Caroma Urbane II 300071W User manual

Installation and Operating Instructions
300070W Livewell Electronic Bidet Seat
Installation and Operating Instructions
300071W Urbane II Electronic Bidet Seat

Safety Precautions
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW PROTECTION CONFORMING
TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3.
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2 AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT HAS AN INTEGRAL AIR-GAP HIGH HAZARD THAT COMPLIES WITH AS2845.2:2010.
THIS TOILET DOUCHE SEAT COMPLIES WITH THE BACK SIPHONAGE TEST TO AS2845.2:1996.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH A DUAL CHECK VALVE THAT COMPLIES WITH AS2845.1 AS PER
AS/NZS 3500.1 REQUIREMENTS.
NOTE: LOCAL AUTHORITIES HAVE VARYING REQUIREMENTS IN REGARD TO BACKFLOW PREVENTION. IF UNSURE WE
RECOMMEND THE USE OF AN ADDITIONAL RPZ VALVE (NOT INCLUDED).
Caroma will not be liable for any loss arising from failure to comply with the following:
1. is product is an “I” type electrical appliance and must be safely connected to the grounding system.
2. is product is an electrical appliance and should not be installed in a location where it can come in
contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply cord gets damaged, do not use until it has been repaired by a qualied electrician.
4. e appliance should be permanently connected to the water supply.
5. e Portable Residual Current Device (PRCD) is supplied as part of the power supply cord and must
be reliably xed.
To avoid the risk of electric shock, short circuit or re,
NEVER perform the following:
1. Do not insert or remove power plug with wet hands.
2. e power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the exible water inlet hose.
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
2
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
• e supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
• Do not use recycle water.
Safety Precautions
2
SAFETY PRECAUTIONS
WARNING: THIS TOILET DOUCHE MUST BE INSTALLED WITH APPROPRIATE BACKFLOW
PROTECTION CONFORMING TO THE NATIONAL CONSTRUCTION CODE - VOLUME 3
INSTALLATION MUST BE IN ACCORDANCE WITH AS/NZS 3500. 2
AND PLUMBING CODE OF AUSTRALIA.
THIS TOILET DOUCHE SEAT IS SUPPLIED WITH DUAL CHECK VALVES AND IT ALSO
HAS AN AIR GAP IN THE WATER TANK THAT IS COMPLIANT TO AS2845. 2 - WATER
SUPPLY BACKFLOW PREVENTION.
NOTE: LOCAL AUTHORITIES MAY HAVE VARYING REQUIREMENTS. CHECK TO
CONFIRM IF A RPZ VAULVE IS REQUIRED.
Caroma will not be liable for any loss arising from failure to comply with the following:
1. This product is an “I”type electrical appliance and must be safely connected to the
grounding system.
2. This product is an electrical appliance and should not be installed in a location where it can
come in contact with splashing water e.g. close to a shower or a high temperature location.
3. If the power supply code becomes damaged, do not use until it has been repaired by a qualified
electrician.
4. The appliance should be permanently connected to the water supply.
5. The Portable Residual Current Device (PRCD) is supplied as part of the power supply cord
and must be reliably fixed.
2
Caroma Industries Limited.
ABN 35 000 189 499
1 Melito Court, Prestons, NSW 2170
National Call Centre 13 14 16
caroma.com.au
To avoid the risk of electric shock, short circuit or fire,
never perform the following:
1. Do not insert or remove power plug with wet hands.
2. The power supply must comply with local regulations.
3. Do not turn the product upside down.
4. Do not distort or bend the flexible water inlet hose.
Safety Precautions
WARNING
• Battery is hazardous and is to be kept away from children
(whether the battery is new or used)
• Battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected
the battery has been swallowed or placed any part of the body.
WARNING
• The supplied remote control has been tested and complies with
the requirements of AS/NZS 62368.1: 2018. consumer goods
(products containing button/coin batteries) safety standard 2020.
Caution - the bidet and remote control operate with batteries. It has a possibility to interfere with pacemakers, debrillators or other
medical devices which is used for assistance. For safety reasons, it is advised that a certain safe distance is to be kept at all times between
the bidet and the medical device.
Date of Issue: 20/03/2023
Rev no.4

Bill of Material
Installation and Operating Instructions
300070W Livewell Electronic Bidet Seat
Installation and Operating Instructions
300071W Urbane II Electronic Bidet Seat
Bidet Seat
Part Number 300071W
Installation and Operating Instructions
300070W Livewell Electronic Bidet Seat
Installation and Operating Instructions
300071W Urbane II Electronic Bidet Seat
Urbane II Bidet Seat Remote Control
Part Number 300078
T Valve Stop Valve
Bidet Seat Filter
Part Number 300077 Dual Check Valve
3
Bill of Material
3
Installation and Operating Instructions
300070W Livewell Electronic Bidet Seat
Livewell Bidet Seat
Remote Control
Part Number: 300075
Bidet seat
Remote control
(batteries not
included; requires
2 x Type 3V CR2032)
Bidet Seat Filter
Part Number: 300077
Remote control
holder
Ball Valve Installation Template
Dual Check Valve Flexible Water Inlet Hose
Toggle Clamps Seat Fixing Screws
and Washers
Seat Fixing Plate
Livewell Bidet Seat Hinge Fixing Kit
Part Number: 300076
Flexible Water Inlet Hose
Pan Fixing
Bill of Material
3
Installation and Operating Instructions
300070W Livewell Electronic Bidet Seat
Livewell Bidet Seat
Remote Control
Part Number: 300075
Bidet seat
Remote control
(batteries not
included; requires
2 x Type 3V CR2032)
Bidet Seat Filter
Part Number: 300077
Remote control
holder
Ball Valve Installation Template
Dual Check Valve Flexible Water Inlet Hose
Toggle Clamps Seat Fixing Screws
and Washers
Seat Fixing Plate
Livewell Bidet Seat Hinge Fixing Kit
Part Number: 300076
End Cap

Technical Specication
M
M
O
O
D
D
E
E
L
L
300071W
300071W
W
W
a
a
s
s
h
h
R
R
e
e
a
a
r Wash
r Wash
ƽ
ƽ
F
F
e
e
m
m
a
a
l
l
e
e
W
W
a
a
s
s
h
h
ƽ
ƽ
M
M
a
a
s
s
s
s
a
a
g
g
e
e
ƽ
ƽ
A
A
d
d
j
j
u
u
s
s
t
t
a
a
b
b
l
l
e
e
W
W
a
a
t
t
e
e
r
r
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
5 Steps (Default 3rd)
5 Steps (Default 3rd)
A
A
d
d
j
j
u
u
s
s
t
t
a
a
b
b
l
l
e Flow Rate
e Flow Rate
5 Steps (Default 3rd)
5 Steps (Default 3rd)
A
A
d
d
j
j
u
u
s
s
t
t
a
a
b
b
l
l
e
e
S
S
p
p
r
r
a
a
y
y
P
P
o
o
s
s
i
i
t
t
i
i
o
o
n
n
5 Steps (Default 5th)
5 Steps (Default 5th)
W
W
a
a
r
r
m Air
m Air
A
A
i
i
r Drying
r Drying
ƽ
ƽ
A
A
d
d
j
j
u
u
s
s
t
t
a
a
b
b
l
l
e Air Rate
e Air Rate
5 Steps (Default 3rd)
5 Steps (Default 3rd)
A
A
d
d
j
j
u
u
s
s
t
t
a
a
b
b
l
l
e
e
Dryer
Dryer
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
5 Steps (Default 3rd)
5 Steps (Default 3rd)
H
H
e
e
a
a
t
t
e
e
d Seat
d Seat
H
H
e
e
a
a
t
t
e
e
d Seat
d Seat
-
-
A
A
d
d
j
j
u
u
s
s
t
t
a
a
b
b
l
l
e Seat Temperature
e Seat Temperature
H
H
y
y
g
g
i
i
e
e
n
n
e
e
D
D
e
e
o
o
d
d
o
o
r
r
i
i
s
s
e
e
r
r
ƽ
ƽ
N
N
o
o
z
z
z
z
l
l
e
e
A
A
u
u
t
t
o
o
m
m
a
a
t
t
i
i
c
c
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
ƽ
ƽ
N
N
o
o
z
z
z
z
l
l
e
e
M
M
a
a
n
n
u
u
a
a
l
l
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
ƽ
ƽ
D
D
e
e
s
s
c
c
a
a
l
l
i
i
n
n
g
g
ƽ
ƽ
D
D
i
i
s
s
p
p
l
l
a
a
y
y
S
S
c
c
r
r
e
e
e
e
n
n
ƽ
ƽ
R
R
e
e
m
m
o
o
t
t
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
ƽ
ƽ
N
N
i
i
g
g
h
h
t
t
L
L
i
i
g
g
h
h
t
t
ƽ
ƽ
O
O
p
p
e
e
n
n
C
C
o
o
v
v
e
e
r
r
/
/
S
S
e
e
a
a
t
t
A
A
u
u
t
t
o
o
m
m
a
a
t
t
i
i
c
c
a
a
l
l
l
l
y
y
W
W
a
a
t
t
e
e
r Supply Connector
r Supply Connector
G
G
⅜
⅜
on unit with G
on unit with G
½
½
flex hose
flex hose
R
R
a
a
t
t
e
e
d Voltage
d Voltage
A
A
C
C
2
2
2
2
0 -
0 -
2
2
4
4
0
0
V,
V,
5
5
0
0
/
/
6
6
0
0
H
H
Z
Z
P
P
o
o
w
w
e
e
r
r
1
1
1
1
7
7
0
0
W
W
L
L
e
e
n
n
g
g
t
t
h of Powder Cord
h of Powder Cord
1
1
.
.
8
8
m
m
W
W
a
a
t
t
e
e
r Supply Pressure
r Supply Pressure
70
70


750kp
750kp
a
a
(
(
0
0
.
.
7
7


7
7
.
.
5
5
B
B
a
a
r
r
)
)
W
W
a
a
t
t
e
e
r Supply Temperature
r Supply Temperature
4
4


3
3
5
5
ć
ć
A
A
m
m
b
b
i
i
e
e
n
n
t
t
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
4
4


4
4
0
0
ć
ć
P
P
r
r
o
o
t
t
e
e
c
c
t
t
i
i
o
o
n
n
D
D
e
e
g
g
r
r
e
e
e
e
I
I
P
P
X
X
4
4
W
W
a
a
s
s
h
h
D
D
e
e
v
v
i
i
c
c
e
e
F
F
l
l
o
o
w
w
R
R
a
a
t
t
e
e
3
3
5
5
0
0


6
6
5
5
0
0
m
m
L
L
/
/
m
m
i
i
n
n
W
W
a
a
t
t
e
e
r
r
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
3
3
1
1


3
3
9
9
ć
ć
W
W
a
a
s
s
h
h
C
C
y
y
c
c
l
l
e
e
T
T
i
i
m
m
e
e
3
3
M
M
i
i
n
n
u
u
t
t
e
e
s
s
H
H
e
e
a
a
t
t
i
i
n
n
g
g
M
M
o
o
d
d
e
e
T
T
a
a
n
n
k
k
H
H
e
e
a
a
t
t
e
e
r
r
P
P
o
o
w
w
e
e
r
r
1
1
2
2
0
0
0
0
W
W
S
S
a
a
f
f
e
e
t
t
y
y
D
D
e
e
v
v
i
i
c
c
e
e
T
T
h
h
e
e
r
r
m
m
a
a
l Cuto Fuses\Liquid
l Cuto Fuses\Liquid
B
B
a
a
c
c
k
k
fl
fl
o
o
w
w
P
P
r
r
e
e
v
v
e
e
n
n
t
t
i
i
o
o
n
n
A
A
i
i
r Gap of AB Type
r Gap of AB Type
D
D
r
r
y
y
D
D
e
e
v
v
i
i
c
c
e
e
S
S
p
p
e
e
e
e
d
d
O
O
f
f
A
A
i
i
r
r
ı
ı
4
4
m
m
/
/
S
S
D
D
r
r
y
y
e
e
r
r
P
P
o
o
w
w
e
e
r
r
3
3
5
5
0
0
W
W
D
D
r
r
y
y
C
C
y
y
c
c
l
l
e
e
T
T
i
i
m
m
e
e
3
3
M
M
i
i
n
n
u
u
t
t
e
e
s
s
W
W
a
a
r
r
m
m
A
A
i
i
r
r
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
3
3
5
5


5
5
0
0
ć
ć
S
S
a
a
f
f
e
e
t
t
y
y
D
D
e
e
v
v
i
i
c
c
e
e
T
T
h
h
e
e
r
r
m
m
a
a
l Cuto Fuses\Thermostat
l Cuto Fuses\Thermostat
D
D
e
e
o
o
d
d
o
o
r
r
i
i
z
z
a
a
t
t
i
i
o
o
n
n
D
D
e
e
o
o
d
d
o
o
r
r
i
i
z
z
a
a
t
t
i
i
o
o
n
n
M
M
o
o
d
d
e
e
D
D
i
i
a
a
t
t
o
o
m
m
D
D
e
e
o
o
d
d
o
o
r
r
i
i
z
z
a
a
t
t
i
i
o
o
n
n
C
C
y
y
c
c
l
l
e
e
T
T
i
i
m
m
e
e
1
1
5
5
M
M
i
i
n
n
u
u
t
t
e
e
s
s
H
H
e
e
a
a
t
t
e
e
d Seat
d Seat
H
H
e
e
a
a
t
t
e
e
d
d
P
P
o
o
w
w
e
e
r
r
5
5
0
0
W
W
S
S
e
e
a
a
t
t
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
2
2
9
9


3
3
7
7
ć
ć
S
S
a
a
f
f
e
e
t
t
y
y
D
D
e
e
v
v
i
i
c
c
e
e
T
T
h
h
e
e
r
r
m
m
a
a
l Cuto Fuses\Thermostat
l Cuto Fuses\Thermostat
R
R
e
e
m
m
o
o
t
t
e Control
e Control
F
F
r
r
e
e
q
q
u
u
e
e
n
n
c
c
y
y
R
R
a
a
n
n
g
g
e
e
2
2
4
4
0
0
0
0
-2520
-2520
M
M
H
H
z
z
M
M
a
a
x
x
i
i
m
m
u
u
m
m
R
R
F
F
O
O
u
u
t
t
p
p
u
u
t
t
P
P
o
o
w
w
e
e
r
r
-
-
1
1
0
0
d
d
B
B
m
m
T
T
y
y
p
p
e of Batteries
e of Batteries
3
3
V
V
C
C
R
R
2
2
0
0
3
3
2
2
(Not supplied)
(Not supplied)
N
N
u
u
m
m
b
b
e
e
r of batteries
r of batteries
T
T
w
w
o
o
P
P
i
i
e
e
c
c
e
e
s
s
O
O
t
t
h
h
e
e
r Safety Device
r Safety Device
R
R
e
e
s
s
i
i
d
d
u
u
a
a
l
l
C
C
u
u
r
r
r
r
e
e
n
n
t
t
D
D
e
e
v
v
i
i
c
c
e
e
s
s
ƽ
ƽ
Drying /
Drying /
ƽ
ƽ
5 Steps (Default 3rd)
5 Steps (Default 3rd)
4

Bidet Dimensions
5
533
188 502
370
353
213
276
540
29
Unit : mm

Installation Steps
• Before installation, Make sure the inlet hose is installed and the area is equipped
to supply power
ese operations should be performed by qualied service personnel
6
1 2
3 4 Plug
Screw
‘O’- Rings
readed
Insert
75
Pan Centreline
Conduit Location
for Power Cord
1/2” BSP
Nipple
Water and Power Locations.
Refer to Pan Installation Instructions for details
140
85
30
90
105
Unit : mm
270
Finished
wall
1/2” B.S.P.
nipple
15
Mark centre line
of pan on wall
and oor
85
130
1/2” BSP
nipple
Ø30mm hole location
for power cord
275
Important:
Pan foot level
Flex Hose To
Bidet Seat
Follow above for wall faced close coupled pan with back entry cistern
connection and wall faced back inlet pan.
For bottom inlet Cistern connection, remove end cap on Tee tting and
install G1/2” to G1/2” exible hose, 450mm recommended (not supplied)
Unit : mm
1/2” Inch Stop
End Cap
Isolation
Valve
Tee Fitting
Dual Check
Valve
Filter
90O Elbow
1/2” B.S.P.
end cap
Tee tting
Dual check
valve
Washer
Stop valve
Power connector
for bidet seat
Filter
Flex hose to
bidet seat
G1/2” to G1/2”
bent elbow hose
450mm
Flex hose to
bidet seat

Reset
7
Installation Steps
5 6
7 8
Align male end
of power cable
connector with
female end,
push it in and
turn the nut all
the way,
as shown above
Turn the water mains ON, check for leakage. Turn the
power on and press the reset button as shown above.
Aer making sure power cable and circuit breaker are
placed inside the pan, push the seat while aligning the
seat xing plugs with xing holes in seat. Pull the excess
length of power cable from the other end if required. For Cistern installation, follow instructions supplied
with it.
Fit the elbow end of hose to the inlet connection of the
seat and hand tighten the nut. Ensure the elbow is pointing
to the le or forward.
Note: If the
installation is not
in place, user
could lubricate
the O-RING on
the xed column
with appropriate
water.

Install the Remote Control
10
A1 A2
A3 A4
This side up
Recommended in stallation area
Recommended Installation Area
8
Install the Remote Control
Recommended Installation Area
PP


1 2
3 4

9
Overview

















Night Detector LED Status
Stop/Dry Rear Wash Female Wash Program Entry

10
Remote Control
Rear Wash
Dryer / Stop
Cover Open / Close
Female Wash
Massage
Open / Close
Increase Flow and
Air Volume
Increase Position
Increase Water and
Air Temperature
1. e remote control requires 2 batteries (3V CR2032). (Not supplied)
2. e remote control provided is only to be used for model 300071W Urbane II Electronic
Bidet Seat.
300071W Urbane II
Electronic Bidet Seat
Remote Control
Decrease Flow and
Air Volume
Decrease Position
Decrease Water and
Air Temperature

11
Function Introduction
Initialization
Aer connection to the power and water supply, please wait for about 2 minutes for the Bidet to initialize.
Do not operate during this period. User needs to be seated for the bidet functions to operate
Wash Operation
Press the “Wash” button on the remote control to start the wash. It will automatically stop aer 3
minutes, you can also stop washing by pressing the “Stop” button.
Note: While on Rear wash or Female wash mode, it will wash at the xed position for about 10 seconds,
and on movable wash mode it will wash for about 18 seconds, then it returns to the normal position.
OR - You can operate by pressing side seat buttons
for wash operations
Rear Wash Female Wash
55HHDDUUZZDDVVKK))HHPPDDOOHHZZDDVVKK
''UU\\22SSHHUUDDWWLLRRQQ






●



●


 
 

NOTICE



Rear Wash
Female Wash
Drying Operation
Please be seated
To begin drying, press the “Dry / Stop” button to
start drying (LED status: RED). It will automatically
stop aer 3 minutes or you can press the “Dry / Stop”
button to stop (LED status: ORANGE).
Massage Operation
In the process of Rear or Female washing
Repeatly press the "Massage" button on the remote
until you choose your desired spray mode
Oscillating : one indicator light is on
Pulsating : two indicator lights are on
Oscillating + Pulsating : three indicator lights are on
Remote control LEDS

12
Function Introduction
Stop Operation
In the process of Rear washing , Female washing or drying
Press the "Stop" button on the remote control
it will stop washing or drying.....OR
Press the “Dry / Stop” side button on seat to
stop washing or drying.
Adjusting Water Flow Rate
In the process of rear washing or female washing,
press the “ow adjustment” button on the remote
control to adjust the ow rate.
Adjusting the Nozzle Position
In the process of rear washing or female washing,
press “position adjustment” buttons on the remote
control to adjust the nozzle position forward or backward.
During Drying, press the “Increase” or “Decrease”
button to “Adjust temperature” on remote control to
adjust the Air Temperature.
Digital display function: when air temperature is adjusted,
the screen will display the air temperature accordingly.
During Female/Rear Washing, press the “Increase”
or “Decrease” button of “Adjust temperature” on
remote control to adjust the Water Temperature.
Digital display function: when the water temperature is
adjusted, the screen will display the water temperature accordingly.
Adjust Water Temperature
Adjust Drying Air Temperature
Adjusting Drying Air Flow
During Drying, to select drying option, press “ow
adjustment” buttons on the remote control to adjust
the blower air ow rate.

1. Adjusting Seat Temperature
Press and hold “+” or “–” and press “Seat
Open/Close” for temperature button and
press seat button to adjust the seat temperature.
ere are 6 modes (including turning o seat heating mode),
every time the seat button is pressed, the mode will change.
Digital display function: When seat
temperature is adjusted, the screen will
display the seat temperature accordingly.
2. Anti Scald Setting
Aer 10 minutes of use or more of the bidet seat, you will notice that the temperature
continues to be at its lowest level of 29ºC.
To change temperature of the seat, activate the heating functions on the remote control
13
Function Introduction
Adjusting Temperature
Auto Lid Opening / Closing
f
f
150±50
150±50
Far
Far
mode
mode
Near
Near
mode
mode
Short range
dectection
Long range
dectection
Cover open
or close
Seat open
or close
Cover / Seat Open or Close
Press the “Cover open/close” button on the remote control
to open or close the cover, press the “Seat open/close”
button to open or close the seat.
Press and hold “+” or “–” and press “Lid open /
close” on the remote control to adjust the dierent
modes for the automatic open / close function
+
Long range dectection mode is set as
default. Led lights on the remote control
indicate the following status
Digital Display
Function
OFF
Short range detection
Long range detection
Remote control
LEDS
Range Mode
+
5 seat settings
290C 1 led
310C 2 led
330C 3 led
350C 4 led
370C 5 led
o 0 led

14
Function Introduction
Cover / Seat Open or Close
Automatic mode
e function of automatic lid open/close, the lid will open automatically when the user detection
sensor detects movement within the sensor range. e lid will close automatically aer about 60
seconds when the user detection sensor does not detect any movement within the sensor range.
Please remember
l. When the user walks within the sensing area slowly, the sensing distance for lid opening/closing
may be shortened. If the lid does not respond, please open or close the lid with the remote
control or by hands.
2. e function of automatic lid open/close works only when the “Setting of lid open/close”
on the remote controller is set to “On”.
3. When any movement is detected in the toilet (such as opening and closing doors or uttering
curtains), the lid may open automatically. (If it continues to open by mistake due to the
bathroom environment, the automatic seat open/close mode can be turned o
on the remote control). When used by children, the user detection sensor may fail to detect due
to height detection.
4. It is recommended not to open or close the cover/seat forcefully. Any extreme force to open or
close the cover and seat manually could cause damage to the auto open and close modes and
this can cause a product function failure.
Manual mode
Users can open or close the lid and seat directly by hands. When user intends to open or close
the lid and seat under normal condition, the lid/seat will open or close automatically against
the trend of motion. e user should not use force. Once being stopped by any obstacle during
motion, the lid or seat will stop moving automatically.
Note: During automatic open/close of lid and seat, do not use extreme force to open or close the lid or seat.
Night Light Setting
Smart mode for the night light is set as default. Press and
hold "Increase" or "Decrease" button of "Adjust temperature"
+ repeatedly press "Decrease" button of "Adjust Position"
on the remote control to change modes.
NOTE: When it’s in “smart” mode, the night light switches on in a dark environment and switches o in a bright environment.
Remote control LEDS Mode
Close Mode
Always on Mode
Smart Mode
O mode: when one indicator light is on
Always on: when two indicator lights are on
Smart mode: when three indicator lights are on
14
Function Introduction
Cover / Seat Open or Close
Automatic mode
e function of automatic lid open/close, the lid will open automatically when the user detection
sensor detects movement within the sensor range. e lid will close automatically aer about 60
seconds when the user detection sensor does not detect any movement within the sensor range.
Please remember
l. When the user walks within the sensing area slowly, the sensing distance for lid opening/closing
may be shortened. If the lid does not respond, please open or close the lid with the remote
control or by hands.
2. e function of automatic lid open/close works only when the “Setting of lid open/close”
on the remote controller is set to “On”.
3. When any movement is detected in the toilet (such as opening and closing doors or uttering
curtains), the lid may open automatically. (If it continues to open by mistake due to the
bathroom environment, the automatic seat open/close mode can be turned o
on the remote control). When used by children, the user detection sensor may fail to detect due
to height detection.
4. It is recommended not to open or close the cover/seat forcefully. Any extreme force to open or
close the cover and seat manually could cause damage to the auto open and close modes and
this can cause a product function failure.
Manual mode
Users can open or close the lid and seat directly by hands. When user intends to open or close
the lid and seat under normal condition, the lid/seat will open or close automatically against
the trend of motion. e user should not use force. Once being stopped by any obstacle during
motion, the lid or seat will stop moving automatically.
Note: During automatic open/close of lid and seat, do not use extreme force to open or close the lid or seat.
Night Light Setting
Smart mode for the night light is set as default. Press and
hold "Increase" or "Decrease" button of "Adjust temperature"
+ repeatedly press "Decrease" button of "Adjust Position"
on the remote control to change modes.
NOTE: When it’s in “smart” mode, the night light switches on in a dark environment and switches o in a bright environment.
Remote control LEDS Mode
Close Mode
Always on Mode
Smart Mode
O mode: when one indicator light is on
Always on: when two indicator lights are on
Smart mode: when three indicator lights are on
//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+


15
Function Introduction
Deodorise Setting
Display Function
When a person is close or during uses, the display will illuminate. It shows seat temperature by
default. When seated, the display screen shows the seat temperature. When it starts washing, the
display screen shows current water temperature. When it starts drying, the display screen shows
current air temperature. 5 seconds aer washing or drying stops, the display screen will again show
the seat temperature.
Changing temperature display units
e display window shows degrees Celsius by default.
Press and hold "Increase" or "Decrease" button for
"Adjust temperature" + press "Massage" on remote control
to change the display from degrees Celsius to degrees Fahrenheit.
Fault warning: e display screen will show the Fault code as per
“Fault warnings and codes V0.2”. e display screen light will not
change but the status LED will ash in red and with sound warning.
It will return to normal when the fault is solved.
''LLVVSSOODD\\IIXXQQFFWWLLRRQQ
When person is close or it’s during use, the display will open. It shows water temperature by
default.
When it’s seated, the display screen shows the seat temperature. (If the model is without seat
heating function, it shows current water temperature).
shows current water temperature.
temperature.
temperature).
and Fahrenheit degree.
+

Change temperature unit
Smart mode for the deodorization by default. It is on when the user sits down and it will be o
aer one minute when the user leaves. If there is no operation of washing or drying during being
seated, this mode will cancel aer 15 minutes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase"
or "Adjust Position" on the remote control to turn the
deodorisation function on and o.
O mode :when one indicator light is on
On mode :when two indicator lights are on
//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

++
Remote control LEDS Mode
Close Mode
Smart Mode
''LLVVSSOODD\\IIXXQQFFWWLLRRQQ
When person is close or it’s during use, the display will open. It shows water temperature by
default.
When it’s seated, the display screen shows the seat temperature. (If the model is without seat
heating function, it shows current water temperature).
shows current water temperature.
temperature.
temperature).
and Fahrenheit degree.
+

Change temperature unit
LED Status
When seated (LED status: Orange), press “Rear wash” or “
Female wash” side buttons to start the washing (LED status: Red).
It will automatically stop aer 3 minutes or you can press
“Stop/ Dry” side button to stop washing (LED status: Orange).
When no one is seated and not in operation, the LED status is Green.
(
(








V
V
L
L
G
G
H
H


E
E
X
X
W
W
W
W
R
R
Q
Q
V
V


R
R
S
S
H
H
U
U
D
D
W
W
L
L
R
R
Q
Q
When it’s seated (status LED: orange), press “Rear wash” or
“Female wash” side buttons to start the washing (status LED: red).
It will automatically stop after 3 minutes or you can press “Stop/
Dry” side button to stop washing (status LED: orange).
When it’s unseated and no any operation, the status LED is green.

LED status
Stop Rear Female
Wash Wash
Power Standby Setting
When not seated, continue pressing the side buttons for more
than 6 seconds, it will go into power standby mode. Press again
on the side buttons for more than 6 seconds to restart
the functions.


16
Function Introduction
Sound Setting
e sound is on by default. ere will be a BEEP
when the bidet has received commands or signals.
Press and hold “lncrease” or “Decrease” button to
“Adjust temperature” + press “Front Wash” Remote control LEDS Mode
O Mode
On Mode
Intelligent power saving mode and
timed power saving mode.
Intelligent power saving mode: e product
will detect when not in use, seat temperature
will stay at the lowest level.
Timed power saving mode: Set unused time
range (6 or 9 hours), seat will not be heated.
is mode will automatically exit aer
6 or 9 hours.
Intelligent + Timed power saving mode:
If the two modes are set at the same time,
the smart power saving mode could work
even if not in the timed power saving period.
Press and hold “Increase” or “Decrease”
button to “Adjust temperature” + repeatedly
press “Increase” button of “Adjust Flow”
to change mode.
Range Mode
OFF
O
Time: 6H
Time: 9H
Intelligent
Intelligent +
Time: 6H
Intelligent +
Time: 9H
Digital
Display
Function
Remote Control
LEDS
Power Saving Mode
+
14
Function Introduction
Cover / Seat Open or Close
Automatic mode
e function of automatic lid open/close, the lid will open automatically when the user detection
sensor detects movement within the sensor range. e lid will close automatically aer about 60
seconds when the user detection sensor does not detect any movement within the sensor range.
Please remember
l. When the user walks within the sensing area slowly, the sensing distance for lid opening/closing
may be shortened. If the lid does not respond, please open or close the lid with the remote
control or by hands.
2. e function of automatic lid open/close works only when the “Setting of lid open/close”
on the remote controller is set to “On”.
3. When any movement is detected in the toilet (such as opening and closing doors or uttering
curtains), the lid may open automatically. (If it continues to open by mistake due to the
bathroom environment, the automatic seat open/close mode can be turned o
on the remote control). When used by children, the user detection sensor may fail to detect due
to height detection.
4. It is recommended not to open or close the cover/seat forcefully. Any extreme force to open or
close the cover and seat manually could cause damage to the auto open and close modes and
this can cause a product function failure.
Manual mode
Users can open or close the lid and seat directly by hands. When user intends to open or close
the lid and seat under normal condition, the lid/seat will open or close automatically against
the trend of motion. e user should not use force. Once being stopped by any obstacle during
motion, the lid or seat will stop moving automatically.
Note: During automatic open/close of lid and seat, do not use extreme force to open or close the lid or seat.
Night Light Setting
Smart mode for the night light is set as default. Press and
hold "Increase" or "Decrease" button of "Adjust temperature"
+ repeatedly press "Decrease" button of "Adjust Position"
on the remote control to change modes.
NOTE: When it’s in “smart” mode, the night light switches on in a dark environment and switches o in a bright environment.
Remote control LEDS Mode
Close Mode
Always on Mode
Smart Mode
O mode: when one indicator light is on
Always on: when two indicator lights are on
Smart mode: when three indicator lights are on
//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

14
Function Introduction
Cover / Seat Open or Close
Automatic mode
e function of automatic lid open/close, the lid will open automatically when the user detection
sensor detects movement within the sensor range. e lid will close automatically aer about 60
seconds when the user detection sensor does not detect any movement within the sensor range.
Please remember
l. When the user walks within the sensing area slowly, the sensing distance for lid opening/closing
may be shortened. If the lid does not respond, please open or close the lid with the remote
control or by hands.
2. e function of automatic lid open/close works only when the “Setting of lid open/close”
on the remote controller is set to “On”.
3. When any movement is detected in the toilet (such as opening and closing doors or uttering
curtains), the lid may open automatically. (If it continues to open by mistake due to the
bathroom environment, the automatic seat open/close mode can be turned o
on the remote control). When used by children, the user detection sensor may fail to detect due
to height detection.
4. It is recommended not to open or close the cover/seat forcefully. Any extreme force to open or
close the cover and seat manually could cause damage to the auto open and close modes and
this can cause a product function failure.
Manual mode
Users can open or close the lid and seat directly by hands. When user intends to open or close
the lid and seat under normal condition, the lid/seat will open or close automatically against
the trend of motion. e user should not use force. Once being stopped by any obstacle during
motion, the lid or seat will stop moving automatically.
Note: During automatic open/close of lid and seat, do not use extreme force to open or close the lid or seat.
Night Light Setting
Smart mode for the night light is set as default. Press and
hold "Increase" or "Decrease" button of "Adjust temperature"
+ repeatedly press "Decrease" button of "Adjust Position"
on the remote control to change modes.
NOTE: When it’s in “smart” mode, the night light switches on in a dark environment and switches o in a bright environment.
Remote control LEDS Mode
Close Mode
Always on Mode
Smart Mode
O mode: when one indicator light is on
Always on: when two indicator lights are on
Smart mode: when three indicator lights are on
//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+

//LLJJKKWW66HHWWWWLLQQJJ
''HHRRGGRRUULL]]HH66HHWWWWLLQQJJ
Close mode : when one indicator light is on
Always on mode : when two indicator lights are on
Smart mode : when three indicator lights are on
N
NOOTTEE:: TThhee ""ssmmaarrtt"" mmooddee rreeffeerrss tthhaatt tthhee nniigghhtt lliigghhtt wwiillll lliigghhtt uupp iinn aa ddaarrkk eennvviirroonnmmeenntt aanndd
lliigghhtt ooffff iinn aa bbrriigghhtt eennvviirroonnmmeenntt..
●
●Smart mode for the deodorization by default. It is on when the user sits down and it will be off
after one minute when the user leaves.
If there is no operation of washing or drying during being seated, it will be off after 15 minutes.
Close mode : when one indicator light is on
Smart mode : when two indicator lights are on
Smart mode for the night light by default. Press and hold
"Increase" or "Decrease" button of "Adjust temperature" +
repeatedly press "Decrease" button of "Adjust Position" on
the remote control to change modes.
Press and hold "Increase" or "Decrease" button of
"Adjust temperature" + repeatedly press "Increase" of
"Adjust Position" on the remote control to open or
close deodorization.
+
+


N
e
w l
t
e
r
17
a new one

a new one

a new one

Nozzle Cleaning
e nozzle will be automatically cleaned before washing and aer washing.
e operation of manual cleaning is as follows
Open the cover and seat, press the "Stop" and
"Female Wash" side buttons at the same time,
or press and hold the “Stop” + press “Decrease” on the
remote control, the nozzle will come out with water
and the nozzle head can be removed and cleaned manually.
e nozzle will retract automatically aer 5 minutes,
or you can press the "Stop" button and the nozzle will
retract itself to the normal position.
Replacing the lter
a new one

a new one

a new one

1 2 3
4 5
e seat will need to be lied to access the lter. e lter has a service life of 6 months.
is is depended on the water quality. e lter should be replaced when the water ow is restricted.
1 2 3 4

18
Care and Maintenance
Maintenance interval Maintenance activity
Weekly Clean all surfaces and corners. Clean the spray nozzle if required. See
“Nozzle cleaning”
Every half year Replace the lter if required.
Every year Descal the device. See “Descaling the device”
Cleaning agents and tools
• Cleaning agents and tools
Do not use the cleaning agents of strong acid and alkali
To clean the E-bidet, do not use the hard brush e.g. toilet brush / nylon brush
Self-cleaning the tank
If not used for more than 72 hours, when the user operates the washing, it will open the
self-cleaning for about 3 minutes. All the buttons are invalid during the self- cleaning and it
will return to normal aer the self-cleaning.
&&DDUUHHDDQQGGFFOOHHDDQQLLQQJJ
&&OOHHDDQQLLQQJJDDJJHHQQWWVVDDQQGGWWRRRROOVV
00DDLLQQWWDDLLQQLLQQJJLLQQWWHHUUYYDDOO00DDLLQQWWDDLLQQLLQQJJDDFFWWLLYYLLWW\\
'DLO\ 5HPRYHZDWHUGURSVZLWKDVRIWOLQWIUHHFORWKWRDYRLG
OLPHVFDOHVWDLQV
:HHNO\ &OHDQDOOVXUIDFHVDQGFRUQHUV&OHDQWKHVSUD\QR]]OHLI
UHTXLUHG6HH1R]]OHFOHDQLQJ
0RQWKO\ &OHDQWKH:&FHUDPLFDSSOLDQFHZLWKDORZDFLGLFFOHDQLQJ
DJHQWV
(YHU\KDOI\HDU 5HSODFHWKHILOWHULIUHTXLUHG
(YHU\\HDU 'HVFDOWKHGHYLFH6HH'HVFDOLQJWKHGHYLFH
CClleeaanniinngg aaggeennttss aanndd ttoooollss
●
))2255%%,,''
DDoo nnoott uussee tthhee cclleeaanniinngg aaggeennttss ooff ssttrroonngg aacciidd aanndd aallkkaallii
TToo cclleeaann tthhee EE--bbiiddeett ,, ddoo nnoott uussee tthhee hhaarrdd bbrruusshh ..ee..gg.. ttooiilleett bbrruusshh nnyylloonn bbrruusshh
TToo cclleeaann tthhee WWCC cceerraammiicc aapppplliiaannccee ,,ddoo nnoott uussee tthhee mmaattaall bbrruusshh
DDaammaaggee ttoo tthhee ddeevviiccee ffrroomm aaggggrreessssiivvee ddeessccaalliinngg aaggeennttss
66HHOOIIFFOOHHDDQQLLQQJJWWKKHHWWDDQQNN
112277,,&&((
Not used for more than 72 hours, when the user operates the washing ,it will open
the self-cleaning for about 3 minutes. All the buttons are invalid during the self-
cleaning and it will return to normal after the self-cleaning.

FFoorr WWCC cceerraammiicc aapppplliiaannccee
soft cloths ,lint-free cloths
low acidic cleaning agents .e.g.
heavily diluted citric acid.
toilet brush.
FFoorr EE--bbiiddeett
soft cloths ,lint-free cloths
mild cleaning agents that are
kind to the skin.
&&DDUUHHDDQQGGFFOOHHDDQQLLQQJJ
&&OOHHDDQQLLQQJJDDJJHHQQWWVVDDQQGGWWRRRROOVV
00DDLLQQWWDDLLQQLLQQJJLLQQWWHHUUYYDDOO00DDLLQQWWDDLLQQLLQQJJDDFFWWLLYYLLWW\\
'DLO\ 5HPRYHZDWHUGURSVZLWKDVRIWOLQWIUHHFORWKWRDYRLG
OLPHVFDOHVWDLQV
:HHNO\ &OHDQDOOVXUIDFHVDQGFRUQHUV&OHDQWKHVSUD\QR]]OHLI
UHTXLUHG6HH1R]]OHFOHDQLQJ
0RQWKO\ &OHDQWKH:&FHUDPLFDSSOLDQFHZLWKDORZDFLGLFFOHDQLQJ
DJHQWV
(YHU\KDOI\HDU 5HSODFHWKHILOWHULIUHTXLUHG
(YHU\\HDU 'HVFDOWKHGHYLFH6HH'HVFDOLQJWKHGHYLFH
CClleeaanniinngg aaggeennttss aanndd ttoooollss
●
))2255%%,,''
DDoo nnoott uussee tthhee cclleeaanniinngg aaggeennttss ooff ssttrroonngg aacciidd aanndd aallkkaallii
TToo cclleeaann tthhee EE--bbiiddeett ,, ddoo nnoott uussee tthhee hhaarrdd bbrruusshh ..ee..gg.. ttooiilleett bbrruusshh nnyylloonn bbrruusshh
TToo cclleeaann tthhee WWCC cceerraammiicc aapppplliiaannccee ,,ddoo nnoott uussee tthhee mmaattaall bbrruusshh
DDaammaaggee ttoo tthhee ddeevviiccee ffrroomm aaggggrreessssiivvee ddeessccaalliinngg aaggeennttss
66HHOOIIFFOOHHDDQQLLQQJJWWKKHHWWDDQQNN
112277,,&&((
Not used for more than 72 hours, when the user operates the washing ,it will open
the self-cleaning for about 3 minutes. All the buttons are invalid during the self-
cleaning and it will return to normal after the self-cleaning.

FFoorr WWCC cceerraammiicc aapppplliiaannccee
soft cloths ,lint-free cloths
low acidic cleaning agents .e.g.
heavily diluted citric acid.
toilet brush.
FFoorr EE--bbiiddeett
soft cloths ,lint-free cloths
mild cleaning agents that are
kind to the skin.
For E-bidet
So cloths,
lint-free cloths
Mild cleaning
agents that are kind
to the skin.

19
Descaling the Device
• e shower toilet needs to be descaled at least once a year or more oen,
depending on the amount of use and the water quality.
• Duing the descaling function, the shower toilet can be used except for the washing
functions.
• e descaling process will take 30 minutes. During this time, the LED will ash in red
and when descaling is nished, the LED will change to green.
• Please use descaling agents with low foam.
Only use mild descaling additives
Open the cover Open the descaling
cover
Open the rubber
cover .
Pour descaling
agents .
Dosage:
about 150mL
NOTICE:
ere is water
ow from the
nozzle at this
stage.
Close the rubber
cover and descaling
cover .
Close the seat and
cover.
en the descaling
procedure will start.
''HHVVFFDDOOLLQQJJWWKKHHGGHHYYLLFFHH
●The shower toilet needs to be descaled at least once in a year or more often,
depending on the using frequency and the water quality.
●
●The descaling lasts 30 minutes. During this time, the status LED keep flashing in red and
when descaling is finished, the status LED changes to green.
DDaammaaggee ttoo hhuummaann bbooddyy aanndd tthhee ddeevviiccee ffrroomm aaggggrreessssiivvee ddeessccaalliinngg
aaggeennttss ..
●Please use descaling agents with less foam.
Duingthe descaling, the shower toilet can be used except for the washing functions.


''HHVVFFDDOOLLQQJJWWKKHHGGHHYYLLFFHH
●The shower toilet needs to be descaled at least once in a year or more often,
depending on the using frequency and the water quality.
●
●The descaling lasts 30 minutes. During this time, the status LED keep flashing in red and
when descaling is finished, the status LED changes to green.
DDaammaaggee ttoo hhuummaann bbooddyy aanndd tthhee ddeevviiccee ffrroomm aaggggrreessssiivvee ddeessccaalliinngg
aaggeennttss ..
●Please use descaling agents with less foam.
Duingthe descaling, the shower toilet can be used except for the washing functions.


''HHVVFFDDOOLLQQJJWWKKHHGGHHYYLLFFHH
●The shower toilet needs to be descaled at least once in a year or more often,
depending on the using frequency and the water quality.
●
●The descaling lasts 30 minutes. During this time, the status LED keep flashing in red and
when descaling is finished, the status LED changes to green.
DDaammaaggee ttoo hhuummaann bbooddyy aanndd tthhee ddeevviiccee ffrroomm aaggggrreessssiivvee ddeessccaalliinngg
aaggeennttss ..
●Please use descaling agents with less foam.
Duingthe descaling, the shower toilet can be used except for the washing functions.


''HHVVFFDDOOLLQQJJWWKKHHGGHHYYLLFFHH
●The shower toilet needs to be descaled at least once in a year or more often,
depending on the using frequency and the water quality.
●
●The descaling lasts 30 minutes. During this time, the status LED keep flashing in red and
when descaling is finished, the status LED changes to green.
DDaammaaggee ttoo hhuummaann bbooddyy aanndd tthhee ddeevviiccee ffrroomm aaggggrreessssiivvee ddeessccaalliinngg
aaggeennttss ..
●Please use descaling agents with less foam.
Duingthe descaling, the shower toilet can be used except for the washing functions.


'
'
H
H
V
V
F
F
D
D
O
O
L
L
Q
Q
J
J


W
W
K
K
H
H


G
G
H
H
Y
Y
L
L
F
F
H
H


●The shower toilet needs to be descaled at least once in a year or more often,
depending on the using frequency and the water quality.
●
●The descaling lasts 30 minutes. During this time, the status LED keep flashing in red and
when descaling is finished, the status LED changes to green.
D
D
a
a
m
m
a
a
g
g
e
e
t
t
o
o
h
h
u
u
m
m
a
a
n
n
b
b
o
o
d
d
y
y
a
a
n
n
d
d
t
t
h
h
e
e
d
d
e
e
v
v
i
i
c
c
e
e
f
f
r
r
o
o
m
m
a
a
g
g
g
g
r
r
e
e
s
s
s
s
i
i
v
v
e
e
d
d
e
e
s
s
c
c
a
a
l
l
i
i
n
n
g
g
a
a
g
g
e
e
n
n
t
t
s
s
.
.
●Please use descaling agents with less foam.
Duingthe descaling, the shower toilet can be used except for the washing functions.


1 2 3
4 5 6

20
Draining the Water Tank
Drain the water tank
5
Close the rubber cover and descaling cover .
6
Close the cover and seat. Then it will start
the descaling procedure. During the
descaling, the shower toilet can be used
except for the washing functions. The
descaling lasts 30 minutes. During this
time, the status LED keep flashing in red
and when descaling is finished, the status
LED changes to green.
1. The water and power must be cut before you disassemble the E-Bidet
2. Do not invert or tilt it before you finish draining the water tank
1.Hold the plug with the tipper , turn to
"open" , and pull out . It will start to drain .
2. After completing the drainage , insert
the plug and turn to "CLOSE" .
18
O
P
E
N
C
L
O
S
E
C
M
Y
CM
MY
CY
CMY
K
1. e water and power must be turned o before you disassemble the E-Bidet
2. Do not invert or tilt it before you nish draining the water tank
1. Use long nose plies- to hold, rotate and pull out the drain plug. It will start to drain.
2. Aer completing the drain process, insert the plug back and rotate to “CLOSE” .
One-ON-One Setting
To install several shower toilets in the same area,
if you want each remote control to control the
specied shower toilet, please set as following steps.
1. In the status of unseated, press and hold
"Decrease" button of "Adjust temperature"
+ press and hold "Stop/Dry" button on the remote
control until all 5 LED lights are on,
then release the pressing.
2. Press “Increase” or “Decrease” of “Adjust Flow”
to choose dierent code for each shower
toilet, and press “Stop/Dry” side button,
then press “Stop/Dry” on the remote control.
When long “beep” sound heard, the setting
is nished.
2
2
Q
Q
H
H
ü
ü
2
2
1
1
ü
ü
2
2
Q
Q
H
H
6
6
H
H
W
W
W
W
L
L
Q
Q
J
J
+
+
+
+
set as following steps.
1.
the pressing.
2.

+
Drain the water tank
5
Close the rubber cover and descaling cover .
6
Close the cover and seat. Then it will start
the descaling procedure. During the
descaling, the shower toilet can be used
except for the washing functions. The
descaling lasts 30 minutes. During this
time, the status LED keep flashing in red
and when descaling is finished, the status
LED changes to green.
1. The water and power must be cut before you disassemble the E-Bidet
2. Do not invert or tilt it before you finish draining the water tank
1.Hold the plug with the tipper , turn to
"open" , and pull out . It will start to drain .
2. After completing the drainage , insert
the plug and turn to "CLOSE" .
18
O
P
E
N
C
L
O
S
E
C
M
Y
CM
MY
CY
CMY
K
Drain the water tank
5
Close the rubber cover and descaling cover .
6
Close the cover and seat. Then it will start
the descaling procedure. During the
descaling, the shower toilet can be used
except for the washing functions. The
descaling lasts 30 minutes. During this
time, the status LED keep flashing in red
and when descaling is finished, the status
LED changes to green.
1. The water and power must be cut before you disassemble the E-Bidet
2. Do not invert or tilt it before you finish draining the water tank
1.Hold the plug with the tipper , turn to
"open" , and pull out . It will start to drain .
2. After completing the drainage , insert
the plug and turn to "CLOSE" .
18
O
P
E
N
C
L
O
S
E
C
M
Y
CM
MY
CY
CMY
K