cascade corporation A Series User manual

Manual Number 1849482-R2
Cascade is a Registered Trademark of Cascade Corporation
cascade
corporation
SER MANUAL
A-Series
Fork Positioner/
Sideshifter
U

1849482-R2
i
ONTENTS
C
Page
INTRODUCTION
Special Definitions 1
OPERATION
Safety Rules 2
Industrial Lift Trucks 2
Handling Loads 3
Sideshifter Operation 3
Safe Operation and Maintenance 4
TRUCK REQUIREMENTS 5
HYDRAULIC SUPPLY 6
INSTALLATION 7
PERIODIC MAINTENANCE
Daily 13
100-Hour Maintenance 13
300-Hour Maintenance 13
1000-Hour Maintenance 13
2000-Hour Maintenance 14
PARTS
Recommended Spare Parts 15
Publications 15
NTRODUCTION
I
This user manual is for the Cascade A-Series Fork
Positioner/Sideshifter. Contents include an Operator's
Guide, Installation Instructions, Periodic Maintenance and
Parts Manual.
NOTE: All specifications are shown in U.S. and (Metric)
units where applicable. All fasteners have a torque value
range of ±10% of stated value.
IMPORTANT: A-Series Fork Positioner/Sideshifter is
metric. Supply fittings adapted as required for application.
Sideshifter stamped model
number, serial number,
customer part number
Sticker showing patent
numbers, phone
numbers for service
Stamped capacity,
weight, horizontal CG
Fork positioner nameplate with stamped
model number, serial number, part
number and specifications
FP0609.ill

1849482-R21
PERATION
This Section contains operating instructions for the
Cascade A-Series Fork Positioner/Sideshifter. It will help
you avoid common errors which often cause damage to
the equipment or product being handled.
This information is intended to simplify operator
understanding about effective and safe Fork Positioner/
Sideshifter use and operation. Read this information
thoroughly before operating the attachment. Be sure
you know and understand all operating procedures and
safety precautions. If you have any questions, or don’t
understand a procedure, ask your supervisor.
Emphasise Safety! Most accidents are caused by
operator carelessness or misjudgement. You must
watch for poorly maintained equipment and
hazardous situations and correct them.
NTRODUCTION
I
WARNING: Rated capacity of the truck/
attachment combination is a responsibility
of the original truck manufacturer and may
be less than shown on the attachment
nameplate. Consult the truck nameplate.
WARNING: Do not operate this attachment
unless you are a trained and authorised lift
truck driver.
CAUTION – A statement preceded by CAUTION is
information that should be acted upon to prevent
machine damage.
IMPORTANT – A statement preceded by IMPORTANT is
information that possesses special significance.
NOTE – A statement preceded by NOTE is information that
is handy to know and may make the job easier.
Special Definitions
The statements shown appear throughout this Manual
where special emphasis is required. Read all WARNINGS
and CAUTIONS before proceeding with any work.
Statements labeled IMPORTANT and NOTE are provided
as additional information of special significance or to make
the job easier.
WARNING – A statement preceded by
WARNING is information that should be
acted upon to prevent bodily injury. A
WARNING is always inside a ruled box.
O
FP0156.ill
Fork Carriers
Cylinders / Bearing Ways
Frame / Backrest
Valve
Sideshifter
Frame / Backrest

1849482-R2
2
GA0048.eps
PERATION
OSafety Rules – Industrial Lift Trucks
No standing under load
No reaching through mastNo riders
GA0047.eps
Motor off, park, lower load
With load
Tilt
Raise
No load
Traveling
empty
3 in.
(8 cm)
P P
TRAFFIC
No parking on ramp Watch clearances No turning on ramp
P
STOP
RAMPS
Slow for
two-way traffic
Sound horn, slow
at intersection
Wet floors Bumps Dips
Workers Stops
Sound horn, slow
at corner
Observe

1849482-R23
PERATION
OSafety Rules – Handling Loads
FP0174.eps
Limit truck movement
with raised load.
Top of load
should not extend
above backrest.
Load weight must not exceed
combined truck/attachment
capacity (see truck nameplate).
Total fork capacity (LH + RH fork)
must be greater than load weight.
Check capacity stamp on forks.
CAUTION: Do not put
side loads on forks.
Center load
prior to
traveling.
Limit sideshifting
with raised load.
LOAD
WEIGHT
BD
C
A
GA0005.eps
Hoist down Tilt forward
Hoist up Tilt Back
AUXILIARY VALVE
FUNCTIONS
Fork Positioner/Sideshifter Operation
Raise load prior
to sideshifting.
WARNING: Truck control handle and attachment
function activation shown here conforms to
ASME/ANSI B56.1 recommended practices.
Failure to follow these practices may lead to
serious bodily injury or property damage. End
user, dealer and OEMs should review any
deviation from the practices for safe operation.
SIDESHIFTING WITH
SOLENOID VALVE
ASideshift Left
ASpread Forks
(press knob button)
BSideshift Right
BClose Forks
(press knob button)
NON-SIDESHIFTING
ASpread Forks
BClose Forks
C (not used)
D (not used)
FP0164.ill
A
B
A
B
FP0164.ill
BA
C
C
D
D
FP0164.ill
A
B
A
A
B
B
SIDESHIFTING
ASideshift Left
BSideshift Right
CSpread Forks
DClose Forks

1849482-R2
4
AFE OPERATION AND MAINTENANCE
OSHA Regulations – Industrial Trucks and Attachments (Specific Regulations from OSHA 1910.178)
WARNING: The safe operation and maintenance of
industrial trucks is regulated by Occupational Safety
and Health (OSHA) regulations 1910.178 and Ameri-
can National Standards Institute (ANSI) Safety Stan-
(a) General Requirement
(4) Modifications and additions which affect capacity and safe
operation shall not be performed by the customer or user without
manufacturers prior written approval. Capacity, operation and
maintenance instruction plates, tags or decals shall be changed
accordingly.
(5) If the truck is equipped with front-end attachments other than
factory installed attachments, the user shall request that the truck
be marked to identify the attachments and show the appropri-
ate weight of the truck and attachment combination at maximum
elevation with load laterally centered.
(6) The user shall see that all nameplates and markings are in place
and maintained in a legible condition.
(e) Safety Guards
(2) If the type of load presents a hazard, the user shall equip fork
trucks with a vertical load backrest extension in accordance with
(a)(2) following.
(a)(2) All new powered industrial trucks acquired and used by
an employer after February 15, 1972 shall meet the design and
construction requirements for powered industrial trucks estab-
lished in the “American National Standard for Powered Industrial
Trucks, Part II, ANSI B56.1”, except for vehicles intended primarily
for earth moving or over-the-road hauling.
(l) Operator Training
Only trained and authorized operators shall be permitted to operate a
powered industrial truck. Methods shall be devised to train operators
in the safe operation of powered industrial trucks.
(m) Truck Operations
(1) Trucks shall not be driven up to anyone standing in front of a
bench or other fixed object.
(2) No person shall be allowed to stand or pass under the elevated
portion of any truck, whether loaded or empty.
(3) Unauthorized personnel shall not be permitted to ride on powered
industrial trucks. A safe place to ride shall be provided where rid-
ing of trucks is authorized.
(4) The employer shall prohibit arms or legs from being placed be-
tween the uprights of the mast or outside the running lines of the
truck.
(5i) When a powered industrial truck is left unattended, load engaging
means shall be fully lowered, controls shall be neutralized, power
shall be shut off and brakes set. Wheels shall be blocked if the
truck is parked on an incline.
(5ii) A powered industrial truck is unattended when the operator is 25
feet or more away from the vehicle which remains in his view, or
whenever the operator leaves the vehicle and it is not in his view.
(5iii) When the operator of an industrial truck is dismounted and within
25 feet of the truck still in his view, the load engaging means
shall be fully lowered, controls neutralized and the brakes set to
prevent movement.
S
(6) A safe distance shall be maintained from the edge of ramps or
platforms while on any elevated dock or platform or freight car.
Trucks shall not be used for opening or closing freight doors.
(10) A load backrest extension shall be used whenever necessary
to minimize the possibility of the load or part of it from falling
rearward.
(n) Traveling
(4) The driver shall be required to slow down and sound the horn
at cross isles and other locations where vision is obstructed. If
the load being carried obstructs forward view, the driver shall be
required to travel with the load trailing.
(7i) When ascending or descending grades in excess of 10 percent,
loaded trucks shall be driven with the load upgrade.
(7iii) On all grades the load and load engaging means shall be tilted
back if applicable, and raised only as far as necessary to clear
the road surface.
(o) Loading
(1) Only stable or safely arranged loads shall be handled. Caution
shall be exercised when handling off-center loads which cannot
be centered.
(2) Only loads within the rated capacity of the truck shall be handled.
(3) The long or high (including multiple-tiered) loads which may
affect capacity shall be adjusted.
(4) Trucks equipped with attachments shall be operated as partially
loaded trucks when not handling a load.
(5) A load engaging means shall be placed under the load as far as
possible; the mast shall be carefully tilted backward to stabilize
the load.
(6) Extreme care shall be used when tilting the load forward or
backward, particularly when high tiering. Tilting forward with load
engaging means elevated shall be prohibited except to pick up
a load. An elevated load shall not be tilted forward except when
the load is in a deposit position over a rack or stack. When stack-
ing or tiering, only enough backward tilt to stabilize the load shall
be used.
(p) Operation of the Truck
(1) If at any time a powered industrial truck is found to be in need of
repair, defective, or in any way unsafe, the truck shall be taken
out of service until it has been restored to safe operating condi-
tion.
(q) Maintenance of Industrial Trucks
(1) Any power-operated industrial truck not in safe operating
condition shall be removed from service. All repairs shall be
made by authorized personnel.
(5) All parts of any such industrial truck requiring replacement shall
be replaced only by parts equivalent as to safety with those used
in the original design.
(6) Industrial trucks shall not be altered so that the relative positions
of the various parts are different from what they were when origi-
nally received from the manufacturer, nor shall they be altered
either by the addition of extra parts not provided by the manufac-
turer or by the elimination of any parts. Additional counter-weight-
ing of fork trucks shall not be done unless approved by
the truck manufacturer.
(7) Industrial trucks shall be examined before being placed in ser-
vice and shall not be placed in service if the examination shows
any condition adversely affecting the safety of the vehicle. Such
examinations shall be made at least daily. When industrial trucks
are used on a round-the-clock basis, they shall be examined after
each shift. Defects when found shall be immediately reported
and corrected.
dard for Powered Industrial Trucks, ANSI B56.1. When operating
and maintaining industrial trucks equipped with attachments you
should pay particular attention to the following sections of these
regulations. You should be familiar with all sections of these
regulations. Ask your employer for the complete regulations.

1849482-R25
TRUCK REQUIREMENTS
GA0131.eps
Auxiliary Valve Functions
Check for compliance with
ANSI (ISO) standards:
A
GA0028.eps
Carriage Mount Dimension (A) ITA (ISO)
Minimum Maximum
Class II 14.94 in. (380.0 mm) 15.00 in. (381.0 mm)
Class III 18.68 in. (474.5 mm) 18.74 in. (476.0 mm)
Class IV 23.44 in. (595.5 mm) 23.50 in. (597.0 mm)
GA0082.eps
Sideshift
Left
Hoist Up
Tilt
Back
Tilt
Forward
Sideshift
Right
Hoist Down
Carriage – Clean and inspect carriage
bars. Make sure that bars are parallel and that
ends are flush. Grind smooth any protruding
welds that may affect Sideshifter lower
bearings. Repair any damaged notches.
Open
Forks
Close
Forks
Truck Relief Setting
2300 psi (160 bar) Recommended
2600 psi (180 bar) Maximum
Truck Flow Volume ➀
Min. ➁Recommended Max. ➂
Fork Position 3GPM
(11 L/min.)
4GPM
(15 L/min.)
5GPM
(19L/min.)
Sideshift 1 GPM
(4 L/min.)
2GPM
(7.5L/min.)
3GPM
(12 L/min.)
➀Cascade A-Series Fork Positioner/Sideshifters are compatible with
SAE 10W petroleum base hydraulic fluid meeting Mil. Spec. MIL-0-
5606 or MIL-0-2104B. Use of synthetic or aqueous base hydraulic
fluid is not recommended. If fire resistant hydraulic fluid is required,
special seals must be used. Contact Cascade.
➁Flow less than recommended will result in slow fork positioning speed.
➂ Flow greater than maximum can result in excessive heating, reduced
system performance and short hydraulic system life.

1849482-R2
6
HYDRAULIC SUPPLY
GA0365.eps
A
Fork Positioning function: No. 3 hose/No. 4 fittings with
5/32-in (4 mm) minimum I.D.
Sideshifting function: No. 4 hose/No. 6 fittings with
3/16-in. (5 mm) minimum I.D.
Refer to Cascade Hose & Cable Reel Selection Guide, Part
No. 212199 to select the correct hose reel for the mast and
truck.
Fork Positioning / Sideshifting
A Mast Double Internal Reeving
Solenoid Adaption
A Mast Single Internal Reeving
with RF Hydraulic Control

1849482-R27
NSTALLATION
Install bolt-on lower hooks
4
3
Attach overhead hoist
I
FP0724.eps
FP0794.eps
Truck Upper
Carriage Bar
Engage locator tab
on sideshifter with
center notch
Sideshifter
Truck Lower
Carriage Bar
ITA Class II – .60-.66 in. (15-17 mm)
ITA Class III – .72-.78 in. (18-20 mm)
ITA Class IV – .72-.78 in. (18-20 mm)
ITA Class II – .32–.36 in. (8-9 mm)
ITA Class III – .39–.43 in. (10-11 mm)
ITA Class IV – .47–.51 in. (12-13 mm)
Tighten bolts to:
Class II/III – 120 ft.-lbs. (165 Nm)
Class IV – 235 ft.-lbs. (320 Nm)
Clearance:
1/32 in. (0.8 mm) Min.
1/16 in. (1.6 mm) Max.
Mount unit on truck carriage
Remove bolt-on lower hooks
1
2
FP1214.eps
WARNING: Check the attachment weight
(located on the nameplate) to make sure the
overhead hoist and chains or straps are at
least the rated capacity of the attachment.
FP0601.ill

1849482-R2
8
INSTALLATION
Install hoses
5
6
Flush supply hoses
CAUTION: Allow for 4 inches movement in
each direction for sideshifting ('rolling' hose
arrangement recommended).
Back (Driver's) View
AConnect supply hoses to supply
terminals and connect together using
a union fitting as shown.
BOperate auxiliary valve for 30 sec.
CRemove union fitting
FP1432.eps
FP1115.eps
7Remove fork locking pins
WARNING: Remove locking pins
from forks. Make sure that forks
slide freely on carriage bars.
Remove Fork
Pin Assembly
GA0092.ill
FP0602.ill
Close Forks Spread Forks
Sideshift Right Sideshift Left

1849482-R29
8Install Forks
ADisconnect cylinder rod-end anchors from
fork carriers and retract cylinder rods.
BRotate fork carriers up to provide clearance
for fork installation.
CInstall forks using bottom fork slot to
engage forks with sideshifter carriage.
DLine up forks with fork carriers on frame and
rotate fork carriers down into position over
forks. Assure fork spacer plates are in
place if required.
EReconnect cylinder rod anchors using two
hardened washers and self-locking nut (see
illustration below). Adjust nut to provide
1/32 in. (1 mm) clearance in joint. Use flats
on cylinder rod end to prevent turning.
IMPORTANT: Joint must function with a
loose operating clearance. Lubricate with
chassis grease.
WARNING: Remove locking pins
from forks. Assure that forks slide
freely on sideshifter carriage bars.
NSTALLATION
I
FP0608.ill
FP0603.ill
Hardened Washers (2)
E
Fork Positioner Frame
Fork Carrier
D
Sideshifter
Assembly
Forks
Self-Locking Nut
Wrench Flat
B
C
Backrest
Cylinder Rod End
FP0610.ill
Fork Spacer Plate
(if required) D
1/32 in. (1 mm)

1849482-R2
10
INSTALLATION
10
Lubrication
Fork Positioner/Sideshifter is prelubed at
the Factory and requires no lubrication
for installation. Use graphite dry lube for
fork bars as required ('Slip Plate Aerosol',
'GraphoKote' or equivalent).
After use, lubricate fork positioner and
sideshifter as described in Periodic
Maintenance Section in this Manual.
Cycle Fork Positioner functions
11
• Openandcloseforksseveraltimes.
Sideshift (if equipped) left and right.
Check for smoothness and equal
movement.
• Checkforoperationinaccordancewith
ANSI (ISO) standards.
• Checkforleaksatttings,valve,
cylinders.
• Checkthatrollinghosessupplyingfork
position are not pinched.
BD
C
A
GA0005.eps
Hoist down Tilt forward
AUXILIARY VALVE
FUNCTIONS
WARNING: Truck control handle and attachment
function activation shown here conforms to
ASME/ANSI B56.1 recommended practices.
Failure to follow these practices may lead to
serious bodily injury or property damage. End
user, dealer and OEMs should review any
deviation from the practices for safe operation.
Tilt back
Hoist up
SIDESHIFTING WITH
SOLENOID VALVE
ASideshift Left
ASpread Forks
(press knob button)
BSideshift Right
BClose Forks
(press knob button)
NON-SIDESHIFTING
ASpread Forks
BClose Forks
C (not used)
D (not used)
FP0164.ill
A
B
A
B
FP0164.ill
BA
C
C
D
D
FP0164.ill
A
B
A
A
B
B
SIDESHIFTING
ASideshift Left
BSideshift Right
CSpread Forks
DClose Forks

1849482-R211
INSTALLATION
12
Back (Driver's) View
13Inspect fork hooks,
carriage bar clearance
NOTE: Use go/no-go Wear Gauge Part No. 209560
(Class II), 209561 (Class III) or 6104118 (Class IV).
AInspect the fork lower hooks and carriage bar.
If the gauge fits between the carriage bar and
lower hook, repair or replacement is needed.
B Inspect the upper carriage bar. If the gauge
arrow touches the carriage bar, repair or
replacement is needed.
CInspect the fork upper hooks. If the gauge
arrow touches the hook, repair or replacement
is needed.
Adjust forks for equal movement
(if required)
NOTE: Attachment is Factory-adjusted for equal
fork movement when operated at recommended
pressure and flow rate.
ALocate flow restrictors on right hand cylinder
(only one (1) flow restrictor used).
B Open forks fully, then close. Look for unequal
fork movement.
CLoosen restrictor jam nut and adjust untill
right hand fork moves equally with left hand
fork. Tighten jam nut.
FP0832.eps
OK
OK
OK
FORK LOWER HOOKS, CARRIAGE
UPPER CARRIAGE BAR
FORK UPPER HOOKS
Wear
Gauge
FP0625.ill
Flow
Restrictor
Fitting
A

1849482-R2
12
FP0606.ill
Front View
Back (Driver's) View
Frame and Backrest Mounting Capscrews (4)
Cylinder Rod
Anchors (2)
Fork Carrier
Bearings (2)
Sideshifter
Lower Bearings (2)
Lower Mounting Hook
Capscrews (4)
FP0607.ill
Sideshifter
Grease Fittings (2)
PERIODIC MAINTENANCE
100-Hour Maintenance
Every time the lift truck is serviced or every 100 hours of
truck operation, whichever comes first, perform the
following maintenance procedures:
•Check for loose or missing bolts, worn or damaged
hoses and hydraulic leaks.
500-Hour Maintenance
After each 500 hours of truck operation, in addition to the
100-hour maintenance, perform the following procedures:
•Tighten frame and backrest mounting capscrews to
115-125 ft.-lbs. (155-170 Nm).
•Tighten lower hook capscrews:
Class II / III – 120 ft.-lbs. (165 Nm).
Class IV – 235 ft.-lbs. (320 Nm).
•Apply graphite dry lube to fork carrier bearings ('Slip
Plate', 'GraphoKote' or equivalent).
•Apply chassis grease to fork cylinder rod anchors.
•Apply chassis grease to sideshifter upper bearing
grease fittings, and lower flat bearings.
•Check fork hooks and carriage bars for wear using a
wear gauge (Cascade Part No. 209509 for Class II,
209507 for Class III and 6104118 for Class IV).
1000-Hour Maintenance
After each 1000 hours of truck operation, in addition to
the 100 and 500-hour maintenance, perform the following
procedures:
•Inspect fork carrier bearings for wear and replace if
necessary.
•Inspect fork cylinder rod anchor washers for wear and
replace if necessary.
•Inspect thickness of sideshifter (if equipped) upper
and lower bearing sets. If any bearing in the set is
worn to less than 3/32 in. (2.5 mm) thickness, replace
entire bearing set (see Service Manual).
WARNING: After completing any service
procedure, always test each function
through five complete cycles. First test
with no load, then test with a load to
make sure the attachment operates
correctly before returning it to the job.

1849482-R213
PERIODIC MAINTENANCE
After 2000 hours of truck operation, in addition to the
100, 300 and 1000-hour maintenance, forks in use shall
be inspected at intervals of not more than 12 months
(for single shift operations) or whenever any defect or
permanent deformation is detected. Severe applications
will require more frequent inspection.
Fork inspection shall be carried out by trained personnel
to detect any damage that might impair safe use. Any fork
that is defective shall be removed from service. Reference
ANSI B56.1-2005.
Inspect for the following defects:
•Surface cracks
•Straightness of blade and shank
•Fork angle
•Difference in height of fork tips
•Positioning lock
•Wear on fork blade and shank
•Wear on fork hooks
•Legibility of marking
NOTE: Fork Safety Kit 3014162 contains wear calipers,
inspection sheets and safety poster. Also available
is fork hook & carriage wear gauge 209560 (Class II),
209561 (Class III) and 6104118 (Class IV).
2000-Hour

1849482-R2
14
Recommended Spare Parts
■Refer to part number stamped on part or supply serial number stamped on sideshifter frame
when purchasing these parts.
FORK POSITIONER / SIDESHIFTER UNITS SERVICED
55A
PART NO.
65A
PART NO.
100A
PART NO.
120A, 150A,
165A
PART NO. DESCRIPTION
1-5 6-19 20-50
QTY. QTY. QTY.
FORK POSITIONER
111173 111173 111173 111173 Cylinder Service Kit 0 4 6
SIDESHIFTER
228782 6051249 6051249 6079936 Upper Bearing–Composite 8 16 32
6000616 6052405 6052405 6082297 Upper Bearing–Bronze 4 8 16
6000719 6057162 6057162 6057162 Lower Bearing–Composite 6 12 24
225570 6058041 6058041 6058041 Lower Bearing–Bronze 4 8 16
204186 204186 204186 6083157 Lower Hook 0 2 4
752903 752903 752903 — Capscrew, M16 x 45 0 4 8
— — — 768580 Capscrew, M20 x 60 0 4 8
678990 678990 678990 — Nut, M16 0 4 8
— — — 783800 Nut, M20 0 4 8
667225 667225 667225 215419 Washer 0 4 8
■ ■ ■ ■Cylinder Assembly 0 0 1
219868 219868 564409 564409 Cylinder Service Kit 1 2 4
PARTS
6107750 6107750 6107750 6107750 Bearing, Fork Eye –Bronze 4 8 16
111153 111153 111153 111153 Cylinder, Gland Nut 0 2 4

1849482-R215
PAGE INTENTIONALLY LEFT BLANK

c
© Cascade Corporation 201208-2016 Part Number 1849482-R2
Do you have questions you need
answered right now? Call your
nearest Cascade Parts Department.
Visit us online at www.cascorp.com
AMERICAS
Cascade Corporation
Parts Sales
2501 Sheridan Ave.
Springfield, OH 45505
Tel: 888-CASCADE (227-2233)
Fax: [phone]
Cascade Canada Inc.
5570 Timberlea Blvd.
Mississauga, Ontario
Canada L4W-4M6
Tel: [phone]
Fax: [phone]
Cascade do Brasil
Rua João Guerra, 134
Macuco, Santos - SP
Brasil 11015-130
Tel: [phone]
Fax: [phone]
EUROPE-AFRICA
Cascade Italia S.R.L.
European Headquarters
Via Dell’Artigianato 1
37050 Vago di Lavagno (VR)
Italy
Tel: [phone]
Fax: [phone]
Cascade (Africa) Pty. Ltd.
PO Box 625, Isando 1600
60A Steel Road
Sparton, Kempton Park
South Africa
Tel: [phone]
Fax: [phone]
ASIA-PACIFIC
Cascade Japan Ltd.
2-23, 2-Chome,
Kukuchi Nishimachi
Amagasaki, Hyogo
Japan, 661-0978
Tel: [phone]
Fax: [phone]
Cascade Korea
121B 9L Namdong Ind.
Complex, 691-8 Gojan-Dong
Namdong-Ku
Inchon, Korea
Tel: [phone]
Fax: [phone]
Cascade-Xiamen
No. 668 Yangguang Rd.
Xinyang Industrial Zone
Haicang, Xiamen City
Fujian Province
P.R. China 361026
Tel: [phone]
Fax: [phone]
Cascade India Material
Handling Private Limited
No 34, Global Trade Centre
1/1 Rambaugh Colony
Lal Bahadur Shastri Road,
Navi Peth, Pune 411 030
(Maharashtra) India
Phone: [phone]
Fax: [phone]
Cascade Australia Pty. Ltd.
36 Kiln Road
Darra, QLD 4076
Australia
Tel: [phone]
Fax: [phone]
Cascade New Zealand
15 Ra Ora Drive
East Tamaki, Auckland
New Zealand
Tel: [phone]
Fax: [phone]
Sunstream Industries
Pte. Ltd.
18 Tuas South Street 5
Singapore 637796
Tel: [phone]
Fax: [phone]