Carson Phantom Projector Lift User manual

Please read this manual before installing and using the
projection screen. Retain this manual for future reference.
Phantom Projector Lift
Instruction manual for Phantom projector lift

Items listed here may change without prior notice.
The company reserves the right to all of the listed items.
1. Projector mount body (1pc)
2. Top base plate (1pc)
3. Ceiling installation plate (1 pcs)
4. 600*600mm ceiling cover plate (1pcs)
5. Projector mount U shape hanger part (1pcs)
6. 6*25 hexagon socket round flat head
screws (4pcs)
6*20 hexagon socket round flat head
screws (4pcs)
4*20 hexagon socket round flat head
screws (4pcs)
7. M8 screws (4pcs)
8. Motor Stroke adjusting Rod (1pcs)
9. Cross screwdriver (1pcs)
1 2
4 5
7 8
12 13
17 18
14 15 16
9 10 11
6
3
10. Hexagon socket scewdriver (1pcs)
11. Compression Springs (4pc)
12. M10*20 cross recessed large flat head
screws (4pcs)
13. Expansion belt (4pcs)
14. Hexagon nut (16 pcs)
15. flat mat (16pcs)
16. M3*10 cross recessed large flat head
screws (3pcs)
17. PA gaskets (4pcs)
18. M6*10 hexagon socket flat head screws
(4pcs)

Important Safety Tips
 WARNING: Incorrect installation and improper use may lead to mechanical
failure or personal injury.
Considerations for installing / using this product
1. Handle with care to avoid damage.
2. Do not expose the product to rainwater or any other form of moisture.
3. Keep away from heat sources, such as radiators and other items that may
emit heat
4. Check whether the voltage is consistent with the required voltage.
The company will not be liable for any damages or injuries caused by a faulty
installation or operation.

Installation
Use a 10mm diameter drill bit to drill
holes in marked positions on the ceiling,
then use the 8*80 in those holes
expansion bolts to install the base plate.
Slide the main body of the motorized
projector mount into the top base plate,
tighten and x it with M10*20 cross
recessed large at head screw.
The wall
8*80expansion bolt
Top base plate
Picture 1 Picture 2 Picture 3
projector mountbody
Top base plate
Picture 5
M10*20 cross recessed
large at head screws
Cross
screwdriver
Picture 4

Pick the correct screw according to your
projector model to install the projector
and U - shaped hanger together.
Press the ‘down’ button on the remote
to lower the projector mount. Install the
projector on the projector mount.
Tighten the screws. Projector
installation complete.

Follow the instruction below to install
ceiling installation plate.
hexagonal nut
Compression Springs
at mat
hexagonal nut
M8 screws
Ceiling installation plate
at mat
hexagonal nut
bottom plate

Follow the instruction below to install
ceiling cover plate.
600*600mm ceiling
cover plate
M3*10 cross recessed
large at head screws
Ceiling decorative
board frame
Adjust the connecting
bolts so that the cover
plate ts into the
ceiling better

The projection direction
The projection direction
The projection direction
Ceiling installation
plate
Ceiling installation
plate
600*600mm ceiling
cover plate
screw
Adjust the tilt Angle of the projector.
Mount the 600*600 ceiling cover plate,
along the guide rail direction of the
ceiling installation plate. Screw xing.

Use the motor stroke adjusting rod to
adjust ‘’up limit size’’ and ‘’down limit
size’’ whenever necessary.
For ‘up limit’ adjustment, turn Red
knob:
Anti-clockwise – to reduce‘up limit’
Clockwise – to add ‘up limit’
For ‘down limit’ adjustment, turn
White knob:
Anti-clockwise – to add ‘down limit’
Clockwise – to reduce ‘down limit’
White knob
Red knob
Up Limit
Motor Stroke
adjusting Rod
Down limit

[email protected]
carsonscreens.com.au