Carnival King 4 oz. User manual

Popcorn Carts
www.CarnivalKingSupplies.com
user manual
11/2019

2
www.CarnivalKingSupplies.com .||||| [e-mail]
popcorn carts for 4 oz. & 8 oz. poppers
General Safety Precautions
1. This manual will outline safety warnings and precautions, and assembly. The warnings and instructions reviewed
in this manual cannot cover all possible conditions and situations that may occur. Factors such as caution and
common sense cannot be built into this product and it is trusted the operator will follow these measures.
2. This cart must never be modified and should only be used for its intended purpose.
3. Use a protective covering for the cart when long-term storage is planned.
4. Avoid using outdoors. In the circumstance that the cart is used outdoors, ensure it is protected from rain and water.
5. When cleaning, do not use abrasive chemical or materials as you will damage the cart’s surface.
Cart Parts List
A. Main unit (1) (sold separately)
B. Popping pot (1) (sold separately)
C. Working platform (1)
D. Hand rail (1)
E. Square pole (2)
F. Long stand (1)
G. Short stand (1)
H. Wheel axle (1)
I. Wheels (2)
J. Storage cabinet (1)
K. Parts box which includes
a. Package A (plated bolts/nuts/washers [8 each])
b. Package B (bolts/washers [8 each])
c. Package C (metal sleeves/nuts with round cap/
washers [2 each])
d. Package D (wrench [2])
4 oz. Popcorn Cart Specs
8 oz. Popcorn Cart Specs
Unit Dimensions 27 ⅝"L x 19"D x 36 ⅝"H
Rear Wheels 16"
Unit Dimensions 30"L x 21"D x 36"H
Rear Wheels 18"

3
www.CarnivalKingSupplies.com .||||| [e-mail]
popcorn carts for 4 oz. & 8 oz. poppers
Cart Assembly
1. Connect the long stand (F) and the 2 piece square pole (E) together using the bolts and washers from Package B.
2. Connect the result of Step 1 with the short stand (G) by using the bolts and washers of Package B.
3. Attach the axle (H) into the short stand (G). Mount wheels (I) on the ends of the axle (H). Secure the wheels by
using the contents of Package C. Place washers on each side of the wheels (I) and then put on the round cap nuts
and secure with the wrenches provided in Package D.
4. Turn the storage cabinet (J) upside down. Attach the short and long stands onto the bottom of the cabinet (J) and
secure by bolts from Package B.
5. Turn the secured unit to its upright position. Using the nuts and bolts with washers from Package A, attach the
handrail (D) onto the left side of the cart and the working platform (C) on the right side.
To Install Main Unit on Cart (sold separately)
1. Set the main unit (A) on the top side of the storage cabinet (J).
2. Hook the pot (B) onto the main unit’s hanger. If done correctly, its roller bar should be on the door side of the
machine.
3. Take the power plug from the main unit’s (A) ceiling and connect it with the socket on the bottom of the pot (B).
4. Inside the storage cabinet (J), release the two spring shafts underneath the main unit (A). Secure the main unit to
the storage base.
**For operating, cleaning and maintenance instructions, please see the popper manual.
Cleaning and Maintenance
To avoid burning of excess amount of sugar stays onto bottom of the inner pot, it is strongly
recommended to clean the popping pot after using 3 to 4 times.
After using the popcorn machine, users should use wet towel to clean up the main unit, main
body and glasses; rubbish tray is strongly recommended to tidy up frequently so that there is no
bacteria.
Quick Cleaning Procedure:
Switch OFF (II & III). Pour 300 to 500 ml of water (NO detergent is necessary) into inner pot.
Switch ON the stirrer (II) & heater (III) again to boil the water and let the stirrer to turn in order to
remove excess amount of sugar stuck on the surface. Pour out the water after about 1 to 2
minutes of boiling. Caution: Hot kettle!
Repeat the same procedure 2 to 3 times to get better result.
Standard cleaning procedure:
1. Repeat the above “Quick cleaning procedure” until it’s relatively cleans.
2. Switch off the machine and wait for the popping pot becomes cold. Clean the inside and
outside of the pot by brush and wet towel. (NEVER immerse the pot into water.)
-5 -
POPCORN MACHINE
Model no. & Specifications:
Model no.: NP08001-NP08004 & NP08001SE
Voltage ：AC 120V~60Hz
Input Power：860W
Please read this user manual carefully before assembling and using.
Assembling Manual
A. Main unit x 1 pc B. Popping pot x 1 pc
C. Working platform x 1 pc D. Hand rail x 1 pc
E. Square pole x 2 pcs F. Long stand x 1 set
G. Short stand x 1 set H. Wheel axis x 1 pc.
J. Wheels x 2 pcs. K. Storage cabinet x 1 pc
L. Popcorn scoop x 1 pc M. Kernel scoop + Oil scoop set
N. Parts x 1 box include:
-(Package A) gold plated bolts x 8 pcs. + nuts x 8 pcs. + washers x 8 pcs.
-(Package B) bolts x 8 pcs. + washers x 4 pcs.,
-(Package C) nuts with round cap x 2 pcs. + washers x 2 pcs.
-(Package D) wrench x 2 pcs.
-2 -
Fig. 1
Fig.2
Fig. 3
Fig. 4
IHG
A B CD E F
J