CDP CDP-001F User manual

1 of 9
MANUAL
Drowsiness and Distraction Detector
CDP-001F
C.D.Products S.A.

2 of 9
1. Product description
1.1 Introduction
This advanced fatigue and distraction digital detector can prevent serious driving accidents.
This device constantly monitors all facial gestures of the driver. Through a complex facial
recognition algorithm, it detects signs of tiredness, drowsiness or distractions, even with the
use of sunglasses or at night.
The drowsiness and distraction monitor CDP-001F is a simple and effective detection device
that identifies danger immediately. Warnings include powerful sound alerts and LED lights.
With this real-time driving monitoring system you can prevent serious traffic accidents.
According to a DGT (National Department of Traffic) report, distractions behind the
wheel cause one in three fatal accidents.
It is especially suitable for all types of drivers, especially people with high risk exposure due
to fatigue or distractions while driving.
1.2 Accessories
List of Accessories
S / N Part name Quantity
①Device 1 PC
②Car charging cable 1 PC
③User manual 1 PC
★Carefully check that all parts are in the box. If any are missing, please contact the seller.
★In order to understand the installation and use of this device, read this manual carefully.
C.D.Products S.A.

3 of 9
2. Specifications and features
2.1 Product appearance and interface description
1. Camera (with front view and adjustable angle)
2. Warning indicator light
3. Power indicator light
4. Speaker
5. USB, power connector
2.2 Product Specifications
Specification Standard Operating range
Voltage 5V 4.75 ~ 5.25V
Consumption 0.4 A 0,4 ~ 0.5A
Adapter 12V / 24V 9 ~ 30V
Adapter current 1A
Dimension 88 * 88 * 48 mm
Power key N / A
On/Off signs V sign: Turns off
(red light turns off)
Open palm: Turns
on (red light turns
on)
LED indicator Flashing bright red:
Alarm Indicator Green indicator: Ready
Power supply
connector Micro-USB
Temperature -20 ~ 70℃
2.3 Main features
Functional day or night
Switch using gestures
Led indicators
Adjustable camera angle
Contactless design
C.D.Products S.A.

4 of 9
3. Description of features
3.1 Alarm function
Inspection Description Sound
Closing eye (according
to The P80 standard)
Device alerts when it
detects that the driver
closes his eyes.
Beep
sound 1
Closing eye with UV
sunglasses
Device alerts when it
detects that the driver
closes his eyes.
Beep
sound 1
Yawning Device alerts when it detects that the driver
yawns.
Beep
sound 2
Nodding off Device alerts when it detects that the driver is
nodding off. Slow beep
V sign The device is deactivated when the driver makes a V
sign with his hand. Short tone
Open palm gesture
The device is activated
when the driver makes an
open palm gesture with his
hand.
Ready
voice
3.2 Operation of LEDs status
Green LED on: Power on.
Red LED on: Alarm sounds activated.
Red LED off: Alarm sounds off.
Red LED flashing: Closing eyes, yawning or nodding off detected.
C.D.Products S.A.

5 of 9
4. Installation and test
Select the placement of the device according to the driver's height and posture.
Perform the tests in section 4.2 before attaching it to the dashboard.
It is very important a good placement for proper operation, test at various sites and
distances until you find the best location for your vehicle.
4.1 Installation and tests
(1) Connect the micro USB charging port of the device to the car using the charging cable.
(2) Adjust the position of the seat as shown in Photo 4-1, leaving it a distance of 50 ~ 90 cm
from your face. Check that there are no obstacles between the driver and the device.
The better distances around 80 cm in ours test.
(3) Adjust the horizontal position of the camera with your head in front of it, as shown in Photo 4-
2.
(4) Adjust the vertical angle of the camera to capture your face.
(5) Connect the camera, close your eyes for 1 second, yawn or nod off to check its
functions. Then, remove the protective film from the non-slip mat and attach the device.
(If the anti-slip mat loses adhesion, you can clean it with water, wait for it to dry and it will
work again).
(6) The charging cable can be installed and set according to the actual placement.
Image 4-1 Image 4-2
C.D.Products S.A.

6 of 9
Example in a Toyota Land Cruiser and BMW series 5
4.2 Testing the alarm function
(1) Start-up test: Connect the device. After a few seconds you will hear "Ready" and the green
and red LEDs will remain on. This means that the device has been successfully activated
(2) Closing eyes test: Close your eyes for about 1-2 seconds, and you'll hear a beep sound.
This sound indicates that the alarm is operating correctly.
(3) Yawning test: Open your mouth as if you were yawning for about 1-2 seconds. You'll hear a
beep sound. This indicates that the alarm works correctly.
(4) Nodding off test: Nod off slightly for about 1-2 seconds. You'll hear a beep sound, indicating
that the alarm works correctly.
(5) V sign test: Face the camera and make a V sign for more than 3 seconds (V-shaped hand
gesture as shown in photo 4-3). Place your hand next to your head at eye level. (This gesture
might not be recognized at night or in very strong sunlight.) You will hear a beep sound and
the red light will turn off while deactivating the alarms.
(1) Image
4-3
(2) Image
4-4
(6) Open palm test: Raise your open palm (as shown in photo 4-4) for about 3.5 seconds. Place
your hand next to your head at eye level. (This gesture might not be recognized at night or in
very strong sunlight.) If you hear a short "Ready", it means that the device has recognized
the palm gesture as normal and it has been activated.
* You can watch an explanatory video of these tests on our website www.cdpsa.eu
C.D.Products S.A.

7 of 9
5. Attention
1. Make sure the device does not interfere with the driver's field of vision.
2. When wearing anti-infrared sunglasses, with IR cut or overly opaque lens, the device will
not be able to identify the pupils and it will not work. Normally, the device is capable of
working with category 0, 1, or 2 lens. Performance is greatly affected with category 3
lens, and driving is forbidden with category 4 lens.
•Under normal conditions, an absorption of 60% to 80% is sufficient.
3. The device constantly monitors the driver's fatigue by controlling his facial expression. The
alert cannot be triggered if his eyes cannot be viewed, or if something is worn covering his
face, such as a mask, ski mask, etc.
4. Check that the dashboard is clean and dry before affixing the device in position.
5. Be aware of traffic rules, do not drive if you are feeling fatigued.
6. This product is sensitive to infrared light (such as sunlight), in some specific environments it
can affect identification accuracy.
C.D.Products S.A.

8 of 9
6. Troubleshooting
7.
Problem Possible reason Solution
Does not start The device is turned off. Make sure the power is connected correctly.
No alarm sounds are heard
The red indicator is off.
1. Make an open palm gesture to turn on the
device.
2. Reconnect the device.
The driver's face is not within
the viewing range of the
camera.
Adjust the camera's mounting position or angle.
The camera lens is dirty. Clean the camera lens.
The device works
abnormally. Reconnect the device.
The speaker is faulty. Replace the device.
Stops recognizing the gestures The gesture is outside the
device's identification range. Repeat the gesture in the appropriate position.
It stops working at night The IR is faulty. Replace the device.
7. Important notices
•This product should only be used as a driver assistance system. It can help minimize traffic
accidents caused by fatigue, but it can't prevent traffic accidents. C.D. Products S.A. will in
no case assume responsibility for traffic accidents. Always observe traffic rules and drive
with caution. Take driving breaks and always stay alert behind the wheel.
•Do not hit, drop, or shake the device violently. Use it correctly.
•Do not open or unscrew the device. Only our technical support personnel is authorized and
trained to do so. If you disassemble the device without our authorization, you will
automatically void the warranty.
•Please store this product in a dry environment when not in use.
C.D.Products S.A.

9 of 9
8. Contact data
C.D.PRODUCTS S.A.
Polígono P-29
Calle Kanna, 2 – Local 3
28400 Collado Villalba – Madrid
Customer service: 902 10 40 60
Email: [e-mail]
C.D.Products S.A.