CBM SST 1700B Instruction sheet

Rev. 00 – 06/08/2014 Installazione SST1700-2200 r0 EN.DOC pag. 1 di 4
Steam sterilizer
SST 1700B - SST 2200B
INSTALLATION
and FIRST USE
The equipment has already been tested on the production site
and it is ready to be used
IT DOES NOT NEED TESTING DURING INSTALLATION

C.B.M. S.r.l. a socio unico - Medical Equipment –
Via Castello 10, 26038 Torre dé Picenardi (CR) - Italy
Rev. 00 – 06/08/2014 Installazione SST1700-2200 r0 EN.DOC pag. 2 di 4
INSTALLATION
1. Unpack the machine and preserve the original package which shall be used for any
returns or repairs., place the appliance on a stable surface capable of supporting at
least 70 Kg.
2. VENTILATION: In the case the sterilizer should be placed close to walls or be fitted-in,
ensure observance of the minimum ventilation dimensions, i.e. at least 5cm of space all
round to allow air circulation around the machine.
3. Check that the appliance is positioned slightly inclined towards the back. To this end,
pour a small quantity of water (10cc) in the chamber and ensure it flows towards the
bottom.
Should the inclination need to be changed, regulate the adjustable feet.
Connect the power cable located at the back of the appliance, open the cover below the
front display and press the green power switch.
The appliance must be connected to a grounded mains socket in compliance with IEC
Standards, with a mains voltage of 230 Volts and minimum capacity of 16 Amps.
WARNING!!
♦Do not connect other appliances to the same socket.
♦Should it be necessary to use an adapter, ensure its capacity is higher than the
maximum sterilizer power ( 2,090 watts).
4. Switch on the main green switch located under the cover
below the touch-screen display
5. The display shows a short self test

C.B.M. S.r.l. a socio unico - Medical Equipment –
Via Castello 10, 26038 Torre dé Picenardi (CR) - Italy
Rev. 00 – 06/08/2014 Installazione SST1700-2200 r0 EN.DOC pag. 3 di 4
OPEN DOOR
Open the door by pressing the OPEN DOOR key
Remove from the chamber the given accessory
FILL CLEAN WATER
1. Provide for a container with at least 3 litres of DEMINERALIZED water, see also the
table on User Manual
WARNING: the use of ordinary water causes damages and malfunctions of the
appliance in a short time and invalidates its warranty.
2. Fit the appropriate hosepipe (supplied) by pressing the pipe-fitting onto the blue/white
“Fill Clean Water Tank” coupling on the left.
3. Place the other end of the hosepipe in the demineralized water making sure it touches
the bottom.
4. Press the Right direction key on the display then press the Fill WATER key.
5. The tank holds a maximum of 3 litres of water; when the tank is full, FILLING will stop
automatically.
Should water in the container finish before the tank is full, please press the STOP key
on the display.
6. When loading is completed the display shows the operation end, press STOP and ESC
to go back to the main pages
7. Disconnect the hosepipe by pressing the Blue button on the pipe-fitting and pulling the
coupling slightly.

C.B.M. S.r.l. a socio unico - Medical Equipment –
Via Castello 10, 26038 Torre dé Picenardi (CR) - Italy
Rev. 00 – 06/08/2014 Installazione SST1700-2200 r0 EN.DOC pag. 4 di 4
STERILIZATION CYCLE
1. After having introduced the material to be sterilized in the chamber, close the door to its
limit, then press the DOOR LOCK key, the icon DOOR LOCKED will appear on
the display
2. Select the desired cycle by pressing the relevant icon (example ), see also the
cycles Table on the User manual.
3. Press the DRYING key and select the drying cycle desired, also shown in the
information bar.
4. After having selected the DRYING cycle, press the START key.
5. From this moment the door is fully locked and the appliance operates automatically until
the end of the cycle.
6. If the cycle is completed successfully the appliance warns of the END of cycle through
sound impulses and the writing CYCLE COMPLETED on the display.
7. Upon completion of the cycle press the ENTER key. It is now possible to open
the door by pressing the OPEN DOOR key.
8. Remove the material inside the chamber
Make attention to the hot temperature