ceepo Stinger User manual

Stinger
2021 Assembly Guide

Stinger
2021 Assembly Guide

Stinger
2021 Assembly Guide
TABLE OF CONTENTS
1. Parts included in the BOX................................4
2. FSA SMR Stem .....................................................5
3. Brake Hose Routing...........................................7
4. Electric Cable Routing & Installation...........8
5. Mechanical Cables Routing SRAM............10
6. Mechanical Cables Routing Shimano .......11
7. Mini-Clamp & Clamp Installation................12

Stinger
2021 Assembly Guide
Headset
FSA No55R 1.5” CR STD
A
Stem & Spacers
FSA SMR Stem, for integration cables
Spacers 1cm X 1pc, 2cm X 2pcs
B
Expander
For ID 23mm fork
C
Mini Clamp
Clamp on the setpost
D
Seat Clamp
E
Cable Guide
For mechanical routing use
F
Alloy Cable Stop
For mechanical routing use
G
Rubber Sleeve
Battery Holder for Shimano Di2
H
Thru Axles
I
C
B G
D
1. Parts included in the BOX
E F
H
A I
4
2021

Stinger
2021 Assembly Guide
2. FSA SMR System
Upper
1-1/2”, 45 °x 45°
Compression Ring
Headset Bearing
Top cap
Cable cover spacer
SMR Stem
Expander
Lower Bearing
1-1/2”, 45 °x 45°
C
B
A
5
2021

Stinger
2021 Assembly Guide
2. FSA SMR System (suite)
Maximum stack
25mm Stem Spacer
+10mm bearing Top cap
+18mm Cable cover spacer
10mm
18mm
5mm
10mm
Two-piece Stem Spacers
allow for installation
or removal without re-cabling
6
2021

Stinger
2021 Assembly Guide
A
3. Brake Hose Routing
Front Brake Hose
A single brake hose can pass through the
fork steerer, so it doesn't require a connector
bushing.
Rear Brake Hose
If the rear brake is on the right hand, route
the hose around the drive side of the fork
inside the headtube.
These routing illustrations are intended as
installation instructions only. For both
hydraulic and mechanical disc brakes, please
refer to that component's website to find
further information.
B
A
B
Chain stay height
25mm
A
B
A
B
7
2021

Stinger
2021 Assembly Guide
Step 1
Secure battery in the Di2 Battery Collar.
Make sure to align the grooves.
Step 2
Insert all cables through the compression
ring opening, and upper bearing and bearing
cap.
Step 3
Install Di2 Junction-A in dropbar.
4. Electric Wire Routing
& Installation
Step 1
Step 2
Step 3
Front Brake Hose
Rear Brake Hose
Di2 Wire
8
2021

Stinger
2021 Assembly Guide
Step 4
Connect the Di2 wires.
4. Electric Wire Routing
& Installation (suite)
Step 4
Di2 Wire
9
2021

Stinger
2021 Assembly Guide
5. Mechanical Cable Routing
& Installation - SRAM
Cable Guide
Step 1
All cables go through the compression ring
opening, the upper bearing and the bearing
cap.
Step 2
Feed the cables through the frame.
For a SRAM front derailleur, there needs to
be an alloy cable stop.
G
F
Alloy Cable Stop
Step 1
Step 2
10
2021

Stinger
2021 Assembly Guide
6. Mechanical Cable Routing
& Installation - Shimano
Cable Guide
Step 1
All cables through the compression ring
opening, and upper bearing and bearing cap.
Step 2
Feed the cables through the frame.
For Shimano groupsets, all mechanical cable
hoses connect directly to the derailleurs.
F
Step 1
Step 2
11
2021

Stinger
2021 Assembly Guide
7. Mini Clamp &
Clamp Installations
The seat post is secured via two clamps.
Mini Clamp
The mini clamp should be mounted on the
seatpost prior to installing the seatpost.
It has two functions:
1. Maintain saddle height
2. Install a race number board
The mini clamps remains on the seatpost
when you remove it.
Clamp
The seat clamp wedge should be placed
inside the frame's clamp pocket after
inserting the seatpost. Make sure you can
access the Allen key bolt head for tightening
(6Nm).
M3, Max Torque 3Nm
D
E
Mini Clamp
M5, Max Torque 6Nm
Clamp
3Nm
6Nm
12
2021