Casablanca Nouvelle User manual

NOUVELLE
OWNERS MANUAL

1
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
•Thebladesin each packarematchedforequal
weight to assure smooth fan operation. If
more than one fan is being installed, be care-
ful not to mix blades from different cartons.
•Inspect the contents of your carton for pos-
sible shipping or handling damage and report
any such damage directly to your authorized
Casablanca dealer.
•It is always a good idea to have an assistant
to help with the installation.
•When cleaning, painting, or working near
yourfan,bevery careful ofthefanandblades.
Always turn the power OFF to the ceiling fan
before servicing it or working on it.
•Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
•Never operate a fan that has been damaged
in any way. Contact Casablanca Fan Company
by calling 1-888-227-2178, or contact your
local authorized Casablanca dealer for assis-
tance in obtaining service.
CONTENTS
SAFE USE
INTRODUCTION ..........................................................................................................................................1
MOUNTING RECOMMENDATIONS ..................................................................................................................2
FAN INSTALLATION - GETTING STARTED ......................................................................................................3
ADAPTOR PLATE INSTALLATION...................................................................................................................4
FAN PREPARATION .....................................................................................................................................5
INSTALLATION & WIRING............................................................................................................................6
LIGHT FIXTURE INSTALLATION ...................................................................................................................9
NO LIGHT FIXTURE OPTION.......................................................................................................................10
INTELI•TOUCH CONTROL OPERATION.........................................................................................................12
TROUBLESHOOTING ..................................................................................................................................15
P/N 9643010 REV. B P/D FEB00PDG
18″
84″
74″
READ AND SAVE THESE INSTRUCTIONS
•All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-
cian should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
•This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
•Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation; therefore, before attempting to install and operate your Casablanca
fan, read this owner’s manual completely and carefully. Retain this manual for future reference.
SAFETY FIRST
BEFORE YOU START
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off
at the circuit breaker or fuse box before attempting any installation procedure.

2
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
SLOPED CEILING INSTALLATIONS
MOUNTING RECOMMENDATIONS
7′MINIMUM
Pole Length
Standard
Standard
6″
12″
12″
18″
24″
36″
48″
Ceiling Height
8′
8′6″
9′
9′6″
10′
11′
12′
13′
14′
Suggested Extension Pole Lengths
When to Use Extension Poles
Forbest performanceandbestappearance,
an extension pole should be used with
your Casablanca fan when installing on
high (cathedral) ceilings or sloped ceil-
ings. Casablanca offers standard poles in
increments of 6″up to 5′. Custom poles
are available in lengths up to 10′. See your
Authorized Casablanca Dealer for details.
32°
BLADES MUST BE A
MINIMUM OF 7′
ABOVE THE FLOOR
EXTENSION
POLE
MAXIMUM
HANG-TRU®
ANGLE 32º
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount-
ing recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7′above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18″from the wall in order to
provide sufficient clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52″fan even in
smaller rooms. For very large rooms, two fans may be needed.
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards
to purchasing a “Slope Ceiling Adaptor.”
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.

3
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping
cartons and check them against the parts listed in instructions.
Before discarding packaging material, be certain that all parts have been removed.
CEILING HARDWARE
CROSSBAR
MOUNTING
BRACKET
GETTING STARTED
Carton Contents
The fan carton contains the fan body, warranty card, owner's
manual,andalltheparts necessary (exceptblades)toassemble
and install your Casablanca ceiling fan. These parts are shown
at the start of each installation section. Before you start, go
through this Owner’s Manual and confirm that you have all the
parts shown in each section.
SCREW 21/4″ (2)
SCREW 1″(2)
WIRE NUT (4)
GETTING STARTED - CONTINUED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
Warning: To reduce the risk of fire, electrical shock, or
personal injury, mount to outlet box marked accept-
able for ceiling fan support.
Using Existing Ceiling Fixture Outlet Box
Afterturning thepower OFFat itssource(eithercircuitbreaker
or fuse box), lower the old fixture and disconnect the wiring.
Check the ceiling fixture outlet box to be sure that it is a UL
listed ceiling box for ceiling fan applications. If it is not, a
new box must be installed.
Be sure to use only genuine Casablanca blades. The blade
shrink wrap holds 5 blades of matched weight. If more than
one fan is being installed, be sure not to mix blade sets.
CAUTION: When removing the shrink wrap, be careful not
to scratch the blades.
FLAT
WASHER
(2)
ADDITIONAL HARDWARE
SUPPORT INSTALLATION PARTS
CANOPY
ADAPTOR
PLATE
LAG SCREW
3/8” #7 X 5” (1)
LARGE
FLAT WASHER
3/8” (1)
CANOPY HARDWARE
CANOPY
CANOPY
HATCH CANOPY LOCK WASHER
#8 (4)
CANOPY SCREW
8-32 X 41/8”(4)
R
PHILLIPS
SCREWDRIVER
NOUVELLE™

4
ADAPTOR PLATE INSTALLATION
JOIST
Step 2. Route the outlet box wires through the 1/2″ diam-
eter outer hole of the canopy adaptor plate. Attach the
crossbar and canopy adaptor plate to outlet box with screws
provided.
Step 3. With the large washer attached, pass the lag screw
through the center hole of canopy adaptor plate and screw
into guide hole. Tighten until outlet box is firmly mounted
to beam. This box must be firmly secured to the ceiling. We
recommend that the ceiling fixture outlet box be of suffi-
cient capacity enabling it to support the weight of fan and
light fixture under any conditions.
LAG
SCREW
LAG SCREW INSTALLATION
1/2″DIAMETER
OUTER HOLE
CEILING
WIRING
CROSSBAR
MOUNTING
BRACKET
FLAT
WASHER
GREEN
GROUND
WIRE
CEILING FAN
APPROVED
WIRING BOX
RIDGE
SIDE
DOWN
APPROVED
OUTLET BOX
HARDWARE
Note: After removing the old fixture, check the outlet box
to insure that it is supported by a joist or beam across its
upper surface. If not, a 2" x 4" stud must be installed.
Proceed with installation as follows:
Step 1. Remove the knockout plug in the center of the outlet
box or drill a 1/2″hole for the lag screw to pass through. Then
drill a 1/4″guide hole into the joist or beam to a depth of 3″.
LARGE
WASHER
NOUVELLE™
WARNING!
SUPPORT DIRECTLY TO
BUILDING STRUCTURE.
CAUTION: To reduce the risk of personal injury,
use only the mounting hardware provided with
the approved outlet box to install the crossbar
mounting bracket.

5
FAN PREPARATION - HARDWARE
TIP: Use masking tape to temporarily hold
the motor cover to the downrod ball; this
will ease downrod installation.
FAN PREPARATION 2
Note: For the next 5 prepara-
tion steps it is convenient to
leave the fan body in the lower
carton styrofoam as it provides
a stable work-top.
DOWNROD &
BALL ASSEMBLY
Preparation Step B. Slide the motor cover onto
the Perma•Lock™ downrod assembly as shown.
MOTOR
COVER
DOWNROD
&
BALL ASSEMBLY
GROUND
WIRE
Step 4. Attach the canopy to the cross bar with
three (3) of the 8-32 X 41/8″canopy screws and
#8 lock washers, hand tighten until snug against
the ceiling. On sloped ceilings, align the canopy
hatch opening toward the top or peak of the
room. Your Casablanca fan may be installed on
a vaulted or cathedral ceiling in the same man-
ner as described for a flat ceiling.
The Hang-Tru®mounting system makes it pos-
sible to hang your fan on ceilings sloped up to
a 32°angle.
CANOPY INSTALLATION
CANOPY
SCREW
CANOPY
LOCK
WASHER
CANOPY
FAN PREPARATION 1
FAN
BODY
M
O
T
O
R
S
H
I
E
L
D
L
E
A
V
E
I
N
P
L
A
C
E
U
N
T
I
L
I
N
S
T
A
L
L
A
T
I
O
N
A
N
D
W
I
R
I
N
G
C
O
M
P
L
E
T
E
R
E
M
O
V
E
T
H
I
S
S
H
I
E
L
D
W
H
E
N
I
N
S
T
A
L
L
A
T
I
O
N
I
S
C
O
M
P
L
E
T
E
CAUTION
DAMP LOCATION RATED FANS
REQUIRE A GROUND FAULT INTERRUPTER (GFI)
USE A WEATHER PROOF OUTLET BOX
PROPERLY CONNECT GROUND WIRES
USE ONLY UNDER A WEATHER
PROOF STRUCTURE
DANGER
IT IS IMPERITIVE THAT THE LOCKSCREW
BE SET TIGHTLY AGAINST THE DOWNROD
THREADS AFTER FAN IS ASSEMBLED
FAILURE TO DO SO WILL CAUSE FAN TO FALL
TIGHTEN
LOCKSCREW TIGHTEN
LOCKSCREW
INSTALLER
GIVE THIS TAG TO THE
CONSUMER AFTER
INSTALLATION COMPLETE
INSTALLER
CONFIRM LOCKSCREW
IS PROPERLY TIGHTENED
DO NOT OIL SEALED BEARINGS!
P/N 1942640 SRB4/96
MOTOR
SHIELD
MOTOR
WIRES
Preparation Step A. Remove the
motor shield from the top of the
motor, note the caution message
and read the instructions care-
fully.
CANOPY
HATCH
OPENING
PHILLIPS
COUNTERSUNK SCREW
8-32 X 9/16″
MOTOR COVER
NOUVELLE™
Note: Write down the
Serial Number and
the model number for
future reference.
ALLEN SET SCREW
1⁄4-20 x 1⁄4"
(PRE-INSTALLED)
3mm
ALLEN WRENCH

6
Step 5. To hang the fan body in the canopy,
hold the fan body firmly and insert the nylon
ball into the canopy opening. Check that no
wires were pinched. Rotate the fan body until
the slot in the nylon ball engages the canopy
pin opposite the canopy hatch opening.
HANGING THE FAN
CANOPY
PIN
SLOT
BALL
DOWNROD & MOTOR COVER INSTALLATION
ALLEN SET SCREW
DOWNROD
&
BALL
ASSEMBLY
Preparation Step B. Route the black and white
wires from the motor through the downrod and
ball assembly. Make certain that you do not
scrape the insulation.
Preparation Step C. Using the provided allen
wrench,unscrew the allen setscrewuntilitclears
the inside of the motor coupling. Screw the
downrod into the motor coupling until tight.
Preparation Step D. Using the provided allen
wrench, tighten the allen set screw to ensure
safe operation of your fan.
MOTOR
COUPLING
TAPERED
THREAD
MOTOR
WIRES GROUND
WIRE
Preparation Step E. Align the motor cover to
allow the four 8-32 X 3/8″ (4) Phillips counter-
sunk screws to be installed.
Hand tighten securely
MOTOR
COVER
MOTOR WIRES
&
DOWNROD
GROUND
PHILLIPS
COUNTERSUNK
SCREW
HOUSE WIRING
&
CROSSBAR
GROUND
CANOPY
CAUTION: Failure to properly tighten the
downrod could result in the fan falling.
CAUTION: Failure to properly tighten
the downrod in the motor coupling and
securely tightening the locking bolt
could result in the fan falling during
normal operation!
NOUVELLE™

7
Step 7. Tuck the wires into the canopy, wire
nuts pointed upwards, the WHITE and GREEN
wires on the opposite side from the BLACK wires.
Keep all wires clear of the canopy opening.
Step 9. If necessary, straighten the fan, then
check to ensure that there is no movement be-
tween the canopy and ceiling or ball and
downrod.
Step 8. Installcanopyhatchwith the lastcanopy
screw and lock washer. To do this, partially in-
sert the canopy screw and lock washer before
aligning the hatch on the canopy.
CANOPY
HATCH
CANOPY HATCH INSTALLATION
CANOPY ELECTRICAL CONNECTIONS
Step 6. Connect the fan wires to the outlet box
wiring by placing the bare ends of the wires to-
gether and then securing with a wire nut.
Connect in this order:
• GREEN leads from mounting plate and fan
to GROUND conductor of power source.
Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire
in ceiling fixture outlet box.
Secure with wire nut.
• BLACK wire from fan to black POWER wire
in ceiling fixture outlet box.
Secure with wire nut.
2 BLACK
WIRES
2 WHITE
WIRES
3 GREEN
WIRES
CANOPY
SCREW
CANOPY
WASHER
WIRE DRESSING
Inspect each wire nut and ensure that no bare
wire is visible; pull on each wire to test the con-
nection is mechanically sound.
TIP: Have an assistant tilt the fan
away from the hatch side of the
canopy.
NOUVELLE™
WIRENUT

8
FELT WASHER
(4 PER BLADE)
BLADE SCREW
(4 PER BLADE)
Step 10. Attach the blades
to the blade holders with
four of the flat head 10-24
X 9/16″blade screws and #10
felt washers provided.
Hand tighten securely.
BLADE & BLADE HOLDER INSTALLATION
BLADE HOLDER SCREW
(2 PER BLADE HOLDER)
BLADE HOLDERS & HARDWARE
BLADE HOLDER SCREW
COUNTERSUNK PHILLIPS
12-24 X 5/8″(2 PER BLADE)
BLADE HOLDER FELT WASHER
#10 (4 PER BLADE)
BLADE SCREW
FLAT HEAD
10-24 X 7/16″(4 PER BLADE)
Step 11. Attacheach blade/
blade holder assembly to the
flywheel.
Tighten securely by hand
only.
4/5 Blade Combination Flywheel
Your Casablanca fan includes our 4/5 combination fly-
wheel. This flywheel accommodates your preference to
use either 4 or 5 blades on your fan. If you desire a 4-
blade fan, locate the square counterbores on the fly-
wheel and use these threaded holes to mount the blades.
If you desire a 5-blade fan, locate the round counterbores
on the flywheel and use these threaded holes.
= 4-blade mounting hole = 5-blade mounting hole
NOUVELLE™

9
Step 12. Remove the wire nuts on the BLACK and WHITE
wires from the fan. If necessary remove the insulation
from the last 1/2” of each wire (fan and light fixture).
Step 14. Attach the switch housing wires to the light
fixture wires by placing the bare ends of the wires to-
gether and then securing with a wire nut. Connect in
this order:
Step 13. Have an assistant hold up the light fixture
until it is close to the adaptor ring.
• WHITE wire from fan to WHITE wire from
light fixture. Secure with wire nut.
• BLACK wire from fan to BLACK wire from
light fixture. Secure with wire nut.
Inspect each wire nut and ensure that no bare wire is
visible; pull on each wire to test the connection is
mechanically sound.
LIGHT FIXTURE INSTALLATION
LIGHT FIXTURE ELECTRICAL CONNECTIONS
WIRENUT
LIGHT FIXTURE
SCREW
LIGHT FIXTURE HARDWARE
2 BLACK
WIRES
2 WHITE
WIRES
LIGHT
FIXTURE
ADAPTOR
RING
Step 15. Lift the light fixture
assembly, making sure not to
pinch the wires, and align the
three holes in the side of the
fixture with the three threaded
holes in the adaptor ring and
installthethree (3) 6-32X 5/16″
Phillips screws.
Hand tighten securely.
LIGHT FIXTURE SCREW
PHILLIPS COUNTERSUNK
6-32 X 5/16″(3)
NOUVELLE™
CAUTION: Before installing light fixture check
that the light fixture is securely tightened
to the lower switch housing.
ASSEMBLY
NUT
LIGHT
FIXTURE
LOWER
SWITCH
HOUSING
CHECK THAT THESE
LOCKNUTS AND THE
ASSEMBLY NUT ARE
VERY TIGHT
TIGHTEN WITH A
WRENCH IF REQUIRED
IF NOT INSTALLING LIGHT FIXTURE SKIP TO STEP 19

10
Step 16. Install three finger
screws into each light fitter.
Turn only once or twice.
Step 17. Position the shade
fully in the fitter and tighten
each finger screw two turns
each in rotation until the
shade is centered in the fit-
ter. Check that the shade is
captured by the finger screws
by lightly pulling on the
shade.
Hand tighten the finger
screws securely.
Repeat for each shade.
Step 18. Install the light
bulbs. Replace bulbs only
withtheexacttypeandwatt-
age.
LIGHT SHADE & BULB INSTALLATION
Step 19. Remove the locknut
securing the light fixture to
the lower switch housing.
Save locknut and fixture for
future use.
LIGHT SHADE & BULB HARDWARE
FINGER SCREW
(3 PER SHADE)
LIGHT
SHADE
NO LIGHT FIXTURE OPTION - FIXTURE REMOVAL
LOCKNUT
60 WATT BULB
LOWER
SWITCH
HOUSING
LIGHT
FIXTURE
FINGER SCREW
(3 PER SHADE)
THIS COMPLETES YOUR INSTALLATION. FOR OPERATIONAL CONTROLS, PLEASE SEE PAGE 12.
Note: Check the finger screws peri-
odicallyas theywill loosen andcause
operating noise.
NOUVELLE™

11
NO LIGHT FIXTURE OPTION - HARDWARE ASSEMBLY
NO LIGHT FIXTURE OPTION - HARDWARE
LOWER SWITCH
HOUSING CAP
THREADED BUTTON
Step 20. Line up the center
holes of the cap and lower
switch housing to allow the
threadedbutton to beinstalled.
Hand tighten securely
NO LIGHT FIXTURE OPTION - INSTALLATION
NO LIGHT FIXTURE OPTION - INSTALLATION HARDWARE
LOWER SWITCH
HOUSING CAP
THREADED
BUTTON
LOWER SWITCH
HOUSING
LIGHT FIXTURE
SCREW
Step 21. Alignthethreeholes
in the side of the fixture with
the three threaded holes in
the adaptor ring and install
the three (3) 6-32 X 5/16″
Phillips screws.
Hand tighten securely.
LIGHT FIXTURE SCREW
PHILLIPS COUNTERSUNK
6-32 X 5/16″(3)
NOUVELLE™

INTELI•TOUCH ♦♦
♦♦
♦SINGLE W-32 INSTALLATION
The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the
following precautions must be observed:
1. Use only the Casablanca W-32 wall control.
2. Do not use any additional control with your Inteli-Touch
fan (for example, dimmer, fan speed control, etc.).
3. Do not use more than one fan per wall control.
4. No other light fixtures or electrical appliances may be con-
nected on the circuit controlled by the W-32 wall control.
INTELI•TOUCH ♦♦
♦♦
♦DUAL W-32 INSTALLATION
W-32 is used to describe either white (-11) or ivory finish.
1. Remove the screws and switch plate from the existing
switch box.
2. Remove the screws holding the switch in the switch box.
3. Pull the existing switch from the switch box to expose the
wire connections.
4. Remove the two wires from the switch.
5. Connect the two wires just removed from the switch to
the W-32 wall control black wire and black/white stripe
wire. Secure these connections with wire nuts.
6. Install the W-32 in the wall box with the two long screws
provided.
7. Install the wall plate with the two color matched screws.
R
R
SWAP THESE TWO WIRES
WHEN NECESSARY
(SEE NOTE BELOW)
END
OF
LINE
IN
LINE
To control the fan and lights from two locations (a
three-way circuit), use 2 W-32 wall controls.
1. Remove the screws and switch plate from the ex-
isting switch box and the screws holding the switch
in the switch box.
2. Pull the existing switch from the switch box to
expose the wire connections.
3. Determine which wire is connected to the common
terminal of the 3-way switch. (The terminal will be
marked on switch).
4. Remove the wire from the common terminal of the
3-way switch. Connect this wire to the remaining
black/white striped wire on the W-32 control. Se-
cure this splice with a wire nut.
5. Remove the two remaining wires from the 3-way
switch. Connect one of these wires to a black wire
on the W-32 control. Secure the splice with a wire
nut. The remaining wire is to be connected to the
other black wire on the W-32. Secure the splice
with a wire nut.
6. Install the W-32 in the wall box with the two long
screws provided.
7. Install the wall plate with the two short color-
matched screws provided.
8. Installation of the second W-32 control is identi-
cal. Repeat steps 1 through 7.
INTELI•TOUCH© INSTALLING THE W-32 WALL CONTROL
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
NOTE: If wall control operation is reversed (fan switch controls
lights and light switch controls fan) turn off the power at the breaker
or fuse panel, then swap the two W-32 black/white stripe wires.
NOTE: If wall control operation is reversed (fan switch controls
lights and light switch controls fan) turn off the power at the breaker
or fuse panel, then swap the two W-32 black/white stripe wires.
R
12

13
INTELI•TOUCH OPERATION ♦POWER
+
+++
Programmed into every Inteli-Touch Series fan is an Auto-
matic Demonstration Program. It can be used to fully
demonstrate and test the operation of the fan.
To enter the demonstration program:
1. Turn off for at least three seconds. This will
clear the fan memory ready for programming.
2. Turn on.
3. Immediately operate the buttons in the following se-
quence:
FAN - LIGHT - FAN - LIGHT - FAN
A multi-tone signal will verify the start of the test program
which proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short
time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will
continue to repeat until the is turned off for more
than three seconds, cancelling the program.
The button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light level.
INTELI•TOUCH OPERATION ♦SPEED CONTROL
R
FAN CONTROL
ON - OFF:
A momentary press
of the FAN button
CHANGE SPEED:
Press and hold FAN
button longer than
one second
There are six individual speed settings for the fan; each speed is indicated by
an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled . The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the button is used. To maintain this level of speed,
turn the fan on by pressing less than one second. To lower speed,
turn fan off, then on by pressing and holding the button until the
desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the button until the desired speed is reached,
then release it. INTELI•TOUCH OPERATION ♦REVERSING AIRFLOW
The direction of airflow can be changed from downward to
upward or from upward to downward.
To reverse the airflow:
1. Make sure the is on.
2. Press the button.
Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
INTELI•TOUCH OPERATION ♦LIGHT
R
LIGHT CONTROL
ON - OFF:
A momentary press of
the LIGHT button
CHANGE BRIGHTNESS:
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
SECOND
To turn the lights off and on, press and release the button for less
than one second.
To vary the light brightness:
1. With lights off, press and hold the button. After one second the
lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the button is used. To
maintain this level of brightness, press the button for less than
one second. To lower the brightness, turn the lights off, then press and hold
the button until the desired brightness level is reached. When the
light is on, you may increase the brightness level by pressing and holding
the button until the desired level is reached, then release it.
AUTOMATIC DEMONSTRATION PROGRAM
R

14
The Light-Minder program automatically turns OFF the fan mounted lights after
two hours.
To enter the Light-Minder Program:
1. Turn the OFF for at least three seconds.
2. Turn the ON.
3. Immediately operate the buttons in the following sequence:
+++
4. A series of tones indicates this command has been accepted.
The fan and light will operate normally using the buttons to turn them on and off.
But, if the lights are left on, they will automatically shut off after two hours. To
cancel the Light-Minder Program, turn the off for three seconds.
INTELI•TOUCH OPERATION ♦SAFE-EXIT®PROGRAM
The Safe-Exit Program gives you about thirty seconds of light when you turn
the lights off, enabling you to exit your home before the lights go out.
To enter the Safe-Exit Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
+++
After you hear the confirming audio
tones from the fan - immediately press
4. The lights will blink to indicate this command has been accepted.
The lights will stay on for twenty seconds and then begin to dim. After a
total of thirty seconds has elapsed, the lights will be off completely. To
cancel the Safe-Exit Program, turn the off for three seconds.
INTELI•TOUCH OPERATION ♦HOME-SAFE®PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
+++
4. A tone and flashing light indicate this command has been accepted.
This program overrides all manual control of lights and fan. The lights will now be
automatically cycled on and off in a controlled sequence as follows: On 1 hour, off
1/2hour, on 2 hours, off 1 hour, on 1/2hour then off 2 hours.
This seven hour pattern will repeat continuously so that a different pattern of
lighting is seen each day of the week.
To cancel the Home-Safe Program, turn the off for three seconds.
INTELI•TOUCH OPERATION ♦FAN-MINDER™PROGRAM
The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the
speed of the fan each two-hour interval to compensate for the cooling night air.
To enter the Fan-Minder Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
+++
4. The fan controller will respond with three descending tones. A timer is now initiated and the fan
will reduce one speed for each two-hour interval. The fan will not, however, descend below the
second lowest speed.
To cancel the Fan-Minder Program, turn the off for three seconds. You may increase the fan
speed by pressing and holding the button until the desired speed is reached, then release it.
The fan will again reduce one speed for each 2 hour interval.
INTELI•TOUCH OPERATION ♦LIGHT-MINDER®PROGRAM
Note: Both Light-Minder and Safe-Exit
programs can run at the same time,
however the dimmer cannot be used,
the light may only be turned ON/OFF.
R

15
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accu-
mulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture pol-
ishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
PROBLEM POSSIBLE REMEDIES..
NO FAN OR LIGHT Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
FAN WOBBLES OR SHAKES Be sure canopy pin is properly set into the slot on the ball
EXCESSIVELY Check the screws holding the blade holders to the fan motor. Tighten as necessary.
Check the angle of the blades to make sure that a blade holder has not been bent during installation.
FAN NOISY DURING Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
OPERATION Tighten canopy screws and mounting plate assembly.
Tighten the blade to bladeholder screws and blade holders to flywheel.
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or
have fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD Let fan run at high speed for two (2) hours
DOES NOT RUN ON If new, “break-in”may be required - run at higher speed for several days
LOW SPEED
LIGHTS FLASH OR BLINK DURING OPERATION OF W-32 WALL CONTROLS/FAN MAY ROTATE OR MAKE AUDIBLE TONES DURING
OPERATION OF THE W-11 AND W-12 WALL CONTROLS: Normal operation.
WHEN AC POWER IS TURNED ON FOR THE FIRST TIME, THE LIGHTS OPERATE NORMALLY, BUT W-32 WALL CONTROL OPERATION IS
REVERSED: FAN BUTTON OPERATES THE LIGHTS; LIGHT BUTTON OPERATES THE FAN: Reverse the 2 black and white striped wire
connections.
FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES (CHANGING SPEED OR INTENSITY), WALL CONTROL OPERATION IS INTER-
MITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit board assembly.
INTELI•TOUCH
R

17
©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S. PATENT PENDING PRINTED IN ROC
761 CORPORATE CENTER DRIVE • POMONA, CA 91768
TOLL FREE: 888-CASA-1ST (227-2178)
www.CasablancaFanCo.com