Carrier WIRELESS STANDARD SENSOR User manual

W
Wi ir re el le es ss s S Se en ns so or rs s
I
In ns st ta al ll la at ti io on n G Gu ui id de e
CARRIER CORPORATION ©2018
A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-584-01 · 5/23/2018

Verify that you have the most current version of this document from
www.hvacpartners.com
or your local Carrier
office.
Important changes are listed in
Document revision history
at the end of this document.
CARRIER CORPORATION ©2018. All rights reserved throughout the world. i-Vu is a registered trademark of Carrier
Corporation. All other trademarks are the property of their respective owners.

Contents
Overview of wireless sensors...................................................................................................................................... 1
Standard sensor....................................................................................................................................................4
Specifications ........................................................................................................................................ 4
Plus sensor ............................................................................................................................................................6
Specifications ........................................................................................................................................ 6
Pro-F sensor...........................................................................................................................................................8
Specifications ........................................................................................................................................ 8
Motion/Lux sensor............................................................................................................................................. 10
Specifications ......................................................................................................................................11
Window/Door sensor ........................................................................................................................................ 12
Specifications ......................................................................................................................................13
Wireless Adapter................................................................................................................................................ 14
Specifications ......................................................................................................................................15
USB Radio ........................................................................................................................................................... 16
Specifications ......................................................................................................................................16
Planning the layout of wireless devices...................................................................................................................17
Rnet configuration............................................................................................................................................. 17
Wireless device placement guidelines........................................................................................................... 18
Pairing sensors to the Wireless Adapter using SensorBuilder ..............................................................................22
Step 1: Download and install SensorBuilder................................................................................................ 22
Step 2: Pair sensors to the Rnet Wireless Adapter..................................................................................... 23
To install the USB Radio driver ........................................................................................................................ 25
Using SensorScan to determine the best location for devices ..............................................................................26
Step 1: Download and install SensorScan..................................................................................................... 26
Step 2: Verify signal strengths......................................................................................................................... 27
Using SensorScan and SensorBuilder to test control program logic.....................................................................29
Installing the Wireless Adapter and sensors...........................................................................................................30
To install the Wireless Adapter........................................................................................................................ 30
To install a Standard or Plus sensor ............................................................................................................... 32
To install a Pro-F sensor.................................................................................................................................... 34
To install a Motion/Lux sensor ........................................................................................................................ 35
To install a Window/Door sensor.................................................................................................................... 36
Troubleshooting the wireless sensor installation ......................................................................................... 39
Adjusting Wireless Adapter and wireless sensor settings......................................................................................40
To edit the Wireless Adapter's settings.......................................................................................................... 40
To edit a sensor's settings................................................................................................................................ 41
To update the Wireless Adapter firmware...............................................................................................................43
Compliance ................................................................................................................................................................44
FCC Compliance................................................................................................................................................. 44
CE Compliance ................................................................................................................................................... 44
Industry Canada Compliance........................................................................................................................... 45
Appendix A: SensorBuilder overview.......................................................................................................................46
Driver and Devices panes................................................................................................................................. 47
Device configuration pane ............................................................................................................................... 48
Sensors pane...................................................................................................................................................... 50
Reusing configurations in SensorBuilder....................................................................................................... 51

Contents
Appendix B: SensorScan overview ..........................................................................................................................52
Sensor right-click menu .................................................................................................................................... 53
Received Test-Answer Messages window...................................................................................................... 54
Message details window................................................................................................................................... 55
Send window ...................................................................................................................................................... 56
Message filter window ...................................................................................................................................... 57
Automated reporting window .......................................................................................................................... 58
Document revision history ........................................................................................................................................60

Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
1
Carrier wireless sensors, designed for zone control, are low-power devices that use light-harvesting through solar
panels as their primary power source. The wireless line of sensors includes the models shown in the table below.
The wireless sensors communicate with a Wireless Adapter that is wired to the Rnet port of a controller. The
Wireless Adapter translates the sensor's customized EnOcean protocol into the Rnet protocol so that the sensors
can be integrated with the existing programming logic for wired ZS sensors.
NOTE
Wireless sensors do not operate with the standard EnOcean protocol, and third-party wireless sensors do
not operate on the Rnet network.
The wireless Standard and Plus sensors should typically be located no more than 75 to 80 ft. (22.86 ot 24.38 m)
from the Wireless Adapter. The Pro-F, Motion/Lux, and Window/Door sensors should typically be located no more
than 60 ft. (18.29 m) from the Wireless Adapter. These measurements are based on the Wireless Adapter and
sensor being separated by no more than 1 drop ceiling and 2 walls (drywall with metal studs). Longer distances
can be achieved if there are fewer obstructions. See Planning the layout of wireless devices (page 17) for more
information on placement and building material impact.
REQUIREMENTS
•A v6.5 or later i-Vu® system
•v6-00 or later controller drivers
Wireless sensor
models
Features
Available Configurations
Part number
Standard • No user control Temperature only - 902 MHz - Logo
Temp - 868 MHz - Logo
Temp - 902 MHz - No logo
Temp/humidity - Logo
Temp/humidity - No logo
Temp through field-supplied
remote thermistor - Logo
Temp through field-supplied
remote thermistor - No logo
WS2-T-C-902
WS2-T-C-868
WS2-T-902
WS2-TH-C-902
WS2-TH-902
WS2-R-C-902
WS2-R-902
Plus • Setpoint
adjustment
Temp only - 902 MHz - Logo
Temp - 868 MHz - Logo
Temp - 902 MHz - No logo
Temp/humidity - 902 MHz - Logo
Temp/humidity - 902 MHz - No logo
WS2-TO-C-902
WS2-TO-C-868
WS2-TO-902
WS2-THO-C-902
WS2-THO-902
Overview of wireless sensors

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
2
Wireless sensor
models
Features
Available Configurations
Part number
Pro-F •
•
•
•
Temperature,
humidity, and
motion sensor
Setpoint
adjustment
Fan control
Digital display (non-
programmable)
902 MHz - Logo
868 MHZ - Logo
902 MHz - No logo
WS-THMDOF-C-902
WS-THMDOF-C-868
WS-THMDOF-902
Motion/Lux Sensor •
•
•
Motion sensor
Lux sensor
LED status
indicator
902 MHz
868 MHz
WS-ML-902
WS-ML-868
Window/Door Sensor •
•
Magnetic relay switch
LED status
indicator
902 MHz
868 MHz
WS-S-902
WS-S-868

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
3
Wireless Adapter
Features
Available Configurations
Part number
•
•
•
•
•
USB update port
LED status
indicator
Reset button
Rnet connector
24 Vac power
connector
902 MHz
868 MHz
RG-902
RG-868
USB Radio
902 MHz
868 MHz
WS-US-902
WS-US-868

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
4
Standard sensor
•Sensing options:
○Temperature only
○Temperature and relative humidity
○Connector for field-supplied remote
thermistor *
•Wireless
•Solar-powered—Indoor solar panel collects
ambient light to power the sensor and send
wireless communication
•Maintenance-free capacitors power the
transmitter during unlit periods for up to 5 days
without a light source
•Supplemental battery included for extreme low-
light conditions
*10K Type 2 remote thermistor such as Carrier's non-communicating button sensor, wall plate sensor, and
outside air temperature sensor. Examples of remote thermistor use include outside air, return/supply air duct,
walk-in cooler, or placing thermistor in one location and the sensor in a different location that provides better
signal/light strength.
See To install a Standard or Plus sensor (page 32).
Specifications
Sensor temperature range 32°F to 104°F (0° to 40°C)
NOTE
If temperature exceeds 104°F (40°C), sensor will continue to report
104°F (40°C) until temperature drops below this limit.
Humidity sensor 11% to 89%, ±3% RH typical
Power supply Solar harvesting, internal energy storage
Battery A 1/2 AA 3.6V 1200 mA battery is included to supplement solar power in
extreme low-light conditions. For battery replacement, you can purchase this
3.6V battery online from websites such as Amazon.
Battery shelf life expectancy: 10 years
Battery operational life expectancy: 5 to 10 years
NOTE
Although a common 1/2 AA 3V battery will fit into the sensor’s battery
socket, the battery life will be substantially shorter, and the battery life
calculations in your i-Vu® system will never exceed 40%.
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
5
Transmission range Typically, 75 to 80 ft. (22.86 to 24.38 m) maximum from the Wireless
Adapter, assuming sensor and Wireless Adapter are separated by no more
than 1 drop ceiling or 2 walls (drywall with metal studs)
Transmission interval Configurable in SensorBuilder. The sensor transmits:
•On change of sensed value, and
•At a regular interval (heartbeat). The default is every 900 seconds (15
minutes). Set the heartbeat to 0 to transmit only when value changes.
Change of value threshold Configurable in SensorBuilder. The temperature must change by at least
.288°F (.156°C) (the default) for the sensor to send a change of value.
Maximum operating life with no
light power or battery
Up to 5 days
Minimum lighting strength
required for operation
150 lux, constant
Minimum lighting strength
required to minimize battery
usage
700 lux, constant
Time to fully charge Depends on available lux. Sensor will fully charge in 8 hours @ 1000 lux, or 24
hours @ 333 lux.
Degree of protection IP20
Operating environment 32°F to 122°F (0° to 50°C)
5% to 95% relative humidity (non-condensing)
Housing ABS plastic, bright white color
Weight 0.2 lb. (0.08 kg)
Dimensions 3.55 in. W x 3.77 in. H x 0.84 in. D
(9.03 cm W x 9.57 cm H x 2.13 cm D)
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: 2ANUH-LSTM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe:
Mark
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
6
Plus sensor
•Sensing options:
○Temperature only
○Temperature and relative humidity
•Wireless
•Setpoint dial to adjust the room temperature
setpoint *
•Solar-powered—Indoor solar panel collects
ambient light to power the sensor and send
wireless communication
•Maintenance-free capacitors power the
transmitter in unlit periods for up to 5 days
without a light source
•Supplemental battery included for extreme low-
light conditions
*A change made to the room temperature setpoint through the dial may take up to a minute to be seen in i-Vu®.
See To install a Standard or Plus sensor (page 32).
Specifications
Sensor temperature range 32°F to 104°F (0° to 40°C)
NOTE
If temperature exceeds 104°F (40°C), sensor will continue to report
104°F (40°C) until temperature drops below this limit.
Humidity sensor 11% to 89%, ±3% RH typical
Power supply Solar harvesting, internal energy storage
Battery A 1/2 AA 3.6V 1200 mA battery is included to supplement solar power in
extreme low-light conditions. For battery replacement, you can purchase this
3.6V battery online from websites such as Amazon.
Battery shelf life expectancy: 10 years
Battery operational life expectancy: 5 to 10 years
NOTE
Although a common 1/2 AA 3V battery will fit into the sensor’s battery
socket, the battery life will be substantially shorter, and the battery life
calculations in your i-Vu® system will never exceed 40%.
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)
Transmission range Typically, 75 to 80 ft. (22.86 to 24.38 m) maximum from the Wireless
Adapter, assuming sensor and Wireless Adapter are separated by no more
than 1 drop ceiling or 2 walls (drywall with metal studs)

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
7
Transmission interval Configurable in SensorBuilder. The sensor transmits:
•On change of sensed value, and
•At a regular interval (heartbeat). The default is every 900 seconds (15
minutes). Set the heartbeat to 0 to transmit only when value changes.
Change of value threshold Configurable in SensorBuilder. The temperature must change by at least
.288°F (.156°C) (the default) for the sensor to send a change of value.
Maximum operating life with no
light power or battery
Up to 5 days
Minimum lighting strength
required for operation
150 lux, constant
Minimum lighting strength
required to minimize battery
usage
700 lux, constant
Time to fully charge Depends on available lux. Sensor will fully charge in 8 hours @ 1000 lux, or 24
hours @ 333 lux.
Degree of protection IP20
Operating environment 32°F to 122°F (0° to 50°C)
5% to 95% relative humidity (non-condensing)
Housing ABS plastic, bright white color
Weight 0.2 lb. (0.08 kg)
Dimensions 3.55 in. W x 3.77 in. H x 0.84 in. D
(9.03 cm W x 9.57 cm H x 2.13 cm D)
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: 2ANUH-LSTM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe:
Mark
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
8
Pro-F sensor
See To install a Pro-F sensor (page 34).
•Temperature and relative humidity
sensor
•On-board PIR (passive infrared) motion
sensor
•Digital non-programmable display shows
temperature, setpoint adjustment value,
and icons to indicate the following:
Occupied (motion
detected)
Unoccupied
Low battery
Transmitting
Sensor is not receiving a
response from the
Wireless Adapter
NOTE
Humidity reading can be
seen only in the i-Vu® interface.
•Wireless
•Solar-powered—Indoor solar panel
collects ambient light to power the
sensor and send wireless
communication
•Buttons to:
○Switch display between
Fahrenheit and Celsius
○Turn on the fan
○Raise or lower the room
temperature setpoint.
Maximum adjustment is
defined in the control program.
Specifications
Sensor temperature range 32°F to 104°F (0° to 40°C)
NOTE
If temperature exceeds 104°F (40°C), sensor will continue to report
104°F (40°C) until temperature drops below this limit.
Humidity sensor 0% to 100%, ±3% RH typical. 0.5% drift per year.
Motion sensor Panasonic AMN42122

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
9
Motion effective detection range 16.4 ft. (5 m) maximum
Motion detection speed Standard motion detection is 0.8 to 1.2 m/sec.
Slight motion detection is 0.5 m/sec.
Motion temperature detection Detectable change in temperature between the target and background is
more than 7.2°F (4°C)
Power supply Solar harvesting, internal energy storage
Batteries Two SAFT LS-14500 AA 3.6V batteries. Not user replaceable.
Battery shelf life expectancy: 10 years
Battery operational life expectancy: 5 years
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)
Transmission range Typically, 60 ft. (18.29 m) maximum from the Wireless Adapter, assuming
sensor and Wireless Adapter are separated by no more than 1 drop ceiling or
2 walls (drywall with metal studs)
Transmission interval Configurable in SensorBuilder. The sensor transmits:
•On change of sensed value, and
•At a regular interval (heartbeat). The default is every 900 seconds (15
minutes). Set the heartbeat to 0 to transmit only when value changes.
Change of value threshold Configurable in SensorBuilder. The temperature must change by at least
.288°F (.156°C) (the default) for the sensor to send a change of value.
Humidity change of value threshold is 3% (not configurable).
Maximum operating life with no
light power
Up to 4 days
Minimum lighting strength
required for operation
150 lux, constant
Minimum lighting strength
required to minimize battery
usage
700 lux, constant
Time to fully charge Depends on available lux. Sensor will fully charge in 8 hours @ 1000 lux, or 24
hours @ 333 lux.
Degree of protection IP30
Operating environment 32°F to 122°F (0° to 50°C)
5% to 95% relative humidity (non-condensing)
Housing ABS plastic, traffic white color
Weight .48 lb. (.22 kg)
Dimensions 3.7 in. W x 6.24 in. H x .79 in. D
9.4 cm W x 15.85 cm H x 2 cm D

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
10
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: SZV-STM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe:
Mark
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3
Motion/Lux sensor
•Passive infrared motion sensor
•Wireless
•Solar-powered—Indoor solar panels
collect ambient light to power the sensor
and send wireless communication
•Supplemental battery included for
extreme low-light conditions
See To install a Motion/Lux sensor (page 35).

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
11
Specifications
Motion effective detection range 39 ft (12 m) maximum
Motion effective detection angle
(horizontal & vertical)
102° x 92°
Light sensor measuring range 0 to 1020 lux
Power supply Solar harvesting, internal energy storage
Supplemental battery A 1/2 AA 3.6V 1200 mA battery is included to supplement solar power in
extreme low-light conditions. For battery replacement, you can purchase this
3.6V battery online from websites such as Amazon.
Battery shelf life expectancy: 10 years
Battery operational life expectancy: 5 to 10 years
NOTE
Although a common 1/2 AA 3V battery will fit into the sensor’s battery
socket, the battery life will be substantially shorter, and the battery life
calculations in your i-Vu® system will never exceed 40%.
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)
Transmission range Typically, 60 ft. (18.29 m) maximum from the Wireless Adapter, assuming
sensor and Wireless Adapter are separated by no more than 1 drop ceiling or
2 walls (drywall with metal studs)
Transmission interval Configurable in SensorBuilder. The sensor transmits:
•On change of sensed value, and
•At a regular interval (heartbeat). The default is every 900 seconds (15
minutes). Set the heartbeat to 0 to transmit only when value changes.
Change of value threshold The value must change by at least 40 lux for the sensor to send a change of
value.
Maximum operating life with no
light power or battery
Up to 4 days
Minimum lighting strength
required for operation
40 lux, constant
Minimum lighting strength
required to minimize battery
usage
700 lux, constant
Time to fully charge Depends on available lux. Sensor will fully charge in 8 hours @ 1000 lux, or 24
hours @ 333 lux.
Degree of protection IP50
Operating environment -3° to 140°F (20° to 60°C)
5% to 95% relative humidity (non-condensing)
Housing ABS plastic, traffic white color
Weight 0.2 lb. (.09 kg)
Dimensions 3.17 in. W x 4.02 in. H x 1.25 in. D
(8.05 cm W x 10.2 cm H x 3.18 cm D)

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
12
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: SZV-STM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe:
Mark
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3
Window/Door sensor
•Sensor detects when a door or window
opens or closes
•Wireless
•Solar-powered—Indoor solar panel
collects ambient light to power the
sensor and send wireless
communication
•Supplemental battery included for
extreme low-light conditions
•Installs on standard door and window
frames
See To install a Window/Door sensor (page 36).

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
13
Specifications
Power supply Solar harvesting, internal energy storage
Battery A CR1216 battery is included to supplement solar power in extreme low-light
conditions.
Battery shelf life expectancy: 10 years
Battery operational life expectancy: 5 to 10 years
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)
Transmission range Typically, 60 ft. (18.29 m) maximum from the Wireless Adapter, assuming
sensor and Wireless Adapter are separated by no more than 1 drop ceiling or
2 walls (drywall with metal studs)
Transmission interval The sensor transmits:
•On change of sensed value, and
•At a regular 25-minute interval (heartbeat).
Maximum operating life with no
light power or battery
Up to 4 days
Minimum lighting strength
required for operation
15 lux, constant
Minimum lighting strength
required to minimize battery
usage
700 lux, constant
Maximum sensor gap 0.25 in. (6.4 mm)
Degree of protection IP50
Operating environment Indoor rated only
32° to 131°F (0° to 55°C)
5% to 95% relative humidity (non-condensing)
Housing ABS plastic, ceiling white color
Weight 0.97 oz. (27.5 g)
Dimensions Sensor:
Magnet:
3.15"L x 0.83"W x 0.59"D
(8.0 cm x 2.1 cm x 1.5 cm)
3.15"L x 0.47"W x 0.5"D
(8.0 cm x 1.2 cm x 1.3 cm)

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
14
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: SZV-STM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe:
Mark
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3
Wireless Adapter
•Translates the sensors' customized
EnOcean protocol into the Rnet protocol
•Wired to a controller's Rnet port
•Powered by an 24 Vac external power
supply
•USB port for firmware upgrade
See To install the Wireless Adapter (page 30).

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
15
Specifications
Power requirements 24 Vac or 24 Vdc ±10% @ 125 mA
Power supply 24 Vac or 24 Vdc external power supply, Class 2
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)
Transmission range Typically, 60 ft. (18.29 m) maximum from Wireless Adapter, assuming sensor
and Wireless Adapter are separated by no more than 1 drop ceiling or 2 walls
(drywall with metal studs).
Protection Communication Port is optically isolated.
Operating environment Indoor rated only
0° to 130°F (-17.8° to 54.4°C)
10% to 90% relative humidity (non-condensing)
Housing UL94-5VA plenum rated enclosure, rugged GE C2950 Cycoloy plastic,
black color
Weight 4.3 oz. (121.9 g)
Dimensions 4.66 in. x 3.36 in. 1.39 in.
(11.84 cm x 8.53 cm x 3.53 cm)
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: SZV-STM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
cUL Listed UL 916,PAZX&, Energy Management Equipment
Europe:
Mark
EN50491-5-2:2009; Part 5-2: EMC requirements for HBES/BACS used in
residential, commercial and light industry environment
EN50491-3:2009, Part 3: Electrical safety requirements for Home and
Building Electronic Systems (HBES) and Building Automation and Control
Systems (BACS)
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3

Overview of wireless sensors
Wireless Sensors CARRIER CORPORATION ©2018
Installation Guide All rights reserved
16
USB Radio
•Required for commissioning sensors
•Connects to a computer's USB port to
allow communication between
SensorScan or SensorBuilder and the
Wireless Adapter and wireless sensors
NOTE
The orange antenna should always be straight. A bend in the antenna could degrade the signal.
Specifications
Protocol Customized version of EnOcean
Radio frequency 902 MHz (North America) or
868 MHz (Europe and China)
Transmission range Typically, 60 ft. (18.29 m) maximum
USB contact durability 500 cycles
Operating environment Indoor rated only
32° to 122°F (0° to 50°C)
0% to 90% relative humidity (non-condensing)
Weight .4 oz. (12 g)
Dimensions 2.76 in. x .9 in. x .35 in.
(7 cm x 2.3 cm x .9 cm)
Compliance United States of America:
FCC CFR47, Chapter 1, Subchapter A, Part 15, Subpart B, Class B
Contains FCC ID: SZV-STM300U
Canada:
Industry Canada Compliant, ICES-003, Class B
Contains IC ID: 6713A-STM300U
Europe:
Mark
Low Voltage Directive: 2014/35/EU
RoHS Compliant: 2011/65/EU
Australia and New Zealand:
C-Tick Mark, AS/NZS 61000-6-3