage on the mattress and the tubes. Repair
when needed or contact the supplier.

10
4. Cleaning and reconditioning
It is important to follow the instructions below before the product is used for another user.
Consult your hygiene manager or the supplier for help and instructions if you are unsure.
4.1 Cleaning
PUMP
Wipe off the pump with a damp cloth and a mild cleaning solution for this purpose
such as: alcohol with or without tensides, Isopropanol 70 %, oxidating solutions or
chlorine max 1 %. If using a different agent, choose one that does not affect the plastic
of the pump housing.
MATTRESS COVER
Covers can be wiped off with a mild cleaning solution for this purpose such as: alcohol
with or without tensides, Isopropanol 70 %, oxidating solutions or chlorine max 1 %.
Excrements and blood spots must be removed immediately with cold water. Carefully
follow local instructions and usage instructions for the cleaner.
Multi-layer covers should be divided before washing. The various parts should be washed with
similar colours.
Chlorine and phenol-based cleaners could have a negative impact on the PU surface
and should be avoided. If chlorine is used, we recommend a mixture of max. 1%.
INNER COVER SOFT (accessory)
Clean the affected area with a mild cleaning solution for this purpose such as: alcohol with or
without tensides, Isopropanol 70 %, oxidating solutions or chlorine max 1 %.
WARNING!
Do not open the pump housing – risk of electric shock. Service and maintenance must be
performed by authorised technicians. Do not get the pump wet or submerge it in any
liquid.

11
4.2 Reconditioning
PUMP
See section 4.1 for instructions.
MATTRESS
1. Disconnect the tubes from the pump and deflate the mattress. Also open the CPR valve.
2. Remove the cover. For more information on cleaning covers, see section 4.1. If the product
is equipped with a foam core it should be removed and cleaned separately.
3. Move the mattress to a clean area that is suitable for cleaning.
4. Wipe off the cells, all tubes and the CPR valve with a mild cleaning solution for this purpose
such as: alcohol with or without tensides, Isopropanol 70 %, oxidating solutions or chlorine
max 1 %.
5. Wipe off and disinfect all the work surfaces with an alcohol based cleaning agent intended
for this purpose.
6. Put the mattress together. If the tubes have for any reason come loose from the cells, these
must be reattached according to the illustration in section 2.3. Close the CPR valve.
FOAM CORE (CuroCell S.A.M.® PRO CF16)
Clean the affected area with a mild cleaning solution for this purpose such as: alcohol
with or without tensides, Isopropanol 70%, oxidating solutions or chlorine max 1 %.
Gently squeeze out any water. NB: Do not wring or roll the cushion to extract water. Let the
cushion dry in a warm, ventilated area (not in direct sunlight). The cushion must be completely
dry before it is used again.
5. Storage
It is advisable to store the mattress and pump in the product bag (accessory). Place the pump
so that it is protected by the mattress. Handle the stored product with care. Do not place any
heavy objects on top of it. The pump should be stored in a dry environment indoors and out of
direct sunlight.
NOTE:
Check the hygiene cover each time the product is cleaned. If damaged, it must be
replaced or repaired. Also check the pump, tube connectors and power cord during
cleaning. Damaged parts must be replaced or repaired.

12
6. Maintenance
1. Check the power cord and plug for damage and scratches.
2. Check the mattress cover to make sure it is undamaged and that covers and cells are
correctly assembled.
3. Check that air is coming from the outlets on the side of the pump.
4. Check that no tubes or connectors are damaged or pinched.
Contact the manufacturer or your local dealer for spare parts.
6.1 Air filter and fuse
replacement
Air filter (A):
1. Loosen the small protective plate on
the rear of the pump using a
screwdriver.
2. Remove the filter from the holder.
3. Insert the new filter in the holder,
put the protective plate back in place
and secure using the screws.
Fuses (B):
1. Use a screwdriver to remove the
fuse holder.
2. Replace the old fuse with a new one
marked T1A/250 V; note that there are
two fuses.
3. Use a screwdriver to put the fuse
holder back in place.
B
A

13
7. Troubleshooting
The pump does not start Check that the power cord is connected to a socket.
Check that all fuses are OK.
Pump is operating but Check that air is coming from the pump and that
the mattress is not inflating the power cord is connected correctly. If the pump is working
normally but no air is coming out, the pump should be serviced.
Check that the CPR valve is closed.
Check that the mattress and the mattress connector are not
damaged.
Check that the tubes are intact.
Check that the air filter is not blocked.
The user sinks The comfort settings might be incorrectly set. Adjust the
Pressure (is lying directly on the mattress) and wait a few
minutes. Check again using the “hand check” (see section 3.4).
Check that the CPR valve is closed.
Mattress not stationary Check that the mattress is secured to the underlying mattress
with the elastic straps or, if the mattress has an integrated
foam core (CuroCell S.A.M.® PRO CF16), secured with the
straps to the moving parts of the bed base.
Noisy pump, Check that the pump is correctly attached to the bed.
or vibrations can be felt Resonance may occur in parts of the bed. Remove the pump
and listen to see whether there’s any difference. This can be
fixed by placing the pump on a level, sturdy surface. Or by
putting, for instance, a towel between the pump and the
bed.
If your questions are not answered by the above information, please contact Care of Sweden
or your local dealer for further assistance.
Problem Solution

14
8. Technical description
8.1 Technical specification
PUMP
SPECIFICATION
Model
CuroCell S.A.M.® PRO
Voltage
110-120 V, 60 Hz, 220-240 V, 50Hz
Current
Max 10 W
Fuse type
T1AL, 250 V
Dimensions (LxWxH)
26 x 8 x 13 cm
Weight
1.5 kg
Sound level
<28 dB
Ambient environment
Temperature
Operation: 5 °C ˜ 40 °C
Storage: -25 °C ˜70 °C
Shipping: -25 °C ˜70 °C
Humidity
Operation & Transport: 5 % ˜95 % non-condensing
Storage: 10 % ˜80 % non-condensing
Atmospheric pressure
Operation: 700 hPa to 1060 hPa
Storage & Transport 500 hPa to 1060 hPa
Classification
Class II, Type BF, IP21
MATTRESS
SPECIFICATION
Model
CuroCell S.A.M.® PRO/CuroCell S.A.M.® PRO
CF10/CuroCell S.A.M.® PRO CF16
Dimensions (WxLxH)
80/85/90/105/120x200/210x10/16 cm
Weight
2.6 kg (85x200 cm) / 8.1 kg (85x200 cm)
NB: The manufacturer can at any time change the specifications for the product.
8.2 Labelling
The mattress is labelled with product name production date, article number, size, care and
wash instructions, EAN-bar code, as well as space for own labelling. The product also displays
which side is up/down and head/foot.
WARNING!
Follow the operation and maintenance instructions carefully in order to prevent bodily
injuries, as well as damages to the product or other equipment.

15
8.3 Symbol key
Type BF
Class II equipment
(Double
-insulated)
The mattress should be
used with the user lying in
the lengthwise direction
Recycling
Read the user manual
CE-marked in acc. to
MDD 93/42/EEC
Placed directly on the
bed base
Recommended user weight
Patient information
–
category
Year-Month-Day
Article number
XXXX-XX-XX
Group of function
Manufacturer
Do not dispose of with
household waste; follow
recycling instructions
Foot placement
Drip dry
Do not tumble dry
Do not dry clean
Chlorine
Machine wash at 70 °C
Machine wash at 95 °C
Tumble dry
Place on top of
existing mattress
Do not iron
Wipe off
Counteract shear force
Do not machine wash
IP code (ingress
protection rating)
Heel function (Described as
“Heel function” text on the
cover)
Can be rotated
Can be turned
Warning of electrical
voltage

16
9. Spare parts
Cover Steel for Cover Steel for Cover Stone for
CuroCell S.A.M. PRO CuroCell S.A.M. PRO CF10 CuroCell S.A.M. PRO CF10
Size Art. no. Art. no. Art. no.
80x200 cm SC201-080200-SE0000 SC220-080200-SE0000 SC221-080200-SE0000
80x210 cm SC201-080210-SE0000 SC220-080210-SE0000 SC221-080210-SE0000
80x220 cm SC201-080220-SE0000 SC220-080220-SE0000 SC221-080220-SE0000
85x200 cm SC201-085200-SE0000 SC220-085200-SE0000 SC221-085200-SE0000
85x210 cm SC201-085210-SE0000 SC220-085210-SE0000 SC221-085210-SE0000
85x220 cm SC201-085220-SE0000 SC220-085220-SE0000 SC221-085220-SE0000
90x200 cm SC201-090200-SE0000 SC220-090200-SE0000 SC221-090200-SE0000
90x210 cm SC201-090210-SE0000 SC220-090210-SE0000 SC221-090210-SE0000
90x220 cm SC201-090220-SE0000 SC220-090220-SE0000 SC221-090220-SE0000
100x200 cm SC201-100200-SE0000 SC220-100200-SE0000 SC221-100200-SE0000
100x210 cm SC201-100210-SE0000 SC220-100210-SE0000 SC221-100210-SE0000
100x220 cm SC201-100220-SE0000 SC220-100220-SE0000 SC221-100220-SE0000
105x200 cm SC201-105200-SE0000 SC220-105200-SE0000 SC221-105200-SE0000
105x210 cm SC201-105210-SE0000 SC220-105210-SE0000 SC221-105210-SE0000
105x220 cm SC201-105220-SE0000 SC220-105220-SE0000 SC221-105220-SE0000
120x200 cm SC201-120200-SE0000 SC220-120200-SE0000 SC221-120200-SE0000
120x210 cm SC201-120210-SE0000 SC220-120210-SE0000 SC221-120210-SE0000
120x220 cm SC201-120220-SE0000 SC220-120220-SE0000 SC221-120220-SE0000
Top part Olivia for Top part Stone for Bottom part CuroCell for
CuroCell S.A.M. PRO CF16 CuroCell S.A.M. PRO CF16 CuroCell S.A.M. PRO CF16
Size Art. no. Art. no. Art. no.
80x200 cm ST101-080200-SE0000 ST102-080200-SE0000 SB101-080200-SE0000
80x210 cm ST101-080210-SE0000 ST102-080210-SE0000 SB101-080210-SE0000
80x220 cm ST101-080220-SE0000 ST102-080220-SE0000 SB101-080220-SE0000
85x200 cm ST101-085200-SE0000 ST102-085200-SE0000 SB101-085200-SE0000
85x210 cm ST101-085210-SE0000 ST102-085210-SE0000 SB101-085210-SE0000
85x220 cm ST101-085220-SE0000 ST102-085220-SE0000 SB101-085220-SE0000
90x200 cm ST101-090200-SE0000 ST102-090200-SE0000 SB101-090200-SE0000
90x210 cm ST101-090210-SE0000 ST102-090210-SE0000 SB101-090210-SE0000
90x220 cm ST101-090220-SE0000 ST102-090220-SE0000 SB101-090220-SE0000
100x200 cm ST101-100200-SE0000 ST102-100200-SE0000 SB101-100200-SE0000
100x210 cm ST101-100210-SE0000 ST102-100210-SE0000 SB101-100210-SE0000
100x220 cm ST101-100220-SE0000 ST102-100220-SE0000 SB101-100220-SE0000
105x200 cm ST101-105200-SE0000 ST102-105200-SE0000 SB101-105200-SE0000
105x210 cm ST101-105210-SE0000 ST102-105210-SE0000 SB101-105210-SE0000
105x220 cm ST101-105220-SE0000 ST102-105220-SE0000 SB101-105220-SE0000
120x200 cm ST101-120200-SE0000 ST102-120200-SE0000 SB101-120200-SE0000
120x210 cm ST101-120210-SE0000 ST102-120210-SE0000 SB101-120210-SE0000
120x220 cm ST101-120220-SE0000 ST102-120220-SE0000 SB101-120220-SE0000

17
Air cells incl. tubes with CPR and quick connector
Art. no. Size Art. no. Size
CC-250900 80x200 cm CC-250909 100x200 cm
CC-250901 80x210 cm CC-250910 100x210 cm
CC-250902 80x220 cm CC-250911 100x220 cm
CC-250903 85x200 cm CC-250912 105x200 cm
CC-250904 85x210 cm CC-250913 105x210 cm
CC-250905 85x220 cm CC-250914 105x220 cm
CC-250906 90x200 cm CC-250915 120x200 cm
CC-250907 90x210 cm CC-250916 120x210 cm
CC-250908 90x220 cm CC-250917 120x220 cm
Art. no. Description
SP103-EN0000 Mattress pump CuroCell S.A.M. PRO (110-120 V)
SP101-SE0000 Mattress pump CuroCell S.A.M. PRO (220-240 V)
CC-908060 Tube set CuroCell S.A.M. PRO, 200 cm
CC-908061 Tube set CuroCell S.A.M. PRO, 210 cm
CC-908062 Tube set CuroCell S.A.M. PRO, 220 cm
If other spare parts are needed, please contact Care of Sweden or your local dealer for further
assistance.

18
10. Options and accessories
10.1 Options
Inner cover Soft
Enhances the comfort further, can also be used for very sensitive users. This is included for
CuroCell S.A.M.® CF10 and CuroCell S.A.M.® CF16. Place the air cells inside the cover with the
soft foam side up.
Sturdy transport bag
Transportation and storage bag.
Mattress cover
With welded seams.
10.2 Accessories
Inner cover CuroCell S.A.M. PRO CF10 Inner cover CuroCell S.A.M. PRO CF16
Size Art. no. Art. no.
80x200 cm SI101-080200-SE0000 SI120-080200-SE0000
80x210 cm SI101-080210-SE0000 SI120-080210-SE0000
80x220 cm SI101-080220-SE0000 SI120-080220-SE0000
85x200 cm SI101-085200-SE0000 SI120-085200-SE0000
85x210 cm SI101-085210-SE0000 SI120-085210-SE0000
85x220 cm SI101-085220-SE0000 SI120-085220-SE0000
90x200 cm SI101-090200-SE0000 SI120-090200-SE0000
90x210 cm SI101-090210-SE0000 SI120-090210-SE0000
90x220 cm SI101-090220-SE0000 SI120-090220-SE0000
100x200 cm SI101-100200-SE0000 SI120-100200-SE0000
100x210 cm SI101-100210-SE0000 SI120-100210-SE0000
100x220 cmSI101-100220-SE0000 SI120-100220-SE0000
105x200 cm SI101-105200-SE0000 SI120-105200-SE0000
105x210 cm SI101-105210-SE0000 SI120-105210-SE0000
105x220 cm SI101-105220-SE0000 SI120-105220-SE0000
120x200 cm SI101-120200-SE0000 SI120-120200-SE0000
120x210 cm SI101-120210-SE0000 SI120-120210-SE0000
120x220 cm SI101-120220-SE0000 SI120-120220-SE0000
Art. no. Description
CC-9091 Transportation and storage bag for CuroCell S.A.M.® PRO
CC-9093 Transportation and storage bag for CuroCell S.A.M.® PRO CF10
58-900909 Transportation and storage bag for CuroCell S.A.M.® PRO CF16
10.3 Other accessories
To ensure the best level of comfort, we recommend the use of accessories from Care of
Sweden since our products are designed to work well together. If you require any accessories,
or for more information about our products, please contact Care of Sweden or visit our
website – www.careofsweden.com.

19
11. Warranty
11.1 Scope
This CuroCell® system is covered by a 2-year warranty for manufacturing defects. The warranty
does not apply to normal wear and tear or damage due to negligence or improper
handling/care.
11.2 Service and maintenance
This CuroCell® mattress is a medical device, in accordance with MDD 93/42/EEC, that is used
as an aid in preventing and treating pressure ulcers. For this reason, we recommend that the
product be regularly serviced and inspected to maintain functionality and performance. Like
other technical devices, a pump that is properly cared for works better and lasts longer.
During the expected lifespan of the product, some parts of the pump will experience wear and
will require servicing by a certified service technician in order to retain good functionality and
performance. The scope of the servicing and the servicing intervals will depend on how often
and to what degree the product is used.
Service and maintenance must always be performed by Care of Sweden or one of its
authorised technician. Only use spare parts that have been approved by Care of Sweden. Use
of non-approved spare parts invalidates the warranty.
Faults and defects regarded as warranty faults are rectified free of charge. A warranty claim
must be submitted to Care of Sweden before the product is returned.
11.3 Life span
The expected life span of the mattress is 5 years.

20
12. Other information
12.1 Disassembly and recycling
Except for certain parts of the pumps, energy recovery is possible for almost all material in
CuroCell®products through incineration in waste incineration facilities.
Pump: A used CuroCell®pump must not be disassembled. Instead it should be taken to a
recycling centre. The product is sorted as “electronic waste”.
Mattress: A used CuroCell®mattress should be taken to a recycling centre. The product is
sorted as “combustible waste”.
For more information, please contact Care of Sweden or your local dealer.
12.2 Returns and warranty claims
Contact Care of Sweden before returning the product. The return postage will be paid by Care
of Sweden if the fault is covered by the product warranty, otherwise by the customer.