CARVIN 1584 User manual

SPEAKER CABLES
Our standard cable for speaker hookups is the PH50. This cable features 1/4”
plugs and 16 gauge copper wire. The PH50 is adequate for lengths up to 50’ under
normal use. You can DAISY-CHAIN up to one additional speaker per cable by using
the unused 1/4” OUTPUT” jack (right side) on your speaker jack plate. Be sure to
note the total impedance to the amp so it is not lower than it’s recommended
impedance. See Typical Loudspeaker Impedance Configurations.
Our professional SPK25, SPK50 & SPK100 cables feature Speakon™ lock-on
connectors with heavy 4 conductor 12 gauge copper wire. These cables are to be
connected in the same way as the PH50 with compatible amps.
PRECAUTIONS
1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate.
Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are
harmful to drivers causing failure which is not covered under warranty.
WARRANTY
CARVIN loudspeakers are covered by a ONE year limited warranty unless
otherwise stated. Warranty coverage is limited to original manufactures defects
only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn
cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC.
When returning defective driver(s), remove them from the enclosure to reduce
shipping costs . DO NOT stuff paper into the driver(s). Return pre-paid by UPS.
Include your address and description of the problem. Your driver(s) will be returned
COD for the cost of shipping and reconditioning if not covered under warranty.
MODEL 1584 SPEAKER SYSTEM SPECS:
Frequency Response: 50 Hz to 19 kHz ±3 dB
Useable Low Frequency
Bandwidth: 38 Hz (-10 dB)
Power Handling: 400 watts Continuous Program Power
Recommended Amp: 75 to 600 watts
Sensitivity: 100 dB SPL, 1 Watt @ 1 meter
Coverage Angles: 90° Horizontal, 45° Vertical
Nominal Impedance: 8Ω
Crossover Type: C1584 Constant Voltage
Input & Output Connectors: Two 1/4", two Speakon™
BIAMP Support: Yes—Panel Switch
Horn Driver Protection: Yes—Exciter Lamp
Woofer Enclosure Type: Vented Box
Enclosure Covering: Black Duratuff™
Dim/Wt: 22"W x 15.25"D x 31.5"H, 68 lbs.
Warranty: One Year, Extended Warranty available
Optional Cables: PH50, SPK25, SPK50, SPK100
Optional Vinyl Cover: CVS1584
1584 FREQUENCY RESPONSE
CARVIN ENGINEERING DATA 1584 SPEAKER SYSTEM INSTRUCTIONS
1584
Congratulations on your selection of the 1584 loudspeaker. The 1584 vented, 400
watt 3-way speaker enclosure will exceed the power and output of the competition
and it will sound better because of its superior design featuring a computer optimized
cabinet, advanced C1584 crossover, and the Pro Series speaker components. We
realize that for a loudspeaker to sound its finest, it must be a system of precisely
aligned components. With our matched 15“ woofer, 8“ midrange and titanium horn,
the 1584 is an outstanding system for a vast array of applications ranging from clubs
to outdoor use.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the best
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Keep your portion of the card and return the portion with your
name and comments to us.
SUGGESTIONS FOR OPTIMAL PERFORMANCE
Raise the enclosure to the ear level of your audience for greater coverage. To
help control feedback, use a graphic equalizer. Keep the speakers in front of the
microphone. Never direct the microphone towards the speaker. For greater
coverage, add a second speaker system 20° to 30° off axis.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
SERIES CONNECTION
16ΩTOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4ΩTOTAL IMPEDANCE
+
++
8ΩTOTAL
IMPEDANCE SERIES/PARALLEL
CONNECTION
8ΩTOTAL IMPEDANCE
+
+ +
+
+
+
+
8Ω8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
4Ω8Ω
8Ω
16Ω8Ω8Ω
REAR CONNECT PLATE
Two standard 1/4” phone
jacks and two Speakon™
connectors are featured. See
other side for hookup
diagrams.
12340 World Trade Drive, San Diego, CA 92128
[phone] [phone]
www.carvin.com
All manuals and user guides at all-guides.com
all-guides.com

MIXER POWER AMP
SPEAKER SYSTEM
OUT
MODE SWITCH: FULL RANGE
ADDITIONAL
SYSTEM
1588
SPK OUTINPUT
Toll Free 1-800-854-2235
USA
1
SPEAKER SYSTEM MODE SWITCH: BIAMP
5841
PROFESSIONAL SOUND REINFORCEMENT
MADE IN THE
USA
8 Ω 400 Watts
JACKS WIRED
PARALLEL IN FULL
RANGE MODE
Speakon™
1+SIGNAL
1–GROUND
2+ & 2–
NOT USED
FULL RANGE–INPUT
BIAMP SW–HI FREQ. INPUT 8ΩFULL RANGE –PARALLEL BIAMP SW–LOW FREQ. INPUT 8Ω
BIAMP
FULL
RANGE
5841
PROFESSIONAL SOUND REINFORCEMENT
MADE IN THE
USA
8 Ω 400 Watts
JACKS WIRED
PARALLEL IN FULL
RANGE MODE
Speakon™
1+SIGNAL
1–GROUND
2+ & 2–
NOT USED
FULL RANGE–INPUT
BIAMP SW–HI FREQ. INPUT 8ΩFULL RANGE –PARALLEL BIAMP SW–LOW FREQ. INPUT 8Ω
BIAMP
FULL
RANGE
ELECTRONIC CROSSOVER
MIXER
OUT
IN (Set FREQ 600Hz) HILOSUB
MIXER POWER AMP
SPK OUTINPUT
USA
1
HOOKUP DIAGRAMS
NORMAL FULL RANGE HOOKUP
BI-AMP HOOKUP
All manuals and user guides at all-guides.com