CARVIN Vintage 16 User manual

VINTAGE16 SPECS:
RMS Power: 16/5 watts
Output Imp: 8Ω
Input Imp: 100,000 ohms
Tone Controls: BASS: 80Hz
MID: 600-700Hz
TREBLE: 11k Hz
Sensitivity: 1mV for clipping
16mV for full output
Preamp Tubes: 3—12AX7’s (dual stage)
Power Tubes: 2—EL84’s
USA Model: 120VAC, 300VA
USA Fuse: 1A 250V slow blow, 5x 20mm
Export Model: 240VAC
Export Fuse: 1A 250V slow blow, 5x 20mm
Cabinet Size: 16W x 17.75H x 8.5”D, 31 lbs.
Cabinet: 7-ply poplar wood
Warranty: One Year
Options: CV16 cover
CARVIN ENGINEERING DATA OPERATING MANUAL
NOMAD & BEL AIR COMBO SPECS:
Speakers: One/Two Celestion G12 Vintage 30 12” spks
RMS Power: 33 watts Vintage 33, 50 watts all others
Output Imp: 4, 8 & 16Ω
Input Imp: 100,000 ohms
Tone Controls: BASS: 80Hz
Both Channels: MID: 600-700Hz
TREBLE: 11k Hz
Ch 1 Sensitivity: 1mV for clipping
Ch 2 Sensitivity: 16mV for full output
Channels: 2—switching
Voiced Line Out: 1.5 VAC @ 100 watts RMS
Preamp Tubes: 5—12AX7’s (dual stage)
Power Tubes: 4—EL84’s
USA Model: 120VAC, 300VA
USA Fuse: 3A 250V slow blow, 5x 20mm
Export Model: 230VAC, 300VA
Export Fuse: 1.5A 250V slow blow, 5x 20mm
112 Cabinet : 19.5W x 10.25D x 17.5”H, 44 lbs.
212 Cabinet : 26W x 10.25D x 17.75”H, 56 lbs.
Cabinet: 7-ply poplar wood
Warranty: One Year
Options: CV3212 cover, FS22 footswitch
76-10302C 0705 12340 World Trade Drive, San Diego, CA 92128
800.854.2235 carvin.com
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
212 Bel Air™
NOMAD, BEL AIR COMBO & VINTAGE16 GUITAR AMPS
Congratulations on your purchase of the VINTAGE TUBE SERIES all tube ampli-
fier. Carvin has been building tube guitar amplifiers since 1949. They have been
used by top professionals like; Joe Walsh, Chet Atkins, Jeff Beck, James Burton,
Jorma Kaukonen, and many other great musicians. You will discover that these
amplifiers represent a significant sound improvement over conventional tube ampli-
fiers. Spend time with your new amp and get to know it’s many sounds.
TECHNICAL DESIGN OF THE VINTAGE TUBE SERIES
The VINTAGE TUBE SERIES is 100% tube design—no IC’s, FET’s or transistors. The design
criteria was to build an all-tube guitar amp that sounded better than anything else on the market.
This meant that the VINTAGE TUBE SERIES was going to be totally new from the ground up
and that it was going to be an all tube design.
DYNAMIC EL84 POWER TUBES
Premium EL84 power tubes are selected for their excellent saturation and power soak char-
acteristics. Just like early VOX AC30 amps, EL84’s are used for their ideal transconduc-
tance delivering a tight bottom and soft drive with superior definition.
HIGH IMPEDANCE GUITAR INPUT
Carvin has long known about the effects of miss-loading a guitar pickup which can cause
high frequency loss. The VINTAGE TUBE SERIES guards against this loss with its ultra high
input impedance. Also, we considered the capacitance of the average shielded guitar cable
which can reduce the high frequency response of your guitar pickups. Unlike other ampli-
fiers, we purposely avoided adding capacitance anywhere in the preamp to control high fre-
quency oscillations. Instead, we controlled oscillations through careful component layout
and lead placement allowing its shimmering highs to be reproduced.
CLEAN AND SOAK CHANNELS
The equalization of the clean and soak channel is designed to offer clarity to your instru-
ment. Special mud-cutting circuits eliminate the unwanted sounds in the 500 to 700 Hz
range which normally take away the tone definition of your instrument. You will also take
notice of the clean channels rear PRESENCE control which adds acoustic voicing to your
instrument. This control boosts only the guitars very highest harmonics which are in the
10k Hz range instead of the normal 3K Hz of a bright switch.
TONE CONTROLS
The T-Bridge passive BASS, MID and TREBLE tone controls offer a wide range of tone set-
tings. Take full advantage by setting them where they sound best. Your sound may not be at
center (5 on the dial). Instead, the treble and bass may need to be at 10 while the mid con-
trol at 0 (or) the treble at 1 and the bass at 10 depending dual or single coil pickups. These
controls will not affect or color your sound when set at extreme settings, nor do they interact
with each other. The greater range of these controls comes from the high impedance 1 meg
sealed pots (most guitar amps use 250k pots). The frequency of the bass control is set at 80
Hz while the mid control is set at 650 Hz. The treble control is set at a very high 11k Hz giving
the VINTAGE TUBE SERIES it’s dynamic highs.
REVERB
The FS22 footswith for the long tailed REVERB system in the VINTAGE TUBE SERIES switches
only the reverb “send” leaving the tail of the reverb to decay naturally, the way it’s done in
the studio. A special pre filter eliminates the spring “boing” normally heard in other sys-
tems giving it a “lush” sound. The all tube reverb system offers vibrant clarity with full depth
reminiscent of the sixties tube amps. Guitar Player magazine rated this system as one of
the best they have heard. The Vintage 16™ does not have the footswitch option.
RECEIVING INSPECTION—read before getting started
INSPECT YOUR AMP FOR ANY DAMAGE which may have occurred during shipping. If any
damage is found, please notify the shipping company and CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit,
always use the original carton and packing material. This will provide the best possible protec-
tion during shipment. CARVIN and the shipping company are not liable for any damage caused
by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately.
Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual
for your records. Keep your portion of the card and return the portion with your name and
comments to us.
GETTING STARTED QUICKLY
If you are like most players, you probably want to plug in your new amp and get started play-
ing it right away. You can read the rest of the manual later to learn the finer points of operat-
ing your amp. In order to get started you will need your VINTAGE TUBE SERIES amp, a 120
or 230 AC grounded power outlet, your instrument and a standard guitar cord. With the amp
turned off, you may now plug it into the proper AC voltage.
Now turn all the volume and drive controls off and set tone controls at their mid center posi-
tion. If you have purchased the FS22 foot switch, plug it into the rear foot switch jack for switch-
ing the channels and reverb. Note: The channel SELECT switch must be selected for channel
1 for the FS22 to function (a hum will be heard if it’s in the wrong position).
Now, turn the power switch and allow a few minuts for the tubes to warm up then turn on
the standby switch. Gradually raise the volume controls and re-adjust the tone controls and
your ready to go. Please call if you feel your amp is malfunctioning. Occasionally tubes are
damaged in shipping.
Nomad 112™
Vintage16™
c
FEATURES
CELESTION
SPEAKERS!

FRONT PANEL
1. GUITAR INPUT
A standard 1/4” input jack feeds both channels through using the SELECT channel switch. Use a
professional quality guitar cord no longer than 25 feet. Typical cable capacitance should be under
50pf—the longer the cord, the greater the capacitance (you can measure this with a capacitance meter).
A long cable with high capacitance will reduce the overall treble response from your pickups.
2. CHANNEL SELECT
Set the channel SELECT switch to the desired channel. Channel 1 is designed for clean playing
while channel 2 is designed for overdrive/sustain. For the FS22 foot switch to function, set the chan-
nel 2 SELECT switch to the channel 1 position.
CLEAN CHANNEL 1
3. CLEAN VOLUME 1
Use channel 1 for clean playing. Thanks to special mud-cutting circuits that work between the fre-
quencies of 500 and 700 Hz, your guitar tones will be full and vibrant.
4. CLEAN—BASS, MID & TREBLE CONTROLS
You can start at 5 on the dial for each of the tone controls. However, these settings do not repre-
sent a normalize (flat) sound. You need to set them where they sound best! Most musicians like
to reduce the MID’S between 1 and 4 for deeper bass and crisper highs. If your sound is too bright
with single coil pickups, you may want to keep the rear PRESENCE control off.
LEAD CHANNEL 2
5. SOAK—6. LEAD VOLUME 2
To get the Vintage overdrive, keep the VOLUME 2 (VOLUME for Vintage 16™) down until you have
determined your final gain level—think of this control as a master volume. Turn the SOAK control
up until you get the amount of overdrive you’re looking for. The setting will vary for the same amount
of overdrive depending on the pickups used—single or dual coil and the setting of your guitar. The
Vintage 16™ low wattage allows you to turn up both controls to get different distortions.
7. LEAD—BASS, MID & TREBLE
To start off with, set the BASS, MID & TREBLE controls at their center (5) position. These controls
are to be set according to the type of pickups used (dual or single coil). It’s normal to decrease the
BASS at higher playing levels.
MASTER SECTION
8. MASTER REVERB
Set the REVERB control for the desired amount (this works in both channels).
9. POWER INDICATOR LIGHT
As the amp is turned on, the red pilot light will illuminate.
REAR PANEL
10. AC POWER & FUSE
The detachable AC POWER CORD supplied is designed to operate with one type of voltage (the
European 230V export model uses a CEE-7 plug cord set). Check the rear power cord label for the
proper voltage and fuse value. Make sure the cord is securely inserted into the back of the unit. Plug
the cord into a grounded “3 prong” power source. No attempt should ever be made to defeat or use
the amp without the ground connected.
The FUSE (some models have circuit breakers) is located within the AC power cord receptacle. To
check or replace the fuse, remove the power cord, place a screwdriver under the “FUSE” cap and
pull the fuse holder out. The fuse type is a 250V Slow Blow SB 5 x 20mm rated at 3A for 120V &
1.5A for 230V models. Do not use fast acting fuse, only a SLOW BLOW (SB) type fuse will work.
The Vintage 16™ uses 1A slow blow for both 120 VAC and 250 VAC models.
11. POWER SWITCH
The rear POWER SWITCH is to be utilized as the master ON/OFF switch. The front panel light will
illuminate when the amp is switched on. (The power switch is on the front of the Vintage 16™.)
12. STANDBY SWITCH
Use the rear STANDBY SWITCH If you are taking a break. This turns the high voltage off, increas-
ing the life of your power tubes while keeping the power and preamp tube filaments on for imme-
diate use.
13. ACOUSTIC PRESENCE
The rear ACOUSTIC PRESENCE control adds a sibilance to the high frequencies of your guitar. Most
presence controls work in the 3k to 4k range. However, the VINTAGE TUBE’s presence starts at a
very high 8k Hz delivering 10 dB at 12k Hz and continues to 20k Hz which extends all the upper har-
monics of your guitar. The amount of sibilance will depend on the speakers used. To keep both
channels totally independent, the ACOUSTIC PRESENCE is switched by relay only into clean chan-
nel 1. The effect of the ACOUSTIC PRESENCE will seem ever so slight, however, the result is added
sibilance only to the ultra-high frequencies.
VINTAGE TUBE SERIES FRONT & REAR PANEL CONTROLS
FUSE
2
5 31 6
4
BEL AIR & NOMAD
10 11 12 13
14
Press firmly until cord clicks in.

14. EFFECTS LOOP
For the lowest possible noise from an effects processor, use the effects loop instead of plugging
the guitar into the effects and then into the amp. To use the EFFECTS LOOP, plug the INPUT of your
effects into the SEND jack and the OUTPUT of your effects into the RETURN jack. Use shielded cables,
not speaker cables. It’s normal to have a slight gain reduction of several dB with some effects units.
However, the amp has plenty of gain to overcome any loss.
15. FS22 FOOTSWITCH
Most foot pedals with 2 switches, a stereo cord and plug will work. However, Carvin’s FS22 is rec-
ommended because of the correct identification label on the foot switch. First, the channel SELECT
switch on the front panel must be selected to channel 1 before the footswitch will work. Now that you
are connected correctly, the channels and reverb can be switched remotely. If a hum is heard in the
speakers, the select switch is in the wrong position.
16. VOICED LINE OUT
The LINE OUT 1/4” jack is “CABINET VOICED” to prevent excessive bass or highs going to your
mixer. This greatly aids in sound quality because you do not have to move your mixer EQ setting to
the extreme. The 1.5 VAC output (reference to 100 watts output at 8 ohms) is more than adequate
to drive any professional mixer or power amp.
17. SPEAKER IMPEDANCE SWITCH
The IMPEDANCE SWITCH offers the selection of 4, 8 or 16Ωto match your speaker system. Set
the rear impedance switch to the following impedance: 8Ωfor Nomad, 8Ωfor the Bel Air™ combo
and 8Ωfor the 410 cabinet. In the case of adding another extension cabinet, set the impedance switch
to 4Ω..
18. SPEAKER JACKS
Two 1/4” SPEAKER JACKS are featured to operate several speaker systems at the same time. Move
the IMPEDANCE SWITCH to the correct setting. (Vintage 16™ has one 1/4” 8Ωjack for the internal
Celestion speaker.)
19. POWER MODE (Vintage 16™ only)
Shut the amp OFF before switching between the pentode 16w and the triode 5w mode.
HELP SECTION
a) FEEDBACK FROM THE LEAD CHANNEL
The VINTAGE TUBE SERIES will feedback when the LEAD volume, DRIVE, TREBLE and PRESENCE
are turned all the way up. Like other highly modified tube amps, this is normal. To help reduce feed-
back and noise, keep the DRIVE control set around 5 to 7 on the dial. Some of the best lead satu-
ration will be at around 5—not 10. Sometimes replacing V1 (12AX7A) can help reduce feedback.
b) TUBE REPLACEMENT GUIDE
It is not uncommon for tubes to malfunction during shipping. If your amp is not working properly,
please call or refer to the following replacement guide to replace tubes.
1) The 12AX7A preamp tubes are located in the following order on your chassis: V1, V2, V3, V4, V5.
To start with, V1 is located next to the outside of your chassis behind the output transformer. It
is recommended to turn your amp upside down to replace tubes. Replacing V1 will help reduce
feedback in channel 1. Replacing V2 and V3 can also help but V1 is the main tube to replace.
Replacing V4 will correct problems with the reverb system unless there is a defective reverb tank
or tank cables. If the power amp is not functioning, check or replace the EL84 power tubes and
check V5 by inserting a signal into the Effects RETURN jack. All tubes are keyed in the same
direction. In the Vintage 16™ V1 is the input tube, V2 is the Reverb tube, and V3 is the power tube.
2) The EL84 power tubes are located in the following order on your chassis: V6, V7, V8, V9. Normally
you’ll want to replace these tubes as a set. Please call for our latest prices. Sometimes you can
spot defective power tubes when they are glowing red-hot along with an audible hum in the speaker
when the amp is idling. If this happens, shut the amp down immediately. After they have cooled
down, push the hold-down clamp over the top of the tube and pull out to remove. It is recom-
mended to turn your amp upside down to replace tubes. All tubes are keyed in the same direc-
tion. Running defective power tubes could damage the amp. It is recommended that you have
a spare set of power tubes along with several 12AX7A preamp tubes.
98
7
15 16 17 18
120V 60 Hz
1A SLOW BLOW
60VA FUSE
3 POWER TUBES: EL84 3 PREAMP TUBES: 12AX7
POWER MODE
TRIODE 6 WATTS





NORMAL 15 WATTS
SPEAKER
8 OHM
9
8
7
5
6
1
11
18
10
19
VINTAGE 16™
Press firmly until cord clicks in.

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED
OR CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type described
in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-
ization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
This symbol is intended to
alert the user to the pres-
ence of uninsulated “dan-
gerous voltage” within the
product’s enclosure that may be of suf-
ficient magnitude to constitute a risk of
electric shock to persons.
This symbol is
intended to alert the
user to the presence of
important operating
and maintenance (servicing) instruc-
tions in the literature accompanying
the appliance.
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for ONE YEAR unless otherwise stated. Vacuum
tubes are guaranteed for 90 days. Carvin will service and supply all parts at no charge to the customer
providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN
DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL
INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn dri-
vers or speakers damaged by this unit. This warranty does not cover, and no liability is assumed, for
damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect
use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or implied.
No representative or person is authorized to represent or assume for Carvin any liability in connection
with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
When RETURNING merchandise to the factory, you may call for a return authorization number. Describe
in writing each problem. If your unit is out of warranty, you will be charged the current FLAT RATE for
parts and labor to bring your unit up to factory specifications.
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or power-
strip switches that may be turned off. Check the fuse. If a dark brownish color or no wire can be
seen within the glass tube, then replace. The amp may be perfectly fine but occasionally a fuse
may blow because of high AC voltage surges. After the fuse has been replaced with the proper
Slow Blow value and if the fuse fails again, the amp will require servicing.
2) NO OUTPUT with POWER LIGHT ON
Tubes damaged in shipping will be the primary reason for your amp to not function properly. Please
give us a call to help guide you through this simple repair.
3) KEEP YOUR AMP LOOKING NEW
Use a damp cloth to wipe the controls on the front & rear chassis panels. Wipe the black vinyl cov-
ering with a damp cloth.
REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL! THIS UNIT CON-
TAINS HIGH VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
Ref. # Description Carvin PN
B1 Junper, 0.5”, 0Ω51-00050
B2 Junper, 0.35”, 0Ω50-00035
B3 Junper, 0.5”, 0Ω51-00050
B4 Junper, 0.5”, 0Ω51-00050
B5 Junper, 0.5”, 0Ω51-00050
B7 Junper, 0.35”, 0Ω50-00035
B9 Junper, 0.5”, 0Ω51-00050
B10 Junper, 0.5”, 0Ω51-00050
B11 Junper, 0.35”, 0Ω50-00035
B12 Junper, 0.35”, 0Ω50-00035
B13 Junper, 0.35”, 0Ω50-00035
B14 Junper, 0.35”, 0Ω50-00035
B15 Junper, 0.35”, 0Ω50-00035
B16 Junper, 0.8”, 0Ω44-18000
B17 Junper, 0.5”, 0Ω51-00050
B18 Junper, 0.35”, 0Ω50-00035
B19 Junper, 0.5”, 0Ω51-00050
B20 Junper, 0.35”, 0Ω50-00035
B22 Junper, 0.35”, 0Ω50-00035
B23 Junper, 0.8”, 0Ω44-18000
B24 Junper, 0.35”, 0Ω50-00035
B25 Junper, 0.35”, 0Ω50-00035
B26 Junper, 0.35”, 0Ω50-00035
B27 Junper, 0.35”, 0Ω50-00035
B28 Junper, 0.35”, 0Ω50-00035
B29 Junper, 0.5”, 0Ω51-00050
B30 Junper, 0.5”, 0Ω51-00050
B31 Junper, 0.5”, 0Ω51-00050
B32 Junper, 0.8”, 0Ω44-18000
B33 Junper, 0.8”, 0Ω44-18000
B34 Junper, 0.5”, 0Ω51-00050
B35 Junper, 0.35”, 0Ω50-00035
B36 Junper, 0.35”, 0Ω50-00035
B37 Junper, 0.35”, 0Ω50-00035
B50 Junper, 0.5”, 0Ω51-00050
C1 Capacitor, Electrolytic, 10µF 50V, 20% 47-10051
C2 Capacitor, Poly, 0.01µF 100V, 10% 46-10312
C4 Capacitor, Poly, 0.001µF 100V, 10% 46-10212
C5 Capacitor, Poly, 0.033µF 100V, 10% 46-33312
C6 Capacitor, Ceramic, 120PF 500V, 10% 45-12152
C7 Capacitor, Poly, 0.01µF 100V, 10% 46-10312
C8 Capacitor, Electrolytic, 10µF 50V, 20% 47-10051
C9 Capacitor, Mylar, 0.047µF 400V, 10% 41-47342
C10 Not Used
C11 Capacitor, Electrolytic, 10µF 50V, 20% 47-10051
C12 Capacitor, Poly, 0.0033µF 100V, 10% 46-33212
C13 Capacitor, Ceramic, 250PF 500V, 5% 45-25152
C14 Capacitor, Ceramic, 560PF 500V, 10% 45-56152
C15 Not Used
C16 Capacitor, Ceramic, 0.0047µF 400V, 10% 41-47242
C17 Capacitor, Electrolytic, 10µF 50V, 20% 47-10051
C18 Capacitor, Mylar, 0.047µF 400V, 10% 41-47342
C19 Capacitor, Ceramic, 120PF 500V, 10% 45-12152
C20 Capacitor, Poly, 0.022µF 100V, 10% 46-22312
C21 Capacitor, Poly, 0.0022µF 100V, 10% 46-22212
C22 Capacitor, Poly, 0.0022µF 100V, 10% 46-22212
C23 Not Used
C24 Not Used
C25 Capacitor, Poly, 0.047µF 100V, 10% 46-47312
C26 Capacitor, Ceramic, 82PF 500V, 5% 45-82052
C27 Capacitor, Electrolytic, 10µF 50V, 20% 47-10051
C28 Capacitor, Mylar, 0.047µF 400V, 10% 41-47342
C29 Capacitor, Poly, 0.0022µF 100V, 10% 46-22212
C30 Capacitor, Electrolytic, 10µF 50V, 20% 47-10051
C31 Capacitor, Poly, 0.0022µF 100V, 10% 46-22212
C32 Not Used
C33 Capacitor, Poly, 0.001µF 100V, 10% 46-10212
C34 Capacitor, Ceramic, 56PF 500V, 5% 45-56052
C35 Capacitor, Poly, 0.047µF 100V, 10% 46-47312
C36 Capacitor, Mylar, 0.047µF 400V, 10% 41-47342
C37 Capacitor, Mylar, 0.047µF 400V, 10% 41-47342
Ref. # Description Carvin PN
C38 Capacitor, Electrolytic, 47µF 63V, 20% 47-47061
C39 Capacitor, Mylar, 0.047µF 630V, 10% 46-47362
C40 Capacitor, Electrolytic, 22µF 500V, 20% 42-20052
C41 Capacitor, Electrolytic, 22µF 500V, 20% 42-20052
C42 Capacitor, Electrolytic, 22µF 500V, 20% 42-20052
C43 Capacitor, Electrolytic, 22µF 500V, 20% 42-20052
C44 Capacitor, Electrolytic, 22µF 500V, 20% 42-20052
C45 Capacitor, Electrolytic, 2200uF 6.3V, 20% 47-22260
C46 Capacitor, Electrolytic, 2200uF 6.3V, 20% 47-22260
C47 Capacitor, Electrolytic, 2200uF 6.3V, 20% 47-22260
C48 Capacitor, Mylar, 0.047µF 630V, 10% 46-47362
C49 Not Used
C50 Capacitor, Poly, 0.0022µF 100V, 10% 46-22212
C70 Capacitor, Poly, 0.01µF 100V, 10% 46-10312
C71 Capacitor, Ceramic, 180PF 500V, 10% 45-18152
C72 Capacitor, Ceramic, 120PF 500V, 10% 45-12152
D1 Diode, 1N4745A 16V, 1W 60-47450
D2 Diode, 1N4745A 16V, 1W 60-47450
D3 Diode, 1N4745A 16V, 1W 60-47450
D4 Diode, 1N4745A 16V, 1W 60-47450
D5 Diode, 1N4003 200V, 1A 60-40030
D6 Diode, 1N4007A 1000V, 1A 60-10000
D7 Diode, 1N4007A 1000V, 1A 60-10000
D8 Diode, 1N4007A 1000V, 1A 60-10000
D9 Diode, 1N4007A 1000V, 1A 60-10000
D10 Diode, 1N4007A 1000V, 1A 60-10000
D11 Diode, 1N4007A 1000V, 1A 60-10000
D12 Diode, 1N4007A 1000V, 1A 60-10000
D13 Diode, 1N4007A 1000V, 1A 60-10000
D14 Diode, 1N4007A 1000V, 1A 60-10000
D15 Diode, 1N4007A 1000V, 1A 60-10000
D16 Diode, 1N4007A 1000V, 1A 60-10000
D20 Not Used
D21 Not Used
F1 Fuse Clips, (1 pair) 23-03529
Fuse 1AGC Fast 70-21010
F2 Fuse Clips, (1 pair) 23-03529
Fuse 10A Slow 70-22101
F3 Fuse Clips, (1 pair) 23-03529
Fuse 1AGC Fast 70-21010
G1 Ferrite Bead 15-27430
H1A Cable 10” 2 conductor + Shield 05-00110
H2A Conn. Header, 2 Pin Vert, SHS 23-11002
H2B Conn. Header, 2 Pin Vert, SHS 23-11002
H3A Conn. Header, 4 Pin Vert, SHS 23-11004
H3B Conn. Header, 4 Pin Vert, SHS 23-11004
H5 Wire 10”, 18GA (Pair) 04-18010
H6 Wire 4”, 18GA (Pair) 04-18040
H7A Conn. Header, 2 Pin Vert, SHS 23-11002
H7B Conn. Header, 2 Pin Vert, SHS 23-11002
H8A Conn. Header, 2 Pin Vert, SHS 23-11002
H8B Conn. Header, 2 Pin Vert, SHS 23-11002
J1 Phone Jack, 1/4, 90° Rev Threaded Neck 21-01804
J2 Phone Jack, 1/4, 3 Pin Plastic, 24mm 21-06453
J3 Phone Jack, 1/4, 3 Pin Plastic, 24mm 21-06453
J4 Phone Jack, 1/4, 3 Pin Plastic, 24mm 21-06453
J5 Phone Jack, 1/4, 7 Pin Plastic Stereo, 24mm 21-06457
L1 Relay 3V PCB MNT, 5V DPDT 70-05303
L2 Relay 3V PCB MNT, 5V DPDT 70-05303
P1 Potentiometer, B100K, O Shaft, 16mm, RX250 90° 71-14052
P2 Potentiometer, B1MEG, O Shaft, 16mm, RX250 90° 71-14070
P3 Potentiometer, 25A25K, O Shaft, 16mm, RX250 90° 71-14050
P4 Potentiometer, B1MEG, O Shaft, 16mm, RX250 90° 71-14070
P5 Potentiometer, 5A500K, O Shaft, 16mm, RX250 90° 71-14060
P6 Potentiometer, B100K, O Shaft, 16mm, RX250 90° 71-14052
P7 Potentiometer, B1MEG, O Shaft, 16mm, RX250 90° 71-14070
P8 Potentiometer, 25A25K, O Shaft, 16mm, RX250 90° 71-14050
P9 Potentiometer, B100K, O Shaft, 16mm, RX250 90° 71-14052
P10 Potentiometer, B100K, O Shaft, 16mm, RX250 90° 71-14052
P11 Potentiometer, Trimmer, 20K PCB MTG 71-22012
P21 Potentiometer, 25A15K-C, O Shaft, 16mm, RX250 90° 71-14048
Ref. # Description Carvin PN
QC1 Spade Terminal, QC Vertical, 0.205 06-40045
QC2 Spade Terminal, QC Vertical, 0.205 06-40045
QC3 Spade Terminal, QC Vertical, 0.205 06-40045
QC4 Spade Terminal, QC Vertical, 0.205 06-40045
QC6A Spade Terminal, QC Vertical, 0.250 06-40050
QC6B Spade Terminal, QC Vertical, 0.250 06-40050
QC7 Spade Terminal, QC Vertical, 0.250 06-40050
QC8 Spade Terminal, QC Vertical, 0.250 06-40050
QC9 Spade Terminal, QC Vertical, 0.250 06-40050
QC13ASpade Terminal, QC Vertical, 0.250 06-40050
QC13BSpade Terminal, QC Vertical, 0.250 06-40050
QC14 Spade Terminal, QC Vertical, 0.250 06-40050
QC31 Spade Terminal, QC Vertical, 0.250 06-40050
QC32 Spade Terminal, QC Vertical, 0.250 06-40050
QC33 Spade Terminal, QC Vertical, 0.250 06-40050
QC35 Spade Terminal, QC Vertical, 0.250 06-40050
QC36 Spade Terminal, QC Vertical, 0.250 06-40050
QC37 Spade Terminal, QC Vertical, 0.250 06-40050
R1 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R2 Resistor, 1.5K, .35 Prep., 5% Carbon, 1/4W 50-15035
R3 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R4 Resistor, 150K, .35 Prep., 5% Carbon, 1/4W 50-15055
R5 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R6 Resistor, 1.5K, .35 Prep., 5% Carbon, 1/4W 50-15035
R7 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R8 Resistor, 1.5K, .35 Prep., 5% Carbon, 1/4W 50-15035
R9 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R10 Resistor, 4.7K, .35 Prep., 5% Carbon, 1/4W 50-47035
R11 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R12 Resistor, 47K, .35 Prep., 5% Carbon, 1/4W 50-47045
R13 Resistor, 1K, .35 Prep., 5% Carbon, 1/4W 50-10035
R14 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R15 Resistor, 47K, .35 Prep., 5% Carbon, 1/4W 50-47045
R16 Resistor, 10K, .35 Prep., 5% Carbon, 1/4W 50-10045
R17 Resistor, 22K, .35 Prep., 5% Carbon, 1/4W 50-22045
R18 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R19 Resistor, 220Ω, .35 Prep., 5% Carbon, 1/4W 50-22025
R20 Resistor, 2.2M, .35 Prep., 5% Carbon, 1/4W 50-22065
R21 Resistor, 47K, 0.8 Prep., 5% Carbon 1W 53-47045
R22 Resistor, 2.2M, .35 Prep., 5% Carbon, 1/4W 50-22065
R23 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R24 Resistor, 1.5K, .35 Prep., 5% Carbon, 1/4W 50-15035
R25 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R26 Resistor, 1M, .35 Prep., 5% Carbon, 1/4W 50-10065
R27 Resistor, 22K, .35 Prep., 5% Carbon, 1/4W 50-22045
R28 Resistor, 1.5K, .35 Prep., 5% Carbon, 1/4W 50-15035
R29 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R30 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R31 Resistor, 560Ω, .35 Prep., 5% Carbon, 1/4W 50-56025
R32 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R33 Resistor, 22K, .35 Prep., 5% Carbon, 1/4W 50-22045
R34 Resistor, 22K, .35 Prep., 5% Carbon, 1/4W 50-22045
R35 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R36 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R37 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R38 Resistor, 220K, .35 Prep., 5% Carbon, 1/4W 50-22055
R39 Resistor, 3.9K, .35 Prep., 5% Carbon, 1/4W 50-39035
R40 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R41 Resistor, 4.7K, .35 Prep., 5% Carbon, 1/4W 50-47035
R42 Resistor, 2.2K, .35 Prep., 5% Carbon, 1/4W 50-22035
R43 Resistor, 350Ω., SDOF, 10% Sand Bar,10W 56-35010
R44 Resistor, 100Ω, 0.35 Prep., 1% Metal, 1/4W 50-10021
R45 Resistor, 100Ω, 0.35 Prep., 1% Metal, 1/4W 50-10021
R46 Resistor, 10Ω, 0.5 Prep., 5% Carbon, 1/2W 52-10015
R49 Resistor, 100K, .35 Prep., 5% Carbon, 1/4W 50-10055
R50 Resistor, 1MEG, .35 Prep., 5% Carbon, 1/4W 50-10065
R57 Resistor, 4.7K, .35 Prep., 5% Carbon, 1/4W 50-47035
R60 Resistor, 56K, .35 Prep., 5% Carbon, 1/4W 50-56045
R61 Resistor, 56K, .35 Prep., 5% Carbon, 1/4W 50-56045
R62 Resistor, 350Ω, .35 Prep., 5% Carbon, 1/4W 50-35025
R63 Resistor, 350Ω, .35 Prep., 5% Carbon, 1/4W 50-35025
Ref. # Description Carvin PN
R64 Resistor, 56K, .35 Prep., 5% Carbon, 1/4W 50-56045
R65 Resistor, 56K, .35 Prep., 5% Carbon, 1/4W 50-56045
R66 Resistor, 350Ω, .35 Prep., 5% Carbon, 1/4W 50-35035
R67 Resistor, 350Ω, .35 Prep., 5% Carbon, 1/4W 50-35035
R70 Resistor, 2.2K, .35 Prep., 5% Carbon, 1/4W 50-22035
R71 Resistor, 10K, .35 Prep., 5% Carbon, 1/4W 50-10035
R72 Resistor, 470K, .35 Prep., 5% Carbon, 1/4W 50-47045
R73 Resistor, 22K, .35 Prep., 5% Carbon, 1/4W 50-22045
S1 Switch, DP3T Lift Tall Bat, PCB MTG 25-76286
Switch, Channel Select, SPST toggle, Chassis MTG 25-75801
Switch, Power, LG DPDT, Chassis MTG 25-31350
Switch, Stand-by, LG DPDT, Chassis MTG 25-31350
SPK1 Phone Jack, 1/4, 3 Pin Plastic, 24mm 21-06453
SPK2 Phone Jack, 1/4, 3 Pin Plastic, 24mm 21-06453
Vintage Tube 50, 120V Transformer, Chassis MTG 15-10640
Vintage Tube 50, Output Transformer, Chassis MTG 15-02066
V1 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube 12AX7A 65-00127
V2 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube 12AX7A 65-00127
V3 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube 12AX7A 65-00127
V4 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube 12AX7A 65-00127
V5 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube 12AX7A 65-00127
V6 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube EL84 65-00084
V7 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube EL84 65-00084
V8 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube EL84 65-00084
V9 Socket for 12AX7A/EL84 12VAC, 9 Pin, SIN/RUS 23-91632
Vacuum Tube, Type Tube EL84 65-00084
REPLACEMENT PARTS LIST (for circuit cards)