Casablanca Stealth User manual

1
Stealth ®
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
18″
84″
70″
•The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, be careful not to
mix blades from different cartons.
•Inspect the contents of your carton for possible
shipping or handling damage and report any such
damage directly to your authorized Casablanca
dealer.
•It is always a good idea to have an assistant to help
with the installation.
•When cleaning, painting, or working near your fan,
be very careful of the fan and blades. Always turn
the power OFF to the ceiling fan before servicing
it, working on it, or replacing light bulbs.
•Never insert anything into the path of the fan blades
while the fan is in operation.
 
•Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling toll free 1-888-227-2178, or contact your
local authorized Casablanca dealer for assistance
in obtaining service.
READ AND SAVE THESE INSTRUCTIONS
SAFE USE
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
SAFETY FIRST
BEFOREYOU START
PN 3243Z HN1209
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off
at the circuit breaker or fuse box before attempting any installation procedure.
• CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local electrical
-

or transformer-supplied appliance..
 
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum

is 1.0 amps or 100 watts of lighting.
•Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light xtures, and accessories.
CONTENTS
INTRODUCTION 1
mOUNTINg ReCOmmeNDaTIONs 2
PRePaRaTION INsTRUCTIONs 3
faN INsTaLLaTION 4
CONTROL feaTURes:
INTELI•TOUCH OPERATION 8
INTELI•TOUCH TROUBLESHOOTING 16

2
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted
in the back of this manual, it provides you with a simple
‘go’ or ‘no-go’ for installing your fan on a sloped ceiling.
SLOPED CEILING INSTALLATIONS
MOUNTING RECOMMENDATIONS
7’ MINIMUM
Pole Length
Standard
Standard
6″
12″
12″
18″
24″
36″
48″
Ceiling Height
8′
8′6″
9′
9′6″
10′
11′
12′
13′
14′
Suggested Extension Pole Lengths
When to Use Extension Poles
For best performance and best ap-
pearance, an extension pole should be
used with your Casablanca fan when
installing on high (cathedral) ceilings
or sloped ceilings. Casablanca offers
standard poles in increments of 6″up
to 5′. Custom poles are available in
lengths up to 9’.9” See your Authorized
Casablanca Dealer for details.
32°
BLADES MUST BE A
MINIMUM OF 7’
ABOVE THE FLOOR
EXTENSION
POLE
MAXIMUM
HANG-TRU®
ANGLE 32º
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air
circulation, and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these
mounting recommendations as you decide where to install your Casablanca fan.
 ′
 
 ″from the wall in order to provide

 
 
from pool cues.
              
blades.
 

Fan Size
Variable fan speed capability permits the use of a full-size 52″fan even in
smaller rooms. For very large rooms, two fans may be needed.
EXAMPLE 1

It is OK to install your fan.
EXAMPLE 2

slope that will allow the fan to hang
straight down. It is OK to install
your fan.
EXAMPLE 3

Your fan will not hang straight down,
an adaptor is necessary. Contact your
local Authorized Casablanca Dealer in
regards to purchasing a “Slope Ceiling
Adaptor.”
Note: Fan may wobble or vibrate
if pole length is not long enough
and inside blade is too close to
downslope or side wall. Extending
pole length will usually solve
problem.

3
Stealth ®
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and
check them against the parts listed here. Before discarding packaging material, be certain that all parts have
been removed.
STEALTH INSTALLATION INSTRUCTIONS
FAN PREPARATION
PERMA•LOCK™ HARDWARE
DOWNROD & BALL
ASSEMBLY
ALLEN SET SCREW
1⁄4-20 x1⁄4”
(PRE-INSTALLED) 1/8”
ALLEN WRENCH
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
PermaLock™ downrod and ball assembly.
Step B. Using the provided allen wrench, loosen the set
screw several turns to allow installation of the downrod.
Thread the downrod into the motor coupling until it stops
turning, this will take at least four and a half full turns.
Step C. Securely tighten the set screw with the provided
allen wrench to ensure safe operation of your fan.
Tip: The downrod has a tapered
thread that is designed to lock com-
pletely when correctly installed.
CAUTION: Failure to fully lock in the downrod
before securely tightening the allen set screw may
cause the fan to separate from the downrod during
normal operation!
MOTOR
COUPLING
TAPERED
THREAD
MOTOR
WIRES
GROUND
WIRE
ALLEN
SET SCREW
DOWNROD
& BALL
ASSEMBLY

BEFORE STARTING THE INSTALLATION OFYOUR CEILING FAN, IN-
STALL THETHREADED DOWNROD INTOTHE MOTOR COUPLING AND
LOCK THE ASSEMBLY

4
CROSSBAR MOUNTING BRACKET INSTALLATION
JOIST
CEILING
WIRING
CROSSBAR
MOUNTING
BRACKET
FLAT
WASHER
GREEN
GROUND
WIRE
CEILING FAN
APPROVED
WIRING BOX
RIDGE
SIDE
DOWN
APPROVED OUTLET
BOX
HARDWARE

box to insure that it is supported by a joist or beam
across its upper surface. If not, a 2” x 4” stud must
be installed.
Step 1. Remove the knockout plug in the center of the
outlet box or drill a 1/2″hole for the lag screw to pass
through. Then drill a 1/4″guide hole into the joist or beam
to a depth of 3″.
Step 2. Route the outlet box wires through the keyhole
slot of the crossbar mounting bracket as shown. Attach the
crossbar mounting bracket to outlet box with screws pro-
vided, assuring that the outlet box wires are not pinched
by the washer.
CAUTION: To reduce the risk of personal
injury, use only the mounting hardware pro-
vided with the approved outlet box to install
the crossbar mounting bracket.
CEILING HARDWARE
WIRE NUT (4)
ADDITIONAL HARDWARE
21/4” x8-32 ROUNDED
HEAD SCREW (2)
FLAT WASHER
(2)
1” x8-32 ROUNDED
HEAD SCREW (2)
SUPPORT INSTALLATION PARTS
LAG SCREW
3/8” #7 X 5” (1)
LARGE
FLAT WASHER
3/8” (1)
WARNING!
SUPPORT DIRECTLY TO
BUILDING STRUCTURE
ONLY.
CROSSBAR
MOUNTING
BRACKET

5
Stealth ®
CANOPY INSTALLATION
Step 4. Attach the canopy to the crossbar mounting bracket with three
of the 8-32 x 21/2” long canopy screws and lock washers provided
with your Casablanca fan. Hand tighten until snug against the ceiling.
CANOPY
SCREW
CANOPY
LOCK
WASHER
FEED OUTLET
BOX WIRES
THROUGH CAN-
OPY OPENING
Note: On sloped ceilings, align the
canopy opening toward the top or
peak of the room.
CANOPY HARDWARE
CANOPY LOCK WASHER
(4)
CANOPY SCREW
(4)
Step 3. With the large washer attached, pass the lag
screw through the center hole of the crosbar mounting
bracket and screw into guide hole. Tighten until outlet

secured to the ceiling. We recommend that the ceiling
   

conditions.
LAG
SCREW
LAG SCREW INSTALLATION
LARGE
WASHER
CANOPY
HATCH CANOPY

6
Step 4. To hang the fan body in the canopy, support the
fan at the center of the glass holder and top support and
insert the ball into the canopy opening. Rotate the fan

canopy opening.
HANGING FAN BODY IN CANOPY
BLADE
HOLDER
BLADE
TIP
BLADE
ATTACHING THE BLADES
BALL
SLOT
PIN
GLASS
HOLDER
INSIDE
TOP SUPPORT
Step 3a. Attach the 5 blade tips to the blades using two
6-32x18” round head screws provided. Note: the screws
have locktite on them, so once they are installed it will

Step 3b.        
 
washers provided for each blade. The truss head screw

pressed on so that it is between the blade and blade
holder; see the detail drawing below. Hand tighten each

CANOPY ELECTRICAL CONNECTORS
WHITE WIRES
(2)
BLACK WIRES
(2)
GREEN WIRES
(3)
WIRE NUT
Step 5.
box wiring by twisting the bare ends of the wires together
and securing with a wire nut. Connect in this order:
        
      
wire nut.
 

 

Note: Write down the
Serial Number and
the model number for
future reference.
3b - BLADE INSTALLATION:
BLADE
BLADE TIP
6-32x1⁄8”
ROUND
HEAD
SCREW
BLADE
BLADE TIP
6-32x1⁄8”
ROUND HEAD
SCREW
3a - BLADE TIP INSTALLATION:
TRUSS HEAD
BLADEHOLDER
SCREW
BLADE
BLADE-
HOLDER
FIBER
WASHER
Note: Fan Weight is 33 lbs.

7
Stealth ®
TILT THE FAN TO
INSTALL LAST
CANOPY SCREW
BULB INSTALLATION
CANOPY HATCH INSTALLATION
CANOPY
CANOPY
LOCK
WASHER CANOPY
SCREW
Step 6. Tuck the wires into the canopy with the wire nuts
pointed upwards, so that the white and black wires are
on opposite sides of the canopy and all wires are clear
of the canopy opening.
Step 7. Install canopy hatch with the last canopy screw
and lock washer. To do this, tilt the fan body away from
the hatch opening.
Step 9.Screw the 100-watt Halogen bulb into the socket.
-
tremely important that the glass be clean. If it is touched,
or dirty, clean carefully with a tissue. A dirty glass bulb
will cause the bulb to fail almost immediately.
INSTALLING THE GLASS
GLASS
HATCH
Step 8. Straighten the fan, then check to ensure that
there is no movement between the canopy and ceiling
or Hang-Tru ball and downrod.
Tip: Place the lock washer on the canopy
screw, and the screw through the hatch before
tilting the fan to install the hatch onto the
canopy.
Step 10. Position the indentations in
the outer rim of the glass so that they
line up with the tabs on the inside sur-

Step 11. Carefully lift the glass shade

will go.
Step 12. Rotate the glass shade in a
clockwise direction until it falls into the
notch for each tab.
Step 13. Turn power back ON at the
circuit breaker or fusebox.
This completes the installation of the
fan.

carefully cut off the end of the plastic sleeve the
bulb comes in and hold the bulb by the plastic
sleeve to screw it into the socket.
NOTE: In compliance with US Federal Energy
Regulations, this ceiling fan contains a device
that restricts the light kit to a maximum of 190
watts. Exceeding that limit or the marked limit
     
improper operation.
INDENTATION
FOR TAB
NOTCH
FOR TAB
MODEL AND
SERIAL NUM-
BER PLATE
GLASS HOLDER
TABS
HALOGEN BULB
100 WATT MAX.

8
®3
WALL CONTROL AND HARDWARE (not to scale)

Screws (2)
Wall Plate
Screws
(2) White
(2) Almond
White Wall
Plate(1)
W-85
Wall Control
Switch Bezels
(1) White
(1) Almond
Almond Wall
Plate(1)
(4) Wire Cap
Before installing the W-85 wall control you will need to
check and see if you will need to change the bezel on

If you are going to use white, skip these steps and go
to wall control installation starting on page 10. The
bezel can be changed at any time before or after
installation. The wall control does not need to be
uninstalled to replace the bezel.
W-85 Wall Control Bezel Replacement installation
as follows
Step 17a. Locate the four (4) tabs holding the bezel to
the front of the switch, then press in on each tab one
at a time, removing the bezel as shown in Figure #1.
Step 17b. Locate the rubber key pad attached to
the four (4) locating pins as shown in Figure #2 and
remove rubber key pad from the WHITE bezel, also
as shown in Figure #2.
WARNING!
To avoid possible electrical shock, make cer-
tain that electricity is turned off at the circuit
breaker or fuse box before attempting any in-
stallation or repair procedure
CAUTION! NOT turning the power OFF at the
circuit breaker or fuse box may cause damage to
the electronics within the wall control and or the PC
board on the fan.
Figure #2
WHITE
BEZEL
RUBBER KEY
PAD

PINS (4)

PINS
HOLES(4)
W-85 CONTROL INSTALLATION
Figure #1
BEZEL
BEZEL
TABS

9
®3
Figure #5

BEZEL
BEZEL
TABS
BEZEL

PIN AND HOLE
Figure #3

BEZEL
RUBBER KEY
PAD
W-85 Wall Control Bezel replacement: -
CONTINUED
Step 17c. Reinstall the rubber key pad on to the
four (4) locating pins located on the almond bezel
as shown in Figure #3 and #4.
Step 17d. To attach the bezel back on to the front
of the switch you will need to align the four (4) tabs
on the bezel with the front of the wall control and
by gently pressing on both top and button of the
bezel at the same time, snap the bezel back on to

Step 17e. Check your work by pressing on the
light, fan, reverse and power buttons, making sure
that the buttons do not stick and that each switch
functions properly.
RUBBER KEY
PAD

BEZEL
Figure #4

PINS
(4)

10
®3
INSTALLING THE W-85 WALL CONTROL
1. Use only the Casablanca W-85 wall control.
2. Do not use any additional control with your Inteli-Touch
3 fan (for example, dimmer, or fan speed control).
3. Do not use more than one fan per wall control.
4. No other light xtures or electrical appliances may be
connected on the circuit controlled by the W-85 wall
control.

If you have multiple Inteli-Touch 3 fans, refer to the section
"Changing Frequency Setting" on page 13.
1. Remove the screws and switch plate from the existing switch
box.
2. Remove the screws holding the switch in the switch box.
3. Pull the existing switch from the switch box to expose the
wire connections.
4. Remove the two wires from the switch.
5. Connect the BLACK wire from the POWER SOURCE that
you just removed from the switch to the BLACK/WHITE
STRIP wire on the W-85 wall control.Secure this connection
with a wire nut.
The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this
reason the following precautions must be observed:
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
NOTE: The RED wire is not used in this
application, DO NOT remove the crimped cap
from the wire..
BLACK AND WHITE
STRIPED WIRE
W-85
Wall Control
2 BLACK
WIRES
RED WIRE
NOT USED
(FIGURE #2)
(FIGURE #1)
NOTE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch®3 fans with DOWNLIGHTS ONLY.
6. Connect the second BLACK wire that you just
removed from the switch to the second BLACK
wire on the located on the back of the W-85 wall
control. Secure this connection with a wire nut.
7. Connect the green ground wire coming from the
back of the W-85 control to the ground wire in
the switch box. Secure the splice with a wire nut.
8. Check your work by using the wiring diagrams
as shown in Figures # 1 and #2.
9. Install the W-85 in the wall box with the two
long screws provided.
10.Install the wall plate with the two color-matched
screws.
SINGLE W-85 INSTALLATION
W-85

11
®3
DUAL W-85 INSTALLATION
To control the fan and lights from two locations (a three-way circuit), use two W-85
wall controls as shown in the wiring diagram in Figure #5. Before installing the
two switches into the wall, place both switches side by side, then locate the 4 dip
switches on the side of the two switches. Then make sure that the dip switches
are set to the same address on both switches as shown in Figure #4. When setting
these dip switches you are setting the channel number that is required to control
both your fan and lights from both sides of the room. If you are installing other
Inteli-Touch®3 fans within your home you may need to reset the dip switches on
these other fans to a different channel before installing your W-85 wall control into
the wall. Please review the section on channel changing on this instruction sheet.
DIP SWITCHES
(FIGURE #4)
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting
installation.
Tocontrolthefanandlightsfromtwolocations(athree-waycircuit),usetwo
W-85 wall controls.
1. Remove the screws and switch plate from the existing switch box and the
screws holding the switch in the switch box.
2. Pull the existing switch from the switch box to expose the wire connections.
3. Determine which wire is connected to the common terminal from the
power source (120V AC) of the three-way switch. (e terminal will be
marked on switch).
4. Remove the wire from the common terminal of the three-way switch. Connect
this wire to the remaining black/white striped wire on the W-85 control. Secure
this splice with a wire nut.
5. Remove the two remaining wires from the three-way switch. Connect the black
wire of these wires to a black wire on the W-85 control. Secure the splice with a
wire nut. e remaining red wire is to be connected to the other red wire on the
W-85. Secure the splice with a wire nut.
6. Connect the green ground wire coming from the back of the W-85 control to the
ground wire in the switch box. Secure the splice with a wire nut.
7. Check your work by using the wiring diagrams as shown in Figure #5 on this page.
8. Install the W-85 in the wall box with the two long screws provided.
9.Install the wall plate with the two short color-matched screws provided.
10.Installation of the second W-85 control is identical. Repeat steps 1 through 9.
W-85
Wall Control
BLACK AND WHITE
STRIPED WIRE
2 RED WIRES
2 BLACK
WIRES
(FIGURE #5)
W-84
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
RED
GREEN
120V AC
BLACK
BLACK WITH
WHITE STRIPE
W-84
RED RED
RED
BLACK WITH
WHITE STRIPE
GREEN
NEUTRAL
WHITE
GREEN
W-85 W-85

12
®3
OPERATION POWER
The button is normally left in the on position. Always turn the power off
during cleaning or servicing the fan and during thunderstorms. It is also used to
exit or enter additional programs.
The button must be left on to retain a previously set fan speed or light level.
OPERATION SPEED CONTROL
FAN CONTROL
ON - OFF:
A momentary
press of the FAN
button

Press and hold
FAN button longer
than one second
There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled . The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the
same speed each time the button is used. To maintain this level
of speed, turn the fan on by pressing less than one second. To
lower speed, turn fan off, then on by pressing and holding the
button until the desired speed is reached. When the fan is on, you may
increase the speed by pressing and holding the button until the
desired speed is reached, then release it.
OPERATION REVERSING AIRFLOW
-
ward to upward or from upward to downward.

 is on and blades are Turn-
ing.
2. Press the button.
Note: A four-toned signal
indicates the command was
accepted by the fan. A few
seconds later the fan will slow
to a stop and then reverse
direction.

ON - OFF:
A momentary press of
the LIGHT button
-
NESS:
PRESS AND HOLD


SECOND
To turn the lights off and on, press and release the button for less than
one second.
1) First press/release of the button- The light will turn ON.
2) Second press/release of the button- The light will turn OFF.
To vary the light brightness at each touch level:
To vary the light brightness:
1. With lights off, press and hold the button. After one second the lights will
come on at their lowest level and gradually become brighter.
OPERATION LIGHTS
NOTE: Light Operation - the light varies from “bright” to “dim” over
approximately 8 seconds. This sequence will reverse the light when it reaches
            
Release the button when the desired level is reached.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come on at
the same brightness the next time the button is used.

13
®3
CHANGING FREQUENCY SETTING
NOTE: All fans leave the factory set to
“1111”
You will only have to change the dip switch settings in the remote if you are using
more than one fan in the same area and want to control them separately.
Step 1. Turn power OFF at the circuit breaker or fuse box and at the toggle switch,
for the fan you want to change.
DIP
SWITCHES
DIP SWITCHES
SET TO ‘1111’
(Factory Setting)
DIP SWITCHES
SET TO ‘1001’
AUTOMATIC DEMONSTRATION PROGRAM
A multi-tone signal will verify the start of the test pro-
gram which proceeds as follows:
 
 
 
 
 
 
 
short time).
 
The complete cycle lasts slightly over one minute. It
will continue to repeat until the is turned off

Programmed into every Inteli-Touch®3 Series fan is
an Automatic Demonstration Program. It can be used
to fully demonstrate and test the operation of the fan.
To enter the demonstration program:
1. Turn off for at least 5 seconds. This will
clear the fan memory ready for programming.
2. Turn on.
3. Immediately operate the buttons in the following
sequence:
+++ +
NOTE: DO NOT set dip switch setting in the remote
to ‘0000’, this may cause frequency interference from
other Casablanca Products.
Step 2. Remove the screws and switch plate from the existing switch box.
Step 3. Remove the screws holding the switch in the switch box.
Step 4. Pull the existing W-85 switch from the switch box to expose the dip switches
located on the side of the control as shown in Figure #1.
Step 5. Change the dip switch settings, assuring that they are different from the
previously installed Inteli-Touch®3 fan.

Step 7. At the circuit breaker or fuse box and at the toggle switch, turn the power off
for the fan whose frequency you are changing.
Step 8. Within 20 seconds of restoring power to the ceiling fan and the W-85 Wall
Control press and hold both the “FAN” and “REVERSE” buttons as shown in Figure
#2 for 3 seconds, you will hear one tone from the Piezo Buzzer indicating the com-
mand has been accepted.

14
®3
OPERATION HOME-SAFE®PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
 But-
ton off for a least 5 seconds.
2) Turn the on. Immediately press the buttons in the following sequence:
+ + + . A series of tones will be heard through the

follow. This program overrides all manual control of lights and fan. Once the lights
turn on, they will automatically turn off after 2 hours.
3) The lights will automatically cycle on and off in a controlled sequence as follows:
ON 1 hour, OFF ½ hour, ON 2 hours, OFF 1 hour, ON ½ hour then OFF 2 hours.
This seven hour pattern will repeat continuously so that a different pattern of lighting
is seen each day of the week.
4) To cancel the Home-Safe Program, press the     
seconds.
OPERATION SAFE-EXIT®AND LIGHT-MINDER®PROGRAM
NOTE:

hours.
To enter the Light-Minder Program:
 button off for at
least 5 seconds.
2) Turn the on. Immediately press the buttons in the following sequence:
+ + + . A series of tones will be heard through the piezo-
buzzer indicating the command has been accepted. Once the lights turn on, they will
automatically turn off after 2 hours.
3) Light operation still remains normal, if you leave the room and turn OFF the lights
will blink to indicate this Safe-Exit command has been accepted. The lights will stay
on for 30 seconds and then begin to dim. After thirty seconds have elapsed, the lights
will turn completely off.
 button.
The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off,
enabling you to exit your home before the lights go out. To enter the Safe-Exit Program:
 button off for at

2) Turn the Power on. Immediately press the buttons in the following sequence:
+ + + . Immediately press the Button after an audio tone
is heard from the fan controller. The lights will blink to indicate this command has been
accepted. The lights will stay on for 30 seconds and then begin to dim. After thirty
seconds have elapsed, the lights will turn completely off.
3) To cancel the Safe-Exit Program, press the 
NOTE: If the lights are left on in the room, the lights will automatically turn


Safe-Exit

15
®3
OPERATION FAN-MINDER™PROGRAM

reduces the speed of the fan each two-hour interval to compensate for cooling night air.

1. Turn the OFF for at least 5 seconds.
2. Turn the ON.
3. Immediately operate the buttons in the following sequence:
+++
4. The fan will respond with three descending tones. A timer is now initiated and the fan will
reduce one speed for each two-hour interval. The fan will not, however, descend below
the second lowest speed.
5. You may increase the fan speed by pressing and holding the button until the
desired speed is reached, then release it. The fan will again reduce one speed for each
2 hour interval.
 OFF for three seconds.

16
®3
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
TROUBLESHOOTING TIPS
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving antenna, Increase the separation
between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver

transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote
control.
 
  

inspection.
  
  
  
for the fan that is not functioning only. Within 20 seconds from restoring
power to the ceiling fan and the W-85 Wall Control press and hold both
the “Fan” and “REVERSE” buttons as shown in Figure #2 for 3 seconds,
you will hear one tone from the Piezo Buzzer indicating the command
has been accepted. The Fan will come on at “low” speed in the reverse
direction.
  
  
the blades are balanced.
       


  
the screws are securely tightened.
  
normal operation.
  
and/or lightbulb(s).
           
the wire nuts inside the canopy and switch housing are not touching the
metal parts and that they have not fallen off the wire splices. Tighten as
necessary.
  
blades to the bladeholder screws.
  
tight.
  
days.

17
Stealth ®
PRODUCT SPECIFICATIONS
 ®
 
Dimensions: A = 10.8"
B = 13.25"
C = 3"
D = 11.5"
E = 5.6"
Weight: 33 lbs.
  ®
Blade Span: 54"
Blade Iron Pitch: 14°
No. of Blades: 5
  ®3 W-85
Lightbulb: (1) 100-watt halogen
lightbulb
  
Electricity Use*: 112 watts
  
* Performance data is for fan only. No lighting wattage is included.
NOTE: Dimension B
includes light xture
and glass.