Casio 5411 User manual

Basic Operations
This section provides an overview of the
watch and its operations.
Note
●The illustrations included in this
manual have been created to
facilitate explanation. An
illustration may differ somewhat
from the item it represents.
General Guide
30
③①②
⑤
④
⑥⑦⑧
⑨
AHour hand
BSecond hand
CMinute hand
D24-hour hand
ESmall minute hand
FSmall hour hand
GMode hand
HDay indicator
ICrown
Watch Face Items
①
②
③
④
⑤
⑥
⑦
⑨
⑧
⑩
⑪
⑫
⑬
ASignal receive result
BAlarm off
CAlarm on
DTime calibration reception in
progress
EGPS signal time information and
position information acquisition in
progress
FGPS signal time information
reception in progress
GSummer time setting
MA1409-EB © 2014 CASIO COMPUTER CO., LTD.
HApproximate latitude
(N side: North latitude, S side: South
latitude)
IDay of the week
JAirplane Mode
KStopwatch Mode
LTimer Mode
MAlarm Mode
Navigating Between Modes
Your watch has four modes.
You tell which mode the watch is
currently in by checking the position of
the mode hand.
●Timekeeping Mode (normal
timekeeping): Current day of the week
●Stopwatch Mode: ST (STW)
●Timer Mode: TR
●Alarm Mode: AL
CC
CC
Timekeeping Mode
30
30
30
30
Mode hand
Alarm Mode
Timer Mode
Stopwatch Mode
Use the (C) button to navigate between
modes.
●Hold down (C) for at least two seconds
to return to the Timekeeping Mode.
●Holding down (C) for four seconds or
longer will enter or exit the Airplane
Mode. The mode hand points to h
while the watch is in the Airplane Mode.
l Using the Watch on an Aircraft
Using the Crown
The watch’s crown is a screw-in (screw
lock) type. To use the crown, you first
need to rotate it towards you (leftwards)
to loosen it.
Loosen
Crown
Important!
●To prevent loss of water
resistance and/or damage due
to impact, be sure to push the
crown in and lock it when not in
use.
●When pushing the crown back
in, take care not to apply too
much force.
●Fast Forward/Fast Reverse
Normal position
Second click
First click
Crown
After pulling out the crown to the first or
second click, rotating it quickly in
succession in either direction will start a
fast forward or fast reverse operation.
While a fast forward operation is in
progress, quickly rotating the crown in
succession again will increase the speed
even further.
●The fast reverse operation speed is
fixed and cannot be changed.
●Stopping Fast Forward/Fast
Reverse
Rotate the crown in the direction
opposite that of the ongoing operation or
press any button.
Operation Guide 5411
1

Note
●If you do not perform any
operation for about two minutes
after pulling out the crown,
crown operations will
automatically become disabled.
If that happens, push the crown
back in and then pull it out again.
Solar Charging
What is solar charging?
This watch runs on power supplied from
a rechargeable (secondary) battery that
is charged by a solar panel. The solar
panel is integrated into the face of the
watch, and power is generated
whenever the face is exposed to light.
●This watch uses a special
rechargeable (secondary) battery.
ーThe watch’s battery will not charge if
the watch’s temperature is less than
approximately -10°C (14°F) or
greater than approximately 60°C
(140°F).
ーOver-discharge will occur if the
watch is not charged within
approximately three months after it
stops operation due to low battery
power. Charging may not be
possible after over-discharge
occurs.
Charging the Watch
When you are not wearing the watch, put
it in a location where it is exposed to
bright light.
While you are wearing the watch, make
sure that its face (solar panel) is not
blocked from the light by the sleeve of
your clothing. Power generation
efficiency is reduced even when the face
of the watch is blocked only partially.
NOYES
Important!
●If the second hand stops for
some time after the watch is
continuously exposed to light, it
could mean that charging is not
possible due to over-discharge.
Request chargeable
(secondary) battery
replacement by your original
retailer or authorized CASIO
service center.
●Depending on light intensity and
local conditions, the watch may
become hot to the touch when
exposed to light for charging.
Take care to avoid burn injury
after charging. Also, avoid
charging the watch under high-
temperature conditions like the
ones described below.
ーOn the dashboard of a vehicle
parked in the sun
ーNear an incandescent light
bulb or other source of heat
ーUnder direct sunlight or in
other hot areas for long
periods
Note
●Exposing the watch face to light
after the battery goes dead will
cause the second hand to
revolve counterclockwise until it
stops at second 57. This
indicates charging has started.
●A fully charged watch can
operate for approximately
seven months without further
charging. Watch operation will
stop approximately 20 days
after the battery goes low.
Charging Times
Light Intensity Charge
Level 1
Charge
Level 2
High
p
Low
A8 hours 27 hours
B26 hours 102 hours
C41 hours 165 hours
D450 hours -
Charge Level 1:
Time from dead battery until hand
movement starts
Charge Level 2:
Time from hand movement starts until a
full charge
Light Intensity
ASunny day, outdoors (50,000 lux)
BSunny day, near a window (10,000
lux)
COvercast day, near a window (5,000
lux)
DIndoor fluorescent lighting (500 lux)
Note
●Actual charging time depends
on the local charging
environment.
Operation Guide 5411
2

Checking the Charge Level
The charge level is indicated by watch
hand movement. Functions become
disabled as battery power goes low.
Important!
●Should battery go low or go
dead, expose the face (solar
panel) to light as soon as
possible.
Immediately after pressing (C) to enter to
the Timekeeping Mode, the second hand
will move to one of the positions below to
indicate the battery charge level.
●Battery Charged
2 o'clock12 o'clock
●Low Battery Power
6 o'clock4 o'clock
Also, the second hand jumps at two-
second or five-second intervals.
30
30
Second hand
Two-second intervals Five-second intervals
●Above right figures indicate a lower
battery charge.
●Dead Battery
All hands are stopped.
1
Power Saving Function
Leaving the watch in a dark location for
about one hour between the hours of 10
p.m. and 6 a.m. will cause the second
hand to stop, and the watch will enter
Level 1 power saving. If the watch is left
in this condition for six or seven days, all
hands will stop and the watch will enter
Level 2 power saving.
Level 1:
Basic timekeeping functions are
operational.
Level 2:
Only the day indicator is operational.
Note
●Note that the watch also may
enter the power saving state if its
face is blocked from light by your
sleeve while you are wearing it.
●The watch will enter power
saving from the Timekeeping
Mode only.
●Recovering from Power Saving
Operation
Press any button or place the watch in a
well-lit area to recover from power
saving.
Time Adjustment (GPS,
Time Calibration Signal)
The watch’s time, day, and Home City
(time zone) settings can be configured in
accordance with a received GPS signal
or time calibration signal.
●GPS signal position information: Used
to update Home City (time zone), time,
and day settings.
●GPS signal time information: Used to
update time and day settings.
●Time calibration signal: Used to update
time and day settings.
Important!
●Before trying to receive GPS
signal time information and/or a
time calibration signal, first use
GPS to acquire position
information and configure
Home Time (time zone)
settings.
●Put the watch into the Airplane
Mode whenever you are inside
an aircraft or in any other area
where radio wave reception is
prohibited or restricted.
l Using the Watch on an
Aircraft
Note
●Areas where time calibration
signal reception is supported
are limited. When the watch in
an area where time calibration
signal reception is not
supported, adjust time and day
settings based on GPS signals.
l Time Calibration Signal
Reception Ranges
Operation Guide 5411
3

Time Adjustment Using GPS
Appropriate Signal Reception
Location
GPS signal reception is possible
outdoors where the sky is visible and not
blocked by buildings, trees, or other
objects.
Note
●In areas where reception is
poor, keep the watch face
oriented upwards and do not
move the watch.
●When the watch is set up for
auto receive, take care to avoid
covering the watch face with the
sleeve of your clothing.
●GPS signal reception is not
possible in the areas described
below.
ーWhere the sky is not visible
ーIndoors (Reception may be
possible near a window.)
ーNear wireless communication
equipment or other devices
that generate magnetism.
●You may experience GPS signal
reception problems in the areas
described below.
ーWhere the view of the sky
above is narrow
ーNear trees or buildings
ーNear a train station, airport, or
other congested areas
Acquiring GPS Position
Information Manually
You can use a button operation to
acquire GPS position information and
adjust your Home City (time zone), time,
and day settings in accordance with your
current location.
Note
●GPS signal reception requires
large amounts of power.
Perform it only when necessary.
Getting ready
The receive operation is performed only
while the watch is in the Timekeeping
Mode (normal timekeeping).
●Normally the mode hand points to the
current day of the week.
l Navigating Between Modes
30
Mode
hand
1. Move to a location appropriate for
signal reception and orient the watch
so its display is pointed straight up at
the sky.
2. Hold down (B) for at least three
seconds. Release the button as soon
as the second hand points to “T+P”.
●The second hand will move in the
following sequence: “YES” or
“NO” n “T (TIME)” n “T+P”.
●This indicates that position
information acquisition has
started. The mode hand will rotate
a number of times while
information acquisition is in
progress.
30
Mode hand
Second hand
●If position information acquisition
is successful, the second hand will
move to “YES” and then the watch
will automatically adjust its time
and day settings. The watch will
also display the acquired Home
City (time zone) and the
approximate latitude of your
current position.
30
Latitude
●If position information acquisition
fails for some reason, the second
hand will move to “NO” and then
the watch will indicate the current
time and day without adjusting
them.
Note
●Reception takes anywhere from
about 30 seconds to about two
minutes.
●It can take as long as 13 minutes
when leap second information is
included.
●You may experience location
information acquisition
problems when you are in the
vicinity of a time zone
borderline.
The watch’s time and day will
not be indicated correctly if the
Home City (Time Zone) setting
is not right for your location.
Perform position information
acquisition in a representative
city in your time zone or in a
location that is well within the
time zone. Or you can perform a
time information receive
operation to adjust time and day
settings after configuring Home
City (Time Zone) and summer
time settings manually.
l Selecting a Time Zone
l Acquiring GPS Time
Information Manually
Operation Guide 5411
4

Acquiring GPS Time Information
Manually
You can use a button operation on the
watch to receive GPS signal time
information. When the receive operation
is successful, the watch’s Home City
(time zone), day, and time settings will be
adjusted accordingly.
Note
●GPS signal reception requires
large amounts of power.
Perform it only when necessary.
Getting ready
The receive operation is performed only
while the watch is in the Timekeeping
Mode (normal timekeeping).
●Normally the mode hand points to the
current day of the week.
l Navigating Between Modes
30
Mode
hand
1. Move to a location appropriate for
signal reception and orient the watch
so its display is pointed straight up at
the sky.
2. Hold down (B) for at least one
second. Release the button as soon
as the second hand points to “T
(TIME)”.
●The second hand will move in the
following sequence: “YES” or
“NO” n “T (TIME)”.
●This indicates that time
information receipt has started.
30
Second hand
●If information acquisition is
successful, the second hand will
move to “YES”, and then the watch
will automatically adjust its time
and day settings.
30
●If reception fails for some reason,
the second hand will move to “NO”
and then the watch will indicate the
current time and day without
adjusting them.
Note
●Reception takes anywhere from
about seven seconds to about
one minute.
●It can take as long as 13 minutes
when leap second information is
included.
Auto GPS Signal Receive
When the conditions below are satisfied,
the watch will automatically receive a
GPS signal. If any time information
receive is successful, the watch will no
longer attempt to receive a signal for the
rest of the day.
●Time data
●Watch is in the Timekeeping Mode
(normal timekeeping).
●Current time is between 6:00 a.m. and
10:00 p.m.
●Light (near a window on a clear day)
continually shining on the face of the
watch for about one to two minutes.
●Time calibration signal reception was
not successful during the previous
evening.
●Position information
●Watch is in the Timekeeping Mode
(normal timekeeping).
●The watch exited the Airplane Mode.
●Current time is between 6:00 a.m. and
10:00 p.m.
●Light (near a window on a clear day)
continually shining on the face of the
watch for about one to two minutes.
Note
●The time information receive
operation takes anywhere from
about seven seconds to one
minute, while position
information acquisition takes
anywhere from about 30
seconds to two minutes.
●The receive operation can take
as long as 13 minutes when leap
second information is included.
Leap seconds
A GPS signal received on or around June
1 or December 1 each year may also
include leap second information.
Note
●The receive operation can take
as long as 13 minutes when leap
second information is included.
●Once leap second information is
successfully received, the
watch will not make any attempt
to receive it again until the next
leap second information is sent
(the following June 1 or
December 1).
Operation Guide 5411
5

Time Adjustment Using a
Time Calibration Signal
Appropriate Signal Reception
Location
A time calibration signal can be received
while the watch is near a window.
●Keep metal objects away from the
watch.
●Do not move the watch.
●Do not perform any operation on the
watch.
12 o'clock
Note
●You may experience time
calibration signal reception
problems in the areas described
below.
ーAmong or near buildings
ーWhile riding in a vehicle
ーNear household appliances,
office machines, mobile
phones, etc.
ーOn a construction site, in an
airport, or any other location
where radio wave
interference occurs
ーNear high-voltage lines
ーIn mountainous areas or
behind a mountain
Time Calibration Signal Reception
Ranges
Time calibration signal reception is
supported in the areas shown below.
●Japan Time Calibration Signal
(JJY)
500 kilometers
500 kilometers
1,000 kilometers
1,000 kilometers To k y o
Fukushima
Fukuoka/
Saga
●
Chinese Time Calibration Signal
(BPC)
500 kilometers
1,500 kilometers
Chengdu
Shangqiu
Hong Kong
Shanghai
Beijing
Changchun
●U.S. Time Calibration Signal
(WWVB)
600 miles
(1,000 kilometers)
2,000 miles (3,000 kilometers)
Los Angeles
Denver
Fort Collins
Chicago
New York
●U.K. (MSF) and German (DCF77)
Time Calibration Signal
The Anthorn signal is receivable within this area.
500 kilometers
1,500 kilometers
Mainflingen
Anthorn
Note
●Even if you are within the normal
reception range of a time
calibration signal, reception
may be made impossible by the
following factors: geographic
contours, weather, the season,
the time of day, wireless noise.
Auto Time Calibration Signal
Receive
An automatic time calibration signal
receive operation is performed and the
time and day settings are adjusted
between midnight and 5:00 a.m. Once a
signal receive operation is successful, no
more auto receive operations are
performed that day.
The receive operation is performed only
while the watch is in the Timekeeping
Mode (normal timekeeping).
●Normally the mode hand points to the
current day of the week.
l Navigating Between Modes
30
Mode
hand
Place the watch near a window or some
other location appropriate for signal
reception.
●The second hand points to “RC” while
time calibration reception in progress.
●When the receive operation is
successful, the time and day settings
will be adjusted automatically.
Note
●Reception takes anywhere from
about two minute to about 10
minutes. It can take as long as
20 minutes.
Operation Guide 5411
6

Checking the Receive
Operation Result
You can use the procedure below to
check the result of the last GPS or time
calibration signal receive operation.
Getting ready
Enter the Timekeeping Mode.
l Navigating Between Modes
1. Press (B).
The second hand will move and
indicate the receive operation result.
“YES”: Receive successful
“NO”: Receive failed
30
Second hand
2. Press (B) or do not perform any
operation for one or two seconds to
return to the current time.
Note
●Even if there was a successful
receive operation, the second
hand will point to “NO” if you
adjusted the time setting
manually.
●If you do not perform any watch
operation for about one or two
seconds after position
information is acquired, the
watch will display the acquired
Home City (time zone) and the
rough latitude of your current
position.
30
Latitude
Home City
Signal Reception
Precautions
●GPS signal and time calibration signal
reception will not be possible under
any of the watch conditions described
below.
ーWhile battery power is low
ーWhile the watch is in the Airplane
Mode, Stopwatch Mode, Timer
Mode, or Alarm Mode
ーWhen power saving is at Level 2
(GPS signal reception also is not
possible at Level 1.)
ーWhile the crown is pulled out
ーWhile a stopwatch elapsed time
measurement and/or timer
countdown operation is in progress
ーWhile the temperature of the watch
is less than approximately -10°C
(14°F) or greater than approximately
60°C (140°F)
●Note that an internal decoding process
the watch performs after it receives a
signal may cause the time setting to be
slightly off (by less than one second).
●If the receive operation is successful,
the time and day settings will be
adjusted automatically in accordance
with the Home City (time zone) and
summer time settings. Summer time
will not be applied correctly in the
cases described below.
ーWhen the summer time start date
and time, end date and time, or other
rules are changed by authorities
ーWhen position information cannot
be acquired correctly
ーWhen position information can be
acquired, but it is wrong because the
watch is located near a time zone
boundary, etc.
●As of December 2013, China does not
observe summer time. If China starts to
observe summer time in the future, the
time displayed by the watch for China
may not be correct.
●When the watch is unable to adjust its
time in accordance with a calibration
signal for some reason, average
timekeeping accuracy is within ±15
seconds per month.
Using the Watch on an
Aircraft
Enter the Airplane Mode when in an
aircraft or anywhere else where GPS or
time calibration signal reception is
restricted.
Entering the Watch Airplane
Mode
Holding down (C) for about four seconds
to enter the watch’s Airplane Mode. The
mode hand will move to the Airplane
mark.
30
Airplane mark
●Each time the (C) button is held down
for about four seconds, the watch
enters or exits the Airplane Mode.
World Time
World Time lets you look up the current
time in any one of 27 cities and 40 time
zones around the globe.
Getting ready
Enter the Timekeeping Mode.
l Navigating Between Modes
Checking the Time in
Another Zone
1. Pull out the crown to the first click.
The hands of the watch will move to
the current time in the currently
selected World Time City.
30
Time zone
Small hour hand
Small minute hand
Crown
Operation Guide 5411
7

2. Rotate the crown to change the time
zone.
The small hour hand and small
minute hand indicate the current
time in the selected time zone.
●Hold down the (B) button for about
one second to display UTC
(Universal Time Coordinated)
time.
30
Small hour hand
Small minute hand
Crown
3. Hold down the (A) button for about
one second to change the summer
time setting.
●Each press of (A) cycles through
available settings in the sequence
shown below.
“AT (AUTO)” n “STD” n “DST”
30
●“AT (AUTO)”
The watch switches between
standard time and summer time
automatically.
●“STD”
The watch always indicates
standard time.
●“DST”
The watch always indicates
summer time.
4. Push the crown back in.
Note
●When a time zone for which
there is no city name displayed
is selected, use “STD” or “DST”
for the summer time setting.
●You cannot switch between
“STD” and “DST” while “UTC” is
selected as the Home City (time
zone).
Stopwatch
The stopwatch measures elapsed time in
units of 1/20 (0.05) seconds up to 23
minutes, 59.95 seconds (24 minutes).
Getting ready
Enter the Stopwatch Mode.
l Navigating Between Modes
30
Measuring Elapsed Time
30
Stopwatch 1/20 (0.05)-second
Mode hand
Stopwatch
minutes,
seconds
1. Use the operations below to
measure elapsed time.
A
A
A
A
Start
Stop
Resume
Stop
●The stopwatch 1/20 (0.05)-second
hand will move for the first 30
seconds after an elapsed time
measurement operation is started,
and then stop. When the elapsed
time measurement operation is
stopped, the hand will move to the
appropriate position to indicate the
final 1/20 (0.05)-second count.
2. Press (B) to reset the elapsed time to
all zeroes.
3. Press (C) three times to return to the
Timekeeping Mode.
Timer
The timer counts down from a start time
specified by you. A beeper sounds when
the end of the countdown is reached.
●The beeper is muted in the cases
described below.
ーWhen battery power is low
ーWhen watch is at Level 2 power
saving
l Power Saving Function
Getting ready
Enter the Timer Mode.
l Navigating Between Modes
30
Setting the Timer Start Time
1. Pull out the crown to the first click.
2. Rotate the crown to change the
countdown start time setting.
●The countdown start time can be
set in 1-minute units up to 24
hours.
30
Seconds
Minutes
Hours
Crown
3. Push the crown back in.
Note
●When the small hour hand and
small minute hand are at 12
o’clock, a countdown start time
of 24 hours is specified.
Operation Guide 5411
8

Using the Timer
1. Press (A) to start the countdown.
30
A beeper sounds when the end of the
countdown is reached.
●To pause an ongoing countdown,
press (A). To reset a paused
countdown to the start time, press
(B).
2. Press any button to stop the tone.
3. Press (C) twice to return to the
Timekeeping Mode.
Alarms
The watch will beep when the alarm time
is reached.
●The beeper is muted in the cases
described below.
ーWhen battery power is low
ーWhen watch is at Level 2 power
saving
l Power Saving Function
Getting ready
Enter the Alarm Mode.
l Navigating Between Modes
30
Configuring Alarm Settings
1. Pull out the crown to the first click.
This turns on the alarm.
2. Rotate the crown to change the alarm
time setting.
30
Alarm on
Alarm hour/minute
Crown
3. Push the crown back in.
4. Press (C) once to return to the
Timekeeping Mode.
Enabling/Disabling the
Alarm
Press (B) to toggle the alarm between on
and off.
30
Alarm on
Alarm off
Stopping an Alarm
While the alarm is sounding, press any
button to stop it.
Illumination Light
The watch has an LED light that you can
turn on for reading in the dark. When you
turn on the LED light, it gradually
becomes brighter. After about two
seconds, it gradually becomes dimmer
until it turns off.
Getting ready
Enter the Timekeeping Mode or Alarm
Mode.
l Navigating Between Modes
Turning On the Illumination
Light
Pressing (A) turns on the light.
30
●The LED light will turn off automatically
if the alarm starts to sound.
●The LED light is disabled while the
hands are moving at high speed.
Adjusting Time Settings
Manually
You can use the procedure below to
adjust the watch’s time and day settings
when GPS and time calibration signal
reception is not possible for some
reason.
Selecting a Time Zone
Use the procedure in this section to
select a city (time zone) to use as your
Home City. If you are in an area that
observes summer time, you can also
enable or disable summer time.
Operation Guide 5411
9

Note
●The initial factory default
summer time setting for all cities
(time zones) is “AT (AUTO)”.
With this setting, the watch
automatically switches between
summer time and standard time
as required. The “AT (AUTO)”
setting lets you use the watch
without worrying about
changing the summer time
setting.
●When performing a manual
operation to select a time zone
for which there is no city name
displayed, use “STD” or “DST”
for the summer time setting.
●In the cases described below,
receiving GPS position
information will automatically
cause “AT (AUTO)” to be
selected for the summer time
setting.
ーWhen the time zone of the
current receive operation is
different from the watch’s time
zone setting prior to the
receive operation.
ーWhen the time zone is
unchanged, but the acquired
position information is for a
geographic area with different
summer time rules (start date,
end date)
1. Pull out the crown to the second click.
The second hand will move to the
currently selected time zone.
30
Crown
Time zone
2. Rotate the crown to change the time
zone.
●You can also select a time zone
whose name is not indicated on
the face of the watch.
●For information about time zones,
see the “City (Time Zone) List”.
3. Hold down (A) for about one second
to change the summer time setting.
●Each press of (A) cycles through
available settings in the sequence
shown below.
“AT (AUTO)” n “STD” n “DST”
30
●“AT (AUTO)”
The watch switches between
standard time and summer time
automatically.
●“STD”
The watch always indicates
standard time.
●“DST”
The watch always indicates
summer time.
4. Push the crown back in to its normal
position.
Summer Time
Summer time, which is also known as
Daylight Saving Time (DST), advances
the time setting one hour, 30 minutes, or
some other amount of time from standard
time (STD) during the summer months.
Whether or not and how summer time is
used depends on your country or local
area. Summer time is not used in some
countries and local areas.
Adjusting the Time and Day
Setting
1. Pull out the crown to the second click.
The second hand will move to the
currently selected time zone.
30
Hours Minutes
Crown
Time zone
2. Hold down (C) for about 10 seconds.
This causes the second hand to
move to 12 o’clock and enables the
hour and minute setting operation.
3. Rotate the crown to adjust the hour
and minute settings.
4. Press (C).
This enables the year 10’s digit
setting operation.
80
90 30
40
20
50
70
10
60
00
＋
−
Year (10’ s digit)
5. Rotate the crown to move the second
hand to the desired setting for the
year ten’s digit.
6. Press (C).
This enables the year one’s digit
setting operation.
8
93
4
2
5
7
1
6
0
＋
−
Year (1’ s digit)
7. Rotate the crown to move the second
hand to the desired setting for the
year one’s digit.
Operation Guide 5411
10