Cascade E Series User manual

Manual Number 215204 R-1
Cascade is a Registered Trademark of Cascade Corporation
cascadeT
E-Series
Non-Sideshifting and
Sideshifting Clamps,
Carton Clamps
ERVICE MANUAL
S

Page
INTRODUCTION, Section 1
Introduction, 1.1 1
Special Definitions, 1.2 1
INSTALLATION, Section 2
Truck System Requirements, 2.1 2
Recommended Hydraulic Supply Options, 2.2 3
Clamp Installation Procedure, 2.3 4
PERIOD MAINTENANCE, Section 3
100-Hour Maintenance, 3.1 9
500-Hour Maintenance, 3.2 9
1000-Hour Maintenance, 3.3 9
TROUBLESHOOTING, Section 4
General Procedures, 4.1 10
Truck System Requirements, 4.1-1 10
Tools Required (metric), 4.1-2 10
Troubleshooting Chart, 4.1-3 11
Troubleshooting Carton Clamp Loads, 4.1-4 12
Plumbing, 4.2 14
Non-Sideshifting – Hosing Diagram, 4.2-1 14
Non-Sideshifting – Hydraulic Circuit, 4.2-2 15
Sideshifting – Hosing Diagram/Clamp, 4.2-3 16
Sideshifting – Hosing Diagram/Sideshift, 4.2-4 17
Sideshifting – Hydraulic Circuit, 4.2-5 18
Sideshifting/Regen. – Hydraulic Circuit, 4.2-6 19
Clamp Function, 4.3 20
Supply Circuit Test, 4.3-1 20
Clamp Circuit Test, 4.3-2 20
Sideshift Function, 4.4 21
Supply Circuit Test, 4.4-1 21
Sideshift Circuit Test, 4.4-2 22
Electrical Circuit, 4.5 23
ONTENTS
C
i
SERVICE, Section 5
Clamp Removal, 5.1 25
Arms, 5.2 26
Arm Assemblies – Removal and Installation, 5.2-1 26
Drum Arm Pad Surface Replacement, 5.2-2 27
Carton & Rigid Arm Pad Replacement, 5.2-3 28
Carton Clamp Pad, Stabilizer Repair, 5.2-4 29
Carton Clamp Camber Adjustment, 5.2-5 30
Clamps without Arms, 5.2-6 31
Arm Bearings – Removal and Installation, 5.2-7 32
Valve/Manifold, 5.3 33
Valve Removal and Installation, 5.3-1 33
Manifold Removal and Installation, 5.3-2 33
Valve Service, 5.3-3 34
Relief Valve Cartridge Adjustment, 5.3-4 36
Cylinders, 5.4 37
Cylinder Service, 5.4-1 37
Cylinder Disassembly, 5.4-2 37
Cylinder Inspection, 5.4-3 38
Cylinder Reassembly, 5.4-4 39
Cylinder Replacement, 5.4-5 41
Base Unit, 5.5 42
Baseplate Replacement, 5.5-1 42
Solenoid Valve, 5.6 43
Coil Service, 5.6-1 43
Valve Service, 6.6-2 43
SPECIFICATIONS, Section 6
Specifications, 6.1 44
Hydraulics, 6.1-1 44
Auxiliary Valve Functions, 6.1-2 44
Truck Carriage, 6.1-3 44
Torque Values, 6.1-4 45
Page

215204 Rev. 1 1
I
NTRODUCTION
1.1 Introduction
This Manual provides the Installation, Periodic Mainte-
nance, Troubleshooting, Service and Specifications for
Cascade E-Series Clamps.
E-Series Clamps are designed for three-shift-a-day
continuous-duty operations with minimal maintenance.
They offer exceptional visibility for the lift truck driver and
provide optimized clamp force and load handling.
In any communication about the Clamp, refer to the
product I.D. number stamped on the nameplate as shown.
If the nameplate is missing, the numbers can be found
stamped on the back of the baseplate.
IMPORTANT: All hoses, tubes and fittings on E-Series
Clamps are JIC.
NOTE: Specifications are shown
in both U.S. and (Metric) units.
1.2 Special Definitions
The statements shown appear throughout this Manual
where special emphasis is required. Read all WARNINGS
and CAUTIONS before proceeding with any work.
Statements labeled IMPORTANT and NOTE are provided
as additional information of special significance or to
make the job easier.
CAUTION - A statement preceded by CAUTION is
information that should be acted upon to prevent
machine damage.
IMPORTANT - A statement preceded by IMPORTANT is
information that possesses special significance.
NOTE - A statement preceded by NOTE is information
that is handy to know and may make the job easier.
WARNING - A statement preceded by
WARNING is information that should be
acted upon to prevent bodily injury. A
WARNING is always inside a ruled box.
45E-BC-005
cascade
LIFT TRUCK ATTACHMENT ATTACHMENT CAPACITY
SERIAL
NUMBER
CATALOG
NUMBER
ADDITIONAL
EQUIPMENT
ADDITIONAL
EQUIPMENT
ADDITIONAL
EQUIPMENT
FOR TECHNICAL ASSISTANCE, PARTS AND SERVICE
CONTACT:
1-800-227–2233
PORTLAND, OREGON USA
WEIGHT
LBS.
POUNDS
AT INCH LOAD
CENTER
CAPACITY OF TRUCK AND ATTACHMENT COMBINATION
MAY BE LESS THAN ATTACHMENT CAPACITY SHOWN
ABOVE. CONSULT TRUCK NAMEPLATE.
RECOMMENDED SYSTEM PRESSURE – 2000 PSI
MAXIMUM SYSTEM PRESSURE – 2300 PSI
cascade corporation
T
T
c
S/N 45E-BC-005
CL0412.ill
Nameplate

2 215204 Rev. 1
I
NSTALLATION
2.1 Truck System
Requirements
E-Series Clamps will provide maximum operating capabil-
ity when the following requirements are met.
WARNING: Rated capacity of the truck/
attachment combination is a responsibility of
the original truck manufacturer and may be
less than that shown on the attachment
nameplate. Consult the truck nameplate.
GA0082.ill
Clamp
Sideshift
Right
Tilt
Forward
Hoist Up
Auxiliary Valve Functions
Check for compliance with ITA (ISO) standards:
Tilt
Back
Hoist Down
Release
Sideshift
Left
GA0080.ill
Carriage
Clean carriage bars and inspect for
damaged notches
GA0028.ill
Carriage Mount Dimension (A) ITA (ISO)
Minimum Maximum
Class II 14.96 in. (380.0 mm) 15.00 in. (381.0 mm)
Class III 18.68 in. (474.5 mm) 18.74 in. (476.0 mm)
Truck Relief Setting
2300 psi (160 bar) Recommended
2600 psi (180 bar) Maximum
Truck Flow Volume ➀
Min. ➁Recommended Max. ➂
20E, 30E, 33E, 5 GPM 7.5 GPM 10 GPM
40E, 45E (19 L/min.) (28 L/min.) (38 L/min.)
➀Cascade E-Series Clamps are compatible with SAE 10W
petroleum base hydraulic fluid meeting Mil. Spec. MIL-0-5606 or
MIL-0-2104B. Use of synthetic or aqueous base hydraulic fluid is
not recommended. If fire resistant hydraulic fluid is required,
special seals must be used. Contact Cascade.
➁Flow less than recommended will result in reduced system
performance.
➂Flow greater than maximum can result in excessive heating,
reduced system performance and reduced hydraulic system life.
A

215204 Rev. 1 3
I
NSTALLATION
2.2 Recommended
Hydraulic Supply
Options
E-Series Clamps provide the best performance with one of
the hydraulic supply arrangements shown below. Refer to
Cascade
Hose and Cable Reel Selection Guide , Part No.
212119, to select the correct hose reel for the mast and
truck. The hose and fitting requirements are:
• All hoses and fittings for CLAMP and SIDESHIFT
functions should be at least No. 6 with a minimum
internal diameter of 9/32 in. (7 mm).
Non-Sideshifting
A or B
RH or LH THINLINE™2-port hose reel group.
OR
C Mast single internal hose reeving group.
Sideshifting
A and B
RH and LH THINLINE™ 2-port hose reel groups.
OR
C Mast double internal hose reeving group.
Sideshifting with Solenoid
A 6-N-1 cable/hose reel group.
OR
A and C
Cable reel and single internal hose reeving group.
B
A
GA0033.ill
C

4 215204 Rev. 1
I
NSTALLATION
2.3 Installation Procedure
Follow the steps shown to install the Clamp on the truck.
Read and understand all WARNING and CAUTION
statements. If you don't understand a procedure, ask your
supervisor, or call the nearest Cascade Service Depart-
ment for assistance.
2Unlock Quick-Change lower mounting hooks
ARemove pin and drop hooks into unlocked position.
BRe-install pin in lower hole.
1Prepare Attachment
ARemove banding, set Clamp upright on
pallet. Use multiple chains to stabilize
Clamp while lifting.
BRemove bolt-on lower mounting hooks
(if equipped).
Tighten Capscrews:
Class II / III Mounting – 165 ft.-lbs. (225 Nm)
cascade
®
C-675514-1
CL0097.ill
A
Pin
LH lower
Hook
NOTE: Guides can be reversed to
reduce hook-to-carriage clearance
(See lower hook installation, Step 6).
Guide
5/8-in. (16 mm)
offset on top
provides max.
clearance.
B
CL0096.ill B
A
WARNING: Make sure overhead
hoist has a rated capacity of at least
3500 lbs. (1600 kg).
A

215204 Rev. 1 5
I
NSTALLATION
Prepare Hoses
ADetermine hose lengths required for hydraulic
supply configuration of truck.
BCut hoses to length, install end fittings.
CL0589.ill
CL0585.ill
Sideshifting – Double Hose Reels
Sideshifting – Double Internal Hose Reeving
Sideshifting with Solenoid – IHR and Cable Reel
Sideshifting with Solenoid – 6-N-1 Cable/Hose Reel
OpenSideshift Left
Sideshift Right Clamp
CL0588.ill
CL0586.ill
SSL / Open
(TANK Port)
SSR / Clamp
(PRESSURE Port)
Flush hydraulic supply hoses
AInstall hoses using union fittings.
BOperate auxiliary valves for 30 sec.
CRemove union
fittings.
4
GA0092.ill
Non-Sideshifting – Single Hose Reel
CL0587.ill
Clamp
Open
Solenoid
Cable
3IMPORTANT: Main valve options include LH or RH
CLAMP/OPEN porting, or dual porting which allows
hoses to be plumbed to either side of the Clamp to
match existing truck hydraulic supply configurations.

6 215204 Rev. 1
I
CL0241.ill
NSTALLATION
5Mount Clamp on truck carriage
ACenter truck behind Clamp.
BTilt forward and raise carriage into position.
CEngage top mounting hooks with carriage.
Make sure centering tab engages a notch
on the top carriage bar. NOTE: Centering
tab can be oriented in 4 different positions
to center the Clamp (see illustration).
DLift Clamp 2 in. (5 cm) off pallet.
AB
ADJUST
SD0066.ill
Tighten Capscrews:
Class II / III Mounting – 165 ft.-lbs. (225 Nm)
Lower
Carriage
Bar
6Install and engage lower hooks
Tap tight into position.
Inspect hooks for
excessive clearance.
(Reverse guides to reduce
clearance – See Step 2.)
cascade
®
C-675514-1
SD0065.ill
3/16 in.
(5 mm)
Max.
Lower
Carriage
Bar
BOLT-ON TYPEQUICK-CHANGE TYPE
Slide hook up
to engage
bar, install
pin in upper
hole (locked.)
CL0243.ill
4
12
3
ITA Class II – 0.60–0.66 in. (15–17 mm)
ITA Class III – 0.72–0.78 in. (18–20 mm)
ITA Class II – 0.32–0.36 in. (8–9 mm)
ITA Class III – 0.39–0.43 in. (10–11 mm)
CL0242.ill
Truck
Carriage
Engage Tab
C
C
C
Notch
Centering Tab
Positions

215204 Rev. 1 7
I
NSTALLATION
Solenoid Coil
Connect hoses prepared in
Step 3 to Attachment
7
CL0247.ill
9Install wiring –
(Solenoid-equipped units)
c
PRESS
BUTTON
TO POSITION SIDESHIF
CL0240.ill
Button
toward
driver
Truck control
valve handle
Adapter
8Install solenoid control knob –
(Solenoid-equipped units)
CL0258.ill CL0257.ill
Solenoid Coil
User-supplied wire
7.5-Amp
Fuse
White Black
7.5-Amp Fuse
White Black
Solenoid Coil
Diode
Diode
Knob
Button
CL0104.ill
Double Hose Reels Hydraulic Supply Internal Hose Reeving Hydraulic Supply
Control Lever Knob
with Pushbutton

8 215204 Rev. 1
I
10 Cycle Clamp functions
•With no load, cycle each Clamp function
several times.
•Check for operation in accordance with
ITA (ISO) standards.
•Clamp and lift a maximum load. Sideshift
left and right. Check for equal arm
movement and adequate sideshift speed.
If necessary, adjust relief valve cartridges
(see Section 5.3-4).
•Check for leaks at fittings, valve, manifold
and cylinders.
AUXILIARY VALVE
FUNCTIONS
NSTALLATION
WARNING: Make sure all personnel are
clear of the Clamp during testing.
BD
C
A
GA0005.ill
NON-SIDESHIFTING CLAMPS
ARelease Arms
BClamp Arms
C (not used)
D (not used)
SIDESHIFTING CLAMPS
ASideshift Left
BSideshift Right
CRelease Arms
DClamp Arms
SIDESHIFTING CLAMPS WITH
SOLENOID VALVE
ASideshift Left
ARelease Arms
(press knob button)
BSideshift Right
BClamp Arms
(press knob button)
B
AA
BCL0022.ill
CL0023.ill
CL0274.ill
A
B
AA
B
CDC
A
Tilt Forward
Hoist Up Tilt Back
Hoist Down
11 Adjust relief valves
•For over-pressure protection, the relief
valves for both CLAMP and SIDESHIFT
functions should be adjusted to match the
truck hydraulic flow rate. See Section 5.3-4
for adjustment procedure.

215204 Rev. 1 9
ROUBLESHOOTING
T
WARNING: After completing any service
procedure, always test the Clamp
through five complete cycles. First test
the Clamp empty, then test with a load to
make sure the Clamp operates correctly
before returning it to the job.
IMPORTANT: E-Series Clamps are prelubed at the factory.
Lubrication is not necessary for installation.
3.1 100-Hour
Maintenance
Every time the lift truck is serviced or every 100 hours of
truck operation, whichever comes first, complete the
following maintenance procedures on the Clamp:
• Check for loose or missing bolts, worn or damaged
supply hoses and hydraulic leaks.
• Inspect the cylinder rod ends and anchor bars for
damage. The rod end anchors operate with a loose
clearance and require no lubrication.
• Check for equal movement of arms.
• Check decals and nameplate for legibility.
3.2 500-Hour
Maintenance
After each 500 hours of truck operation, in addition to the
100-hour maintenance, perform the following procedures:
• Inspect upper and lower bearing surfaces of each
arm for wear or damage. Lubricate with silicone spray or
light grease if required.
• Check the lower mounting hooks engagement clearance
with the truck carriage bar:
Quick-Change Hooks – 3/16 in. (5 mm) max.
Bolt-On Hooks – Tight against lower carriage bar.
If adjustment is necessary, refer to Installation Step 6.
Tighten lower hook capscrews to 165 ft.-lbs. (225 Nm).
3.3 1000-Hour
Maintenance
After each 1000 hours of truck operation, in addition to the
100 and 500-hour maintenance, perform the following
procedures:
• Tighten baseplate capscrews (see Table).
• Tighten cylinder rod anchor bar capscrews (see Table).
• Tighten contact pad mounting bolts to 50 ft.-lbs. (65 Nm).
Back (Driver's) View
CL0248.ill
Baseplate
Capscrews
CL0250.ill
Cylinder Rod
End Anchors
Bolt-On Lower
Mounting Hook
Contact Pad
Mounting Bolts
Left Side
Quick-Change
Lower Mounting
Hook
Torque Values
Model Baseplate Cyl. Rod Anchor
20E 75 ft.-lbs. 30 ft.-lbs.
(100 Nm) (40 Nm)
30E, 75 ft.-lbs.–M12 30 ft.-lbs.
33E (100 Nm) (40 Nm)
195 ft.-lbs.–M16
(265 Nm)
40E, 195 ft.-lbs. 50 ft.-lbs.
45E (265 Nm) (65 Nm)
Arm Bearings
ERIODIC MAINTENANCE
P
Cylinder Rod
End Anchor
Capscrews (8)

10 215204 Rev. 1
ROUBLESHOOTING
T
Pressure Gauge Kit 671212
Pressure
Gauge No. 6 and No. 8 JIC Swivel Tee
No. 4-6 Pipe/JIC
No. 6-6 Hose
Flow Meter Kit 671477
GA0013.ill
(2) No. 6-8 JIC Reducer
Flow Meter
No. 4, No. 6
and No. 8
JIC/O-Ring
No. 6-8 JIC
Reducer
(2) No. 8-12 JIC/
O-Ring
4.1 General Procedures
4.1-1 Truck System Requirements
• Truck hydraulic pressure should be within the range
shown in Specifications, Section 6.1. PRESSURE TO
THE CLAMP MUST NOT EXCEED 2600 psi (180 bar).
• Truck hydraulic flow should be within the range shown
in Specifications, Section 6.1.
• Hydraulic fluid supplied to the Clamp must meet the
requirements shown in Specifications, Section 6.1.
4.1-2 Tools Required (Metric)
In addition to a normal selection of hand tools, the
following are required:
• 20 GPM (75 L/min) inline flow meter.
(Cascade Flow Meter Kit, part no. 671477.)
• 3500 psi (240 bar) pressure gauge.
(Cascade Pressure Gauge Kit, part no. 671212.)
• Assorted fittings, lines, drain hoses and quick-couplers
as required. GA0014.ill
WARNING: Before servicing any
hydraulic component, relieve pressure in
the system. Turn the truck off and move
the truck auxiliary control valves several
times in both directions.
After completing any service procedure, always test
the Clamp through several cycles. First test the
Clamp empty to bleed any air trapped in the system to
the truck tank. Then test the Clamp with a load to be
sure it operates correctly before returning to the job.
Stay clear of the load while testing. Do not raise the
load more than 4 in. (10 cm) off the floor while testing.
AC0127.ill
Diagnostic Quick-Coupler
No. 4 and No. 6 Male
Straight or JIC Thread
O-ring Coupler
No. 6 Female
Straight Thread
O-ring Coupler

215204 Rev. 1 11
ROUBLESHOOTING
T
4.1-3 Troubleshooting Chart
Determine All The Facts – It is important to gather all
the facts about the problem before beginning any service
procedures. The first step is to talk to the equipment
operator. Ask for a complete description of the malfunc-
tion. Guidelines below and on the following pages can
then be used as a starting point to begin troubleshooting.
Clamp Circuit
• Clamp drops load after it has been picked up.
• Clamp will not carry load up to its rated capacity.
• Clamp arms have uneven travel.
• Clamp arms travel slowly.
• Clamp arms will not move.
To correct these problems, see Sections 4.3-1
and 4.3-2.
NOTE: Some Clamps have a regenerative hydraulic
circuit that causes the arms to open at a faster speed
than when closing. This is a normal Clamp function.
Sideshift Circuit
• Clamp drops load while sideshifting.
• Clamp drops load at end of sideshift stroke.
• Clamp sideshifts left and right at different speeds.
• Clamp will not sideshift.
To correct these problems, see Sections 4.4-1
and 4.4-2.
Carton Clamp Loads
• Front stack of load tilts out.
• Lower tier of load bridges down or slides out.
• Lower tier of load is creased.
To correct these problems, see Section 4.1-4.

12 215204 Rev. 1
ROUBLESHOOTING
T
4.1-4 Carton Clamp Loads
CL0086.ill
CL0087.ill
Re-clamp
load against
backrest
Check for bent
pads; straighten
or replace
IF FRONT STACK OF
LOAD TILTS OUT:
IF LOWER TIER OF LOAD BRIDGES
DOWN OR SLIDES OUT:
Check for bent
stabilizers;
straighten or
replace
Assure center of
load is between
pad pivot and
backrest
Check for bent
pads; straighten
or replace
Check for worn
lower surfaces,
rotate pads 180
°
and exchange
sides or replace
Re-clamp load
so bottom edge
is even with
bottom of pads
Check
hydraulics
for low
supply
pressure
Add or increase
positive camber
(Contact Cascade
Service)
IMPORTANT: Before adjusting contact pad camber to
solve handling problems, make sure the Clamp is being
used correctly and is not damaged. Use the Trouble-
shooting procedure shown and, if necessary, adjust the
contact pad camber using a Cascade Shim Service Kit.
1
2
3
4
5
1
2
3
4

215204 Rev. 1 13
ROUBLESHOOTING
T
CL0088.ill
Check for bent
pads; straighten
or replace
Re-clamp load
so bottom edge
is even with
bottom of pads
Check
hydraulics
for high
supply
pressure
Re-clamp load
squarely
between pads
IF LOWER TIER OF LOAD
IS CREASED:
CL0093.ill
TYPICAL PAD CAMBER FOR HANDLING CARTON CASE LOADS
CANNED / BOTTLED / DENSE CASE GOODS Neutral-to-Positive
SOFT CASE GOODS Neutral-to-Negative
APPLIANCE / LARGE CASE GOODS Neutral-to-Negative
UNKNOWN LOADS Start with neutral,
look for creases
and adjust camber
as required.
Front View – Pads
Add or increase
negative camber
(Contact Cascade
Service)
4.1-4 Carton Clamp Loads (Continued)
1
2
3
4
5

14 215204 Rev. 1
ROUBLESHOOTING
T
CL0347.ill
4.2 Plumbing
4.2-1 Non-Sideshifting Clamps –
Hosing Diagram
CLAMP ARMSRELEASE ARMS
Pressure:
Return:
OPEN Port
CLOSE Port
Hose Reel
or Internal
Reeving
Truck Auxiliary
Valve
Manifold
Cylinders (4)
Attachment Valve

215204 Rev. 1 15
ROUBLESHOOTING
T
4.2-2 Non-Sideshifting Clamps –
Hydraulic Circuit
CL0345.ill
OPEN
Port
Flow Divider/Combiner
CLOSE
Port
Manifold
Clamp
Release
Truck Relief
Valve
Truck Pump
2-Port
Hose Reel
or Internal
Reeving
Truck Auxiliary Valve
(Clamp/Release)
Truck Tank
Clamp
Check
Valve Clamp
Relief Valve
Cylinders (4)
TEST
Attachment Valve

16 215204 Rev. 1
ROUBLESHOOTING
T
CL0475.ill
4.2-3 Sideshifting Clamps –
Hosing Diagram, Clamp Circuit
OPEN
Port
CLOSE
Port
Hose Reel or
Internal Reeving
Truck Auxiliary
Valve
Manifold
Cylinders (4)
Attachment Valve
SSL
Port
SSR
Port
CL0476.ill
SSL / Release
(PRESSURE
Port)
Hose/Cable Reel
or Internal Reeving
Truck Auxiliary Valve
(with pushbutton)
Manifold,
Cylinders
Solenoid Valve
(energized)
OPEN
Port
CLOSE
Port
SOLENOID ADAPTION
CLAMP ARMSRELEASE ARMS
Pressure:
Return:
SSR / Clamp
(TANK Port)

215204 Rev. 1 17
ROUBLESHOOTING
T
4.2-4 Sideshifting Clamps –
Hosing Diagram, Sideshift Circuit
CL0348.ill
SIDESHIFT LEFT SIDESHIFT RIGHT
Pressure:
Return:
Slave:
OPEN Port
CLOSE Port
Hose Reel or
Internal Reeving
Truck Auxiliary
Valve
Manifold
Cylinders (4)
Attachment Valve
SSL
Port
SSR
Port
CL0349.ill
Hose/Cable Reel
or Internal Reeving
Auxiliary Valve
(with pushbutton)
Manifold,
Cylinders
Solenoid Valve
(not energized)
SSL
Port
SSR
Port
SOLENOID ADAPTION
SSL / Release
(PRESSURE
Port)
SSR / Clamp
(TANK Port)

18 215204 Rev. 1
ROUBLESHOOTING
T
4.2-5 Sideshifting Clamps –
Hydraulic Circuit
NOTE: Standard sideshift valve shown.
For sideshift with regeneration valve (arms
open faster than close), see Section 4.2-6.
CL0344.ill
OPEN
Port
Flow Divider/Combiner
SSL
Port SSR Port
Manifold
Sideshift
Check
Valves (2)
Sideshift
Relief
Valve
Clamp
Release/Sideshift
Truck Relief Valve
Truck Pump
2-Port Hose Reels (2) or
Internal Hose Reeving
Truck
Auxiliary
Valve
(Clamp/
Release)
Truck Tank
Clamp
Check Valve
Clamp
Relief
Valve
Cylinders (4)
TEST
Attachment Valve
Truck
Auxiliary
Valve
(Sideshift)
CLOSE
Port
CL0477.ill
Solenoid Adaption
Truck Auxiliary Valve
(Sideshift/Clamp)
Solenoid Valve
2-Port Hose/Cable Reel
TANK
Port PRESSURE
Port