Casio 5517 User manual

1
Operation Guide ANA(H3H-1)
MA1710-EA © 2017 CASIO COMPUTER CO., LTD.
Stopwatch functions
Crown Operations
Some water-resistant models (100 meters, 200 meters)
have a screw-in crown. When you need to perform a crown
operation, rotate it towards you to unscrew it. Then pull
the crown out. Avoid applying undue force when pulling.
The watch loses its water resistance while the crown is
unscrewed. After performing a crown operation, fully screw
the crown back in.
Crown
Loosen
If your watch has a rotary bezel...
You can rotate the bezel to align its ▼mark with the
minute hand. Then you will be able to tell how much
time has elapsed since aligning the ▼mark.
Start
Elapsed time
Current
xBe sure to keep all user documentation handy for future reference.
xYour watch may differ somewhat from the one shown in the illustration.
xSome models may use a combination of hands and rotating disks to indicate
information. The word “hand” in this section is used to mean both analog hands
and rotating disks.

Second Hand
Day Indicator
Click 2
Click 1
Hour Hand Minute Hand
A
B
Crown
Stopwatch Minute Hand
Stopwatch 1/10-Second Hand
Stopwatch Second Hand
To change the day indicator setting To adjust the time setting
Pull the Crown out to Click 1.
Push the Crown back in.
Rotate the Crown to change the
time setting.
When the second hand is at
12 o’clock, pull the Crown out to
Click 2.
Rotate the Crown away from you
to set the day.
Note
xTake care that you set the correct AM
or PM time.
xWhen changing the time, move the
minute hand four or five minutes past
your final setting, and then back it up
to the setting you want.
Note
xThe day indicator setting uses a 31-
day month. Make adjustments for
months of shorter lengths.
xAvoid changing the day indicator
setting between the hours of 9
p.m. and 1 a.m. Otherwise, the day
indicator may not change correctly at
midnight.
Push the Crown back in on a time
signal to resume timekeeping.
Specifications
Module No. Accuracy at normal
temperature (per month) Battery type Battery life
(60 minutes stopwatch
operation per day)
5517/5521 ±20 seconds SR920SW Approx. 2 years
5579 ±20 seconds SR920SW Approx. 3 years
Stopwatch: Measuring Capacity: 59'59.9" (60 minutes)
Measuring Unit: 1/10 second
Measurements: Elapsed time; split time; two finishes
Specifications are subject to change without notice.
Using the Stopwatch
Elapsed time
AAAAB
Start Stop Resume Stop Reset
Split time
ABBAB
Start Split Split release Stop Reset
Two finishes
ABABB
Start Split
First runner
finishes.
Display time of first
runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Reset
Important!
xDo not operate the stopwatch with the crown pulled out.
Note
xAn elapsed time operation will stop automatically at the end of 60 minutes.
The stopwatch measures elapsed time in 1/10-second increments up to 59minutes,
59.9seconds.
Perform the following procedure if the stopwatch hands do not return to their 0 (zero)
positions when you reset the stopwatch.
Correcting the 0 Positions of the Hands
Pull the Crown out to Click 2.
Press Ato move the Stopwatch 1/10-Second Hand clockwise.
xHolding down Awill move the hand at high speed.
Press Bto move the Stopwatch Second Hand clockwise.
xHolding down Bwill move the hand at high speed.
xThe Stopwatch Minute Hand is synchronized with the Stopwatch Second Hand .
After all of the hands are the way you want, push the Crown back in.
Important!
xTimekeeping stops while the crown is pulled out. Correct the current time setting
after performing the above operation.