Cassida PRO Series User manual

®
USER MANUAL
Zeus 2-Pocket Currency Discriminator

®
Zeus

Battery Warning: (1) Keep out of the reach of children. Swallowing may lead to serious
injury or death in as little as 2 hours due to chemical bums and potential perforation of the
esophagus. Immediately see doctor; have doctor phone [phone]. Keep in original
package until ready to use. Dispose of used batteries immediately. (2) Risk of injury due
to re, explosion or leakage. Do not disassemble, charge, crush or expose to re or high
temperatures. California Only: Perchlorate material - special handling may apply.
California Proposition 65 Warning: This product contains chemicals known to the
State of California to cause cancer and birth defects or other reproductive harm.
Warning: Moving parts present. May cause serious injury to hands or ngers.

In the event of incorrect operation or care of the unit, the manufacturer is not responsible
for damage caused to the unit or the operator. Cassida is not liable for damages
resulting from use of the unit for purposes other than for the intended purpose without
prior written consent from Cassida. Modications made to the unit by persons other than
Cassida or its authorized contractor/subcontractor are strictly prohibited. Any damages
resulting from the unauthorized modication of the unit are not the responsibility
of Cassida. For proper installation and/or transport of the unit, please consult an
authorized Cassida distributor or sales representative.
Please Note:
• The contents of this manual are subject to change without notice.
• While every effort has been made to include all the features and functionality of
your unit, specications stated in this manual may not reect all the features of
software updates. You may encounter differences in operation or functionality of
your unit.
• No part of the manual may be reproduced for commercial purposes without prior
written consent from Cassida.
• Due to power and safety specications, this product has been developed for use in
specic countries as described in the specications. Use in unspecied countries
is prohibited.
• This equipment has been tested and complies with the limits to a Class A digital
device, pursuant to Part 15 of the FCC Rules.
If you have questions about the operation of the Cassida Pro Series Zeus, please contact your
Cassida licensed reseller or refer to Cassida’s user portal at www.CassidaPro.com.
IMPORTANT SAFETY INSTRUCTIONS
When using this unit, basic safety precautions should always be observed including:
• Read this manual in its entirety.
• Do not use areas that could expose the unit to water or other liquids.
• Install on a at surface.
• Do not use in areas exposed to high temperature, humidity or smoke.
• For indoor use only.
• Store and operate the unit in a well ventilated environment and away from direct
sunlight, high intensity lighting, and magnetic elds that could interfere with suspect
bill sensors.
• Do not touch moving parts during operation.
• Keep foreign objects - paper clips, staples, etc. - away from moving parts or from
falling into the unit.
• Operate using a surge suppressor or power conditioner. When not in operation for
extended periods of time, disconnect the power cord.
• Prior to and during cleaning, unplug the unit. Follow the cleaning instructions and
maintenance schedule contained in this manual.
• Do not service your unit. Contact your authorized Cassida Pro technician,
distributor or sales representative for technical assistance.

Table of Contents:
1. INTRODUCTION
1.1 About the Cassida Pro Series Zeus ______________________________________1
1.2 Box Contents _______________________________________________________1
1.3 Views of the Cassida Pro Series Zeus ____________________________________2
1.4 Control Panel _______________________________________________________3
1.5 Display ____________________________________________________________ 5
1.6 Glossary of Terms ___________________________________________________6
2. OPERATION
2.1 Getting Started _____________________________________________________6
2.2 Loading Bills________________________________________________________ 7
2.3 Counting Modes ____________________________________________________8
2.3.1 [MIX]: MIX Mode ___________________________________________________8
2.3.2 [SORT]: SORT Mode _________________________________________________9
2.3.3 [CNT]: COUNT Mode ________________________________________________9
2.3.4 [FACE]: FACE Mode ________________________________________________ 10
2.3.5 [ORT]: ORIENTATION Mode _________________________________________10
2.3.6 [VSORT]: VALUSORT Mode __________________________________________ 11
2.4 [ADD]: Adding/Sum Function _________________________________________ 11
2.5 [STRAP]: Strapping/Batching Function __________________________________ 12
2.5.1 STRAP by Number __________________________________________________ 13
2.5.2 STRAP by Amount __________________________________________________ 13
2.5.3 STRAP by Denomination _____________________________________________ 13
2.6 [REPRT]: Post-Count Summary and Detail ________________________________ 14
2.6.1 [+GT]: Add to Grand Total ___________________________________________ 14
2.6.2 [PRINT]: Print Totals Function__________________________________________ 15
2.6.3 [REJCT]: View Reject Report and Reasons________________________________ 15
2.7 Manual Entry of Rejected Bills to Count Total _____________________________ 15
3. MENU SETTINGS AND DESCRIPTIONS
3.1 Auto/Manual Start _________________________________________________ 16
3.2 Speed____________________________________________________________ 16
3.3 Mode Enable/Disable _______________________________________________ 17
3.4 Counterfeit Settings _________________________________________________ 17
3.5 Settings Menu _____________________________________________________ 18
3.5.1 Date & Time _______________________________________________________ 18
3.5.2 Print/Interface/Beep ________________________________________________ 19
3.5.3 Thousands Seperator ________________________________________________20
3.5.4 Maintenance Reminder ______________________________________________ 21
3.5.5 Language_________________________________________________________22
3.5.6 Clear Remote Count_________________________________________________22
3.5.7 Pocket Capacity ____________________________________________________23
3.5.8 LAN Settings ______________________________________________________23
3.5.9 Skin Menu ________________________________________________________24
3.6 Report Formatting and Setup__________________________________________24
3.7 User Information ___________________________________________________25
3.7.1 Machine ID _______________________________________________________25
3.7.2 Receipt Header ____________________________________________________25
3.7.3 S/W Version ______________________________________________________25
3.7.4 Factory Default Setting ______________________________________________26
3.8 Setting Hotkeys ____________________________________________________26
3.9 Dust Cover Menu/Control ____________________________________________26
4. OPTIONAL FEATURES
4.1 [STRAP]: Zero Count at Strap _________________________________________27
4.2 Barcode Scanning Mode_____________________________________________27
4.3 Barcode and Cash Concurrent Scanning_________________________________27
4.4 Using Serial Number Mode___________________________________________28
4.5 Multi-Currency Software _____________________________________________28
5. ERROR MESSAGES
6. MAINTENANCE, CONTACTS AND SPECIFICATIONS
6.1 Maintenance and Cleaning ___________________________________________29
6.2 Contact Information _________________________________________________30
6.3 Cassida Pro Series Zeus Specications __________________________________30

3
STRAP — preset selection key for strapping quantities
MODE — counting mode selection key: MIX/ORT/CNT/SORT
REPRT
CC: Current Count of bills - or strap
MIX/ORT/CNT/SORT
4. Total number counted
5
6.
7.
9.
8. Strap: Selected strap quantity
$0
REPRT
CC
STRAPSORT
4
5 6 7 8 9
4. GT (Grand Total) key: Press to
access grand total counting report
5. Total indicates result for counted bills
(total number and total value)
6. Print Key: Press to print count results
7. REPRT Key: Press to access reject
report detail
1.4 Control Panel
4
CONTROL PANEL
Key Function
[C] Clear key; clear errors, counted result and escapes from menu
[START/STOP] [START/STOP] operation key
Function Keys (-) Menu navigation
[CUR], [+GT] or [EXIT] In counting screen, press [CUR] to select a currency (if present)
In count detail screen, push [+GT] to add to and display
grand total
In mode and menu screens, push [EXIT] return to previous screen
[MODE] or ▲ In counting screen or count detail screen, press [MODE] to select
a counting mode: MIX/SORT/CNT/FACE/ORT/VSORT
In currency or mode screens, press ▲to move the selection
cursor up
[REPRT], [REJCT] or ▼In counting screen press [REPRT] to access a detailed report of
counted bills
In count detail screen, press [REJCT] to see a detailed report of
rejected bills
In currency or mode screens, press ▼to move the selection
cursor down
[MENU], [PRINT],
[SET]
In counting screen press [MENU] to access machine settings
In count detail screen, press [PRINT] to print the detailed report
In currency or mode screens, press [SET] to select a setting
[ADD] [ADD] function key / press and hold for space key
[STRAP] Preset selection key for STRAP settings

2.2 Loading Bills
Before loading bills into the Zeus, ensure the desired currency and operation
modes are selected. Proper placement of bills into the hopper reduces feed errors,
jamming, and identication reject errors caused by misaligned bills. Bills should be
stacked neatly prior to loading, and placed between the hopper bill guides at the
center of the hopper.
Avoid counting bills that are wet, excessively dirty, folded, curled, or otherwise
misshapen. Ensure no objects are present in the bills being loaded, including coins,
paper clips, rubber bands, or other foreign materials. These objects will damage the
Zeus and cause failures.
To Reduce Rejects:
• Place the bills evenly arranged as shown below.
• Adjust bill guides to t to the size of the bills.
• Correct the bills if they are severely wrinkled or damaged.
2.3 Counting Modes
There are 7 counting modes
available on the Zeus:
Toggle between the
modes by pressing the
▲ / ▼ keys. Press the
[SET] key to select the
desired mode.
2.3.1 [MIX]: MIX Mode
MIX mode is the default sorting mode for the Zeus. MIX mode counts a stack of mixed
bills regardless of denomination changes, and sums the total while applying all selected
counterfeit detection features. After running a mixed stack of denominations, the Zeus
will display the dollar amount total, and the number of bills counted. In this mode, only
suspect bills or error bills will be rejected. No sorting will occur. Only counterfeit suspects
or notes unreadable due to condition are sent to the reject pocket. When a counterfeit
suspect is sent to reject, the system will beep, and the reject LED bar will be blinking until
the reject pocket is emptied. For per-denomination detail and rejects report, press the
[REPRT] key on the main menu.
Detailed Report Screen Main View Screen
1 Skew
2 Double
3 Suspect
3 Rejects
$1410
REPRT
CC
STRAPMIX
58
58
$120
REPRT
CC
STRAP
6
Total count
of banknotes
6
PCS
$0
REPRT
CC
STRAP
58
Total count
of banknotes
Does not
increment
58
CNT
PCS
$0
REPRT
CC
STRAP
58
Count
of banknotes
in current batch
Does not
increment
234
Cumulative
count of banknotes
ON
CNT
SORT
If any bills were rejected, they will be sent to the reject pocket. To access information
regarding rejected bills, press the [REJCT] key.
7 8
MIX
MIX mode
FACE
FACE mode
SORT
SORT mode
ORT
ORIENTATION mode
CNT
COUNT mode
10$5
VSORT
VALUSORT mode
REPRT
SRL
SERIAL mode
1 2 3 4

2.3.2 [SORT]: SORT Mode
Sort mode is intended to sort out a single
denomination from a mixed stack of bills while
running all selected counterfeit detection features.
This mode is also used for ‘rogue’ or ‘stranger’
checking in a stack of bills intended to be of
the same denomination. All bills of the selected
denomination will pass to the stacker. All other
denominations and any error or suspect bills will
not be counted and will be rejected. When a
counterfeit suspect is sent to reject, the system
will beep, and the reject LED bar will be blinking
until the reject pocket is emptied.
Sort mode defaults to [1] FIRST BILL THROUGH as the denomination of choice.
The rst bill placed in the stacker will be recognized by the Zeus and set as the
denomination to send to the stacker. By clearing the stacker and hopper, the Zeus
will reset the rst bill through to the next stack. This allows for quick sorting of mixed
stacks without having to choose each denomination manually. Alternatively, user can
select a specic denomination, Face or Orientation if the “Sort by Denomination” is
turned on in the settings.
After running a stack of bills the Zeus will display the dollar amount total, and the
number of bills counted. For per-denomination detail and rejects report, press the
[REPRT] key on the main menu.
2.3.3 [CNT]: COUNT Mode
Count mode is intended to count the number of physical pieces placed in the
hopper. In this mode counterfeit detection is disabled. Only the count [CC] and the
number of pieces [PCS] will update. This mode may be used to count the number
of pieces of any article that will pass through the Zeus, including tickets, tags,
barcodes, papers, etc. and no bills will be rejected unless a physical counting error
occurs (DOUBLE, CHAIN, etc.)
2.3.4 [FACE]: FACE Mode
Face mode is used to sort a stack of mixed orientation bills to all face up or face down
which is determined by the rst bill placed in the hopper. This mode will not account for
rotation of the bill, but will retain all enabled counterfeit detection features. Mixed or
sorted bills will pass to the stacker regardless of denomination. All bills which are opposite
facing compared to the rst bill through will be rejected, as well as any recognition errors,
or suspected counterfeit bills. When a counterfeit suspect is sent to reject, the system
will beep, and the reject LED bar will be blinking until the reject pocket is emptied. After
running a stack of bills, the Zeus will display the dollar amount total, and the number of
bills counted. For per-denomination detail and rejects report, press the [REPRT] key on
the main menu.
2.3.5 [ORT]: ORIENTATION Mode
Orientation mode is similar to Face mode in that the Zeus is sorting bills by the physical
orientation each bill is scanned. In orientation mode, the Zeus accounts for all 4 possible
rotations as follows:
1. Face up, reading orientation
2. Face up, upside-down wording
3. Face down, reading orientation
4. Face down, upside-down wording
The orientation being sorted is determined by the orientation of the rst bill placed in the
hopper. All selected counterfeit detection features will remain active during the sorting
process. All bills which are of different orientations compared to the rst bill through
will be rejected, as well as any recognition errors, or suspected counterfeit bills. When
a counterfeit suspect is sent to reject, the system will beep, and the reject LED bar will
be blinking until the reject pocket is emptied. After running a stack of bills the Zeus will
display the dollar amount total, and the number of bills counted. For per-denomination
detail and rejects report, press the [REPRT] key on the main menu.
910
1 Skew
2 Double
3 Suspect
3 Rejects
$1410
REPRT
CC
STRAPMIX
58
58
$120
REPRT
CC
STRAP
6
Total count
of banknotes
6
PCS
$0
REPRT
CC
STRAP
58
Total count
of banknotes
Does not
increment
58
CNT
PCS
$0
REPRT
CC
STRAP
58
Count
of banknotes
in current batch
Does not
increment
234
Cumulative
count of banknotes
ON
CNT
SORT

STRAP SETTINGS
1 100
2 50
3 25
4 20
5 10
6 OFF
7 ENTER STRAP NUMBER
8 ENTER STRAP $ AMOUNT
9 DENOMINATION STRAP

2.5.1 STRAP by Number
This option performs identical to the base strapping function. This sub-menu allows
the user to choose non-standard strap bill counts between 1 and maximum stacker
capacity (150 by default, 200 maximum).
2.5.2 STRAP by Amount
This option allows the user to set a strap to a dollar amount regardless of the number
of bills in a strap. The only modes enabled with this feature are Mixed mode and Sort
mode. For mixed bills in Mixed mode, the Zeus will add all denominations needed to
create the selected dollar amount and ignore the rest. All bills that did not meet the
strapping requirement will be rejected. Please note that the number of pieces/bills per
strap may vary if different denominations are present.
In sort mode, the Zeus will attempt to make a strap with the specied sorting bill. If the
strap value cannot be reached by the selected sort value available, the Zeus will reject
all remaining bills and ash the “INCOMPLETE STRAP!” message.
2.5.3 STRAP by Denomination
This option allows the user to count a desired number of bills for each denomination
typically used for setting up cashier drawers, tills and registers. To activate, press the
[STRAP] key to enter [STRAP SETTINGS] then select [DENOMINATION STRAP].
2.5.3.2 [STRAP] -> [9] Denomination Strap -> [2] Single
2.6 [REPRT]: Post-Count Summary and Detail
The report screen is used to display details of the counting that has just been completed.
Once bills have been run through the Zeus, the [REPRT] screen is used to view details on
per-denomination breakdown, print the current sum of the most recent run, and display
additional detail in STRAP -> SINGLE and STRAP->MULTIPLE modes.
2.6.1 [+GT]: Add to Grand Total
After a count, press [+GT] on the top right
corner, and Zeus adds the current counting
result to the grand total, and opens the grand
total report screen. If a printer is connected
and automatic printing is selected, the Zeus
will automatically print the receipt of the
current counting results.
• Press the [RESET] key to reset the grand
total to zero.
• Press the [PRINT] key to print the grand
total report.
• To exit from the grand total window, press
[C] or place bills on the hopper to start a
new count.
13 14
Choosing MULTIPLE allows all denominations to enter the stacker at once. When this mode is
chosen, the user will be presented with a menu and a list of denominations. Select the number
of bills of each denomination desired in the strap. In this mode, a mixed stack of bills will be
automatically sorted into a single strap of mixed bills to reach the total number of each bill
count selected. Once a strap target value has been reached, the Zeus will send an audible
alert and display an on-screen message that the strap is completed. This mode is typically
used to quickly strap multiple denominations concurrently. All bills which are not specied for
the current strap will be rejected.
Choosing SINGLE allows the user to sort a stack of mixed bills into a straps of single
denominations. All bills not dened in the strap will be rejected. All bills dened in the
denomination menu will be passed to the stacker. When the Zeus senses a difference in
denomination that is dened in the strap, one bill of the new denomination will be passed into
the stacker, the Zeus will beep and display the “DIFFERENT DENOMINATION” message. The
user is to remove the bills in the stacker, remove the top bill, and place each denomination
in its own stack. When a strap of the single denomination is completed, the Zeus will beep
and display a message that the strap is completed. The user will then set aside the complete
strap and begin another of the same denomination. This mode is used to sort a mixed stack of
bills into multiple straps of a single denomination in one pass, instead of sorting bills by each
denomination, then strapping.
2.5.3.1 [STRAP] -> [9] Denomination Strap -> [1] Multiple

MENU SETTINGS AND DESCRIPTIONS
3.
3.1 Auto/Manual Start
This feature allows user to set how the Zeus will operate once currency is placed in the
hopper. The Zeus is preset to [2] AUTO START which means that once the currency is
placed in the hopper, the Zeus will start counting immediately. If [1] MANUAL START
is selected, then user will need to press [START/STOP] button to initiate operation.
3.2 Speed
This feature allows the user to choose the
speed setting the Zeus will operate. The Zeus
is default to count 1000 notes per minute. User
has the ability to select between 800 notes per
min or 1000 notes per min.
2.6.2 [PRINT]: Print Totals Function
From the report menu, press the [PRINT] key to to print out a receipt of the totals from
the most recent count.
2.6.3 [REJCT]: View Reject Report and Reasons
To access information about any rejected banknote, from the COUNT DETAIL screen,
press [REJCT] key to view the detailed reject report. This report contains information
from the most recent count including reject reason, and the numerical order in which
bills were rejected. If STRAP->SINGLE or STRAP->MULTIPLE have been enabled, the
count detail screen will display the [DENOM] button in place of the [REJCT] button. To
access the reject report, enter the [DENOM] menu and then enter the [REJCT] button.
2.7 Manual Entry of Rejected Bills to Count and Total
If unt or known genuine bills continuously pass to the reject pocket - the following
procedure is available to manually add the rejecting bill to the count and sum of the
total count. Following a count that has rejected bills, remove rejected bills from the reject
pocket and place with bills from the stacker.
Press [0] to open the MANUAL ENTRY window. Fill in the elds for each rejected bill
by denomination, and press [DONE] when completed. Note that the CC and sum have
been updated with the manual entries. The printed report will show the manual entered
items on a separate line underneath the actual counting report.
15 16
MENU
1 AUTO/MANUAL START
2 SPEED
3 MODE ENABLE/DISABLE
4 COUNTERFEIT SETTINGS
5 SETTINGS
6 REPORTS
7 USER INFORMATION
8 DUST COVER CONTROL
AUTO/MANUAL START
1 MANUAL START
2 AUTO START

CF SETTINGS
1 MAGNETIC (MG)
2 INFRARED (IR)
3 ULTRAVIOLET (UV)
4 CF SETTINGS ALL ON
5 CF SETTINGS ALL OFF
CFCF
MODE ENABLE/DISABLE
1 MIX ON
2 SORT by denom. ON
3 COUNT (CNT) ON
4 FACE ON
5 ORIENTATION (ORT) ON
6 VALUSORT
7 BARCODE ONLY
8 BARCODE+CASH

3.5.2 Print/Interface/Beep
This menu is intended to allow connection to many third party printers by allowing
customization of the printing interface and data format. Standard receipt printers
typically require setup of the serial interface as specied by the printer manufacturer.
The below list of options provides access to common serial connection setup:
[1] Set BAUD RATE - from [1] 4800 to [7] 115200 (default 9600)
[2] Set DATA BIT - from [1] 5 to [4] 8 (default 8)
[3] Set STOP BIT - [1] 1 or [2] 2 (default 1)
[4] Set PARITY - [1] NONE,[2] ODD or [3] EVEN (default NONE)
[5] Set BEEP - [1] ON or [2] OFF (default ON)
[6] PRINTING SETUP
Options are also available to customize the way the printer functions with the following:
[1] AUTO PRINT (default OFF)
[2] PRINTER AUTO CUT (default OFF)
[3] AUTO PRINT IN GT (default ON)
[4] RESERVED (for future use)
[5] RESERVED (for future use)
[6] SIGNATURE LINE (default ON)
3.5.3 Thousands Separator
Depending on application and region, the user
is able to customize the thousands separator
by choosing to employ a comma as the
separator [1] [,] ex123,456 or a period as
the separator by choosing [2] [.] ex123.456
19 20
PRINT/INTERFACE/BEEP
1 BAUD RATE
2 DATA BIT
3 STOP BIT
4 PARITY
5 BEEP
6 PRINTING SETUP
PRINTING SETUP
1 AUTO PRINT
2 PRINTER AUTO CUT
3 AUTO PRINT IN GT
4 RESERVED
5 RESERVED
6 SIGNATURE LINE 1 (default ON)
7 SIGNATURE LINE 2 (default OFF)
8 COLUMN WIDTH (default 32)

3.5.4 Maintenance Reminder
The Zeus features an automatic service and maintenance reminder that may be
used to schedule regular maintenance. Use the following menu options to set a
maintenance schedule by various methods. Due to the wide range of applications of
the Zeus, multiple selections are available based on use case and service contracts.
[1] SET NUMBER OF DAYS - Reminder
that maintenance is due the number of
days entered from today.
[2] SET NUMBER OF BILLS - Reminder
that maintenance is due when the
number of bills entered is counted
through the unit.
[3] RESET
[4] OFF (default)
[5] CLEANING
NOTE: The Zeus Cleaning Mode allows the user to run a CleanBill Pro Card (or
other currency counter cleaning card) several times through the unit. This
helps to keep the rollers through the bill path in good condition.
To use, select Cleaning Mode and press Set softkey. When prompted,
place CleanBill Pro Card on hopper as you would a banknote. The unit will
alternate between sending the card to the reject pocket and the stacker
pocket. Continue placing the same cleaning card on the hopper until the
unit reaches the count of 10.
Note that if any error occurs (card is skewed or bent and becomes jammed
in unit), the unit will direct you to clear the error and press C. In this case
you will have to re-enter the Cleaning Mode and restart the cleaning count.
3.5.5 Language
This feature allows the user to select
the preferred language for on-screen
communication. English is the
default language.
3.5.6 Clear Remote Count
The Zeus has the capability to connect to an external display. This feature allows the
user to dene how the external display will clear.
[1] AUTO CLEAR - if selected the external
display will clear all values approximately 3
seconds after the bills are cleared from the
stacker. The counting result on the Zeus main
screen remains until cleared.
[2] CLEAR BY [C] KEY - The counting
result is not cleared on the external display
or on the Zeus screen until the [C] key is
pressed (default).
21 22
MAINTENANCE ALARM
1 SET NUMBER OF DAYS
2 SET NUMBER OF BILLS
3 RESET
4 OFF
5 CLEANING

3.5.7 Pocket Capacity
This feature allows user to set the number of notes the reject pocket and stacker capacity.
If the reject pocket or stacker becomes full, the Zeus will stop and ash either a “REJECT
FULL” or “STACKER FULL” message. Clear the pocket and the Zeus will resume
normal operation.
[1] REJECT - Set the reject pocket
capacity to a custom amount. Use the
number pad to set the reject pocket
capacity to any number between 1 and
100 bills. Suggested ranges are: 10 to 30
for worn bills, 31 to 60 for normal bills and
61 to 100 for new bills. If the pocket
capacity is set too high dependent on the
type of bills being used, there is a risk of
bills being ejected from the reject pocket.
[2] STACKER - Select stacker capacity; 100,
150 or 200 (default = 150)
3.5.8 LAN Setting
The Zeus is equipped with an ethernet port
for network connectivity. To enable network
operation, various settings will need tuning
and testing depending on the network
conguration where the Zeus is installed.
Cassida does not provide networking
solutions at the moment, though an API
manual is available upon request to create
custom third party applications. The following
menu settings are available to setup and test
the network:
23 24
[1] DHCP Toggle - Enable or disable Dynamic Host Conguration Protocol
[2] CLIENT - Congure client settings
[3] SERVER - Congure server IP Address and Port
[4] MAC ADDRESS - View the Zeus MAC Address
[5] HOST NAME - Set the hostname.
NOTE: This value will remain through power off and depleted battery events.
[6] PING TEST - Send pings to test communication
3.5.9 Skin Menu
This feature allows user to select how the
interface is displayed. By default, the Zeus
is set to the [1] DARK SKIN for lower light
environments with high contrast and low eye
strain. The second option listed is the [2]
BRIGHT SKIN for brighter
working conditions.
3.6 Report Formatting and Setup
This feature allows the user to access daily, weekly, and yearly counting reports. In order
to use this function, a FAT32 formatted external storage device such as a ash drive
or hard drive must be connected to the USB port on the back of the unit. The external
storage device must be present during all counting and data collection in order for the
reports to be correctly stored. It is recommended that a dedicated storage device is
paired with each Zeus tool that requires reporting.Reporting intervals are dened as [1]
DAILY REPORT, [2] WEEKLY REPORT, or [3] MONTHLY REPORT.

For a DAILY REPORT, choose a date within the last 30 days to run the report and
press [ENTER] once the desired date is highlighted. This will display the report
contents and present the option to print the report using the [PRINT] key. Similarly
for weekly and monthly reports, select the preferred end date for the report or
month to view.
3.7 User Information
The user information screen displays and allows editing of common user features
and unit specic information.
3.7.1 Machine ID
The MACHINE ID is the custom name given to the unit if desired. By default, all
units are set to “ZEUS”. This eld is identical to the HOST NAME as used in the
networking screens, and may be used for network identication. Once this value is
set, it is stored in a special memory that will retain this value through power cycling,
unplugging, and battery depletion.
3.7.2 Receipt Header
This menu provide options to customize what is printed on receipts from the Zeus.
Fields included are NAME, ADDR, TEL, and FAX. If these values are set, every
receipt printed by the Zeus will contain this information at the top of the print.
Follow on-screen instructions for typing and saving these values.
3.7.3 S/W Version
Access this menu to view the current software version, UI version, and further
detailed information about the unit.
25 26
3.7.4 Factory Default Set
Once selected and conrmed, this action returns the Zeus to default factory settings.
3.8 Setting Hotkeys
Up to three user preferences, or hotkeys, can be saved. Hotkeys load the mode and all
related settings active at the time the user preference was saved to the selected hotkey.
The [4], [5], and [6] keys on the number pad
are hotkeys. To activate a hotkey, from the main
screen, press and hold the [4], [5], or [6] key.
Select [SAVE] to save the current conguration
for future use. To load a user setup, press and
hold the desired hotkey and select [LOAD]
to load a saved conguration. The saved
conguration will load automatically.
WARNING
Reseting to factory default will erase any customized
Hot-Keys and other settings made to the machine.
3.9 Dust Cover Menu/Control
Switch on/off dust cover auto closure when the counting starts.
(OFF = banknote processing will start with open dust cover).
HOT KEY (4)
Press [SAVE] to save current
configuration or press [LOAD] to
recall saved configuration
SAVE
LOAD

OPTIONAL FEATURES
4.
4.1 Zero Count at Strap
This function can be activated by a Zeus service provider. Once activated, this
function works with all strapping functions. Zero Count at Strap engages when the
user enables strapping. Once a strap is complete and bills are removed from the
stacker, the on-screen value, piece count, and strap counts will return to zero. This
function also works with ADD, enabling the user to count multiple stacks of bills, while
keeping track of the total number of bills and value of bills counted.
4.2 Barcode Scanning Mode
This mode is used to count barcoded tickets. Tickets are placed into the hopper with
the barcode facing down. During processing, only the number of tickets is counted.
Counterfeit detection is disabled for ticket counting and Barcode mode. The screen
will display the number of processed tickets under CURRENT COUNT (CC) and the
value will remain “0.”
Barcode data may be printed for further records. If the auto print function is enabled,
the data will print automatically as soon as the tickets are removed from the stacker,
or after the stacker capacity has been reached. Processing is interrupted by the
“PRINTING” message.
If auto print is disabled, the warning will display asking the operator to print the
barcode data.
4.3 Barcode and Cash Concurrent Scanning
This mode is used to count mixed barcoded tickets and bills simultaneously. Tickets
must be placed into hopper with the barcode facing down; bills may be placed in any
orientation. All tickets and bills will be passed into stacker. The screen will display the
total number of processed tickets, the total value of counted bills, and the bill count.
During ticket processing, bar code data is collected and can be printed for a physical
record. Is the AUTO PRINT function is enabled, the data will print automatically as
soon as bills and tickets are removed from the stacker, or after the stacker capacity
has been reached. Processing is interrupted by the “PRINTING” message.
If auto print is disabled, the warning will display asking the operator to print the
barcode data.
4.4 Using Serial Number Mode
Two options are available for capturing serial numbers: saving the data to an
external storage device, or printing the numbers directly. To count to external
storage, insert the device into the USB-A port on the back of the unit prior to power
on, then turn on the unit and operate as normal. To connect to a printer for serial
capture, turn on the unit with the printer turned off. Upon completion of the Zeus
self-test (rollers turn, and then main menu is displayed) power on the printer.
To use Serial Number Mode, all bills must be facing the same orientation and be
placed face down in the hopper. It is suggested the user runs the stack of bills to be
scanned in FACE mode and ORT mode prior to attempting serial capture to verify
the orientation. Any incorrectly oriented bills will be rejected. Place bills face down
in the hopper. The Zeus will count the bills as normal (pieces and sum) and tally on
screen. To send the captured serial data to the external storage or printer, press the
[PRINT] key.
To view the captured serial number information on a computer, remove the external
storage media from the Zeus and plug into a computer. In the root folder of the
device, a new folder has been created titled “Serial Number Data”. This directory
contains the serial information in a folder titled with the date and count, followed
with a count sequence number, and nally and .XML le and images of the serial
numbers in .bmp format.
4.5 Multi-Currency Software
The Zeus is equipped with the option to count various worldwide currencies upon
request. Please contact CassidaPro for more information on how to use the Zeus
with international or multiple currencies.
27 28

ERROR MESSAGES
5.
Error message Reject Reason
SUSPECT IR Unrecognized or missing expected anti-counterfeit infrared
features. May be due to marked, taped, or stained currency
SUSPECT MR Unrecognized or missing expected anti-counterfeit magnetic
features. May be due to wrinkling or wear on notes
SUSPECT UV Unrecognized or missing expected anti-counterfeit ultraviolet
features. May be due to marked or stained currency
ID ERROR Unable to recognize bill as selected currency type
DIFF Different denomination
CHAIN Bills fed too close to each other in transport path
DOUBLE Two or more bills passed together, thickness out of range for
expected currency
HALF Half note detected, typically torn or folded bills
SKEW Bills misaligned through transport path
SRL MISMATCH Serial numbers of the bill did not match
NO SRL No serial number found on the bill. Can occur if bills are
placed onto hopper face up
Error message Solution
JAM1 Open the upper door and remove the bills from the bill path.
Close the door and Press [C]
JAM2 Open the lower door and remove the bills from the bill path.
Close the door and Press [C]
FEED ERROR Remove the bills on the hopper. Adjust the gap if it is too tight.
Place the bills again
MOTOR ERROR Open the upper and the lower doors, remove all the bills from
the bill path. Turn the power off and on and check if the motor
runs. If not, consult with a service provider
DIVERTER ERROR Check if a bill is jammed around the diverter. Test the diverter
counting mixed denominations in ORT mode. If all bills are
directed to the stacker or the reject pocket, consult with your
service provider
UPPER DOOR OPEN Close the upper door
LOWER DOOR OPEN Close the lower door
CLEAR STACKER Remove the bills from the stacker. Also make sure the clear
sensor windows in the pocket are clear of dust and debris
CLEAR REJECT Remove the bills from the reject pocket
CLEAR HOPPER Remove the bills from the hopper
CHECK PS1 Check if the upper door is open or if a bill is in the bill path
CHECK PS2 Check if the lower door is open or if a bill is in the bill path
29 30