CEL-MAR ADA-13110MG User manual

User manual
ADA-13110MG
RS232 to ETHERNET converter wit MODBUS GATEWAY
1
io_ada-13110mg_v.1.1_en
ADA-13110MG
Copyright © 2001-2020 CEL-MAR sp.j.

Contents
1. ENERAL INFORMATION..................................................................................................................................................................... 4
1.1. WARRANTED INFORMATION...................................................................................................................................................... 4
1.2. ENERAL CONDITIONS FOR SAFE USE................................................................................................................................... 4
1.3. CE LABEL...................................................................................................................................................................................... 4
1.4. ENVIRONMENTAL PRESERVATION........................................................................................................................................... 4
1.5. SERVICE AND MAINTENANCE.................................................................................................................................................... 4
1.6. PACK CONTENTS......................................................................................................................................................................... 4
2. PRODUCT INFORMATION.................................................................................................................................................................... 4
2.1. PROPERTIES................................................................................................................................................................................ 4
2.2. DESCRIPTION............................................................................................................................................................................... 5
2.3. ETHERNET NETWORK COMMUNICATION................................................................................................................................6
2.3.1. TCP/UDP SOCKET MODE COMMUNICATION................................................................................................................... 6
2.3.2. COMMUNICATIONS IN THE VIRTUAL SERIAL PORT MODE (RealPort)..........................................................................6
2.3.3. COMMUNICATIONS IN THE SERIAL BRID E MODE........................................................................................................ 6
2.3.4. COMMUNICATIONS IN THE INDUSTRIAL AUTOMATION MODE (Modbus ateway)......................................................6
2.3.5. OTHER COMMUNICATION TYPES..................................................................................................................................... 6
2.4. ISOLATION.................................................................................................................................................................................... 6
3. INSTALLATION...................................................................................................................................................................................... 6
3.1. ASSEMBLIN ................................................................................................................................................................................ 6
3.2. ETHERNET NETWORK CONNECTION.......................................................................................................................................6
3.2.1. CONNECTIN TO NETWORK ADAPTER OF PC............................................................................................................... 7
3.2.2. CONNECTIN FOR OPERATIN IN REALPORT MODE...................................................................................................7
3.2.3. CONNECTION FOR OPERATIN IN TCP & UDP SERIAL BRID E MODE......................................................................8
3.2.4. CONVERTERS CONNECTION AS MODBUS ATEWAY.................................................................................................10
3.3. RS232 DEVICES CONNECTION TO ADA-13110M .................................................................................................................10
3.3.1. CONNECTIN OF DEVICE WITH RS232 PORT, DTE TYPE (PC COMPUTER).............................................................10
3.3.2. CONNECTIN OF DEVICE WITH RS232 PORT, DCE TYPE (MODEM, CODE READER).............................................11
3.4. POWER SUPPLY CONNECTION............................................................................................................................................... 11
4. ACTIVATION........................................................................................................................................................................................ 11
5. CONFI URATION................................................................................................................................................................................ 11
5.1. INITIAL CONFI URATION USIN ADAFINDER SOFTWARE..................................................................................................12
5.1.1. ADAFINDER INSTALLATION.............................................................................................................................................12
5.1.2. NETWORK SETTIN ......................................................................................................................................................... 12
5.2. CONFI URATION AND MANA EMENT BY THE USE OF INTERNET BROWSER.................................................................13
5.2.1. NETWORK CONFI URATION........................................................................................................................................... 14
5.2.2. SERIAL PORT CONFI URATION......................................................................................................................................14
5.2.2.1. SERIAL PORT PROFILE CONFI URATION (OPERATIN MODE)........................................................................14
5.2.2.1.1. REALPORT (VIRTUAL PORT) CONFI URATION...........................................................................................15
5.2.2.1.2. TCP SOCKETS CONFI URATION...................................................................................................................15
5.2.2.1.2.1. TCP SERVER & CLIENT CONFI URATION...........................................................................................15
5.2.2.1.2.2. THE 'ENABLE TCP KEEP-ALIVE' OPTION CONFI URATION..............................................................16
5.2.2.1.2.3. SERIAL PORT TRANSMISSION PARAMETERS CONFI URATION.....................................................17
5.2.2.1.3. UDP SOCKETS CONFI URATION.................................................................................................................. 17
5.2.2.1.3.1. UDP CLIENT & SERVER CONFI URATION IN CASE OF MASTER DEVICE.......................................17
5.2.2.1.3.2. UDP CLIENT & SERVER CONFI URATION IN CASE OF SLAVE DEVICE..........................................18
5.2.2.1.3.3. SERIAL PORT TRANSMISSION PARAMETERS CONFI URATION.....................................................18
5.2.2.1.4. SERIAL BRID E PROFILE CONFI URATION................................................................................................19
5.2.2.1.4.1. SERIAL PORT TRANSMISSION PARAMETERS CONFI URATION.....................................................19
5.2.2.1.5. INDUSTRIAL AUTOMATION (MODBUS ATEWAY) CONFI URATION.......................................................19
5.2.2.1.5.1. CONFI URATION FOR COMMUNICATION WITH DEVICES MODBUS-MASTER TYPE....................19
5.2.2.1.5.2. CONFI URATION FOR COMMUNICATION WITH MODBUS-SLAVE TYPE DEVICE...........................21
5.2.2.1.5.3. SERIAL PORT TRANSMISSION PARAMETERS....................................................................................23
5.2.3. SYSTEM SETTIN S........................................................................................................................................................... 23
5.2.4. USERS CONFI URATION................................................................................................................................................. 23
5.2.4.1. CHAN IN USER MANE AND PASSWORD............................................................................................................23
5.2.4.2. ADDIN NEW USER WITH LIMITED PERMISSIONS FOR CONFI URATION OR MANA EMENT.....................23
5.2.5. MANA EMENT................................................................................................................................................................... 24
5.2.5.1. SERIAL PORTS MANA EMENT...............................................................................................................................24
5.2.5.2. CONNECTIONS MANA EMENT...............................................................................................................................24
5.2.6. ADMINISTRATION.............................................................................................................................................................. 24
5.2.6.1. FILE MANA EMENT................................................................................................................................................. 24
5.2.6.2. BACKUP & RESTORE CONFI URATION................................................................................................................ 24
5.2.6.3. FIRMWARE UPDATE................................................................................................................................................. 24
5.2.6.4. FACTORY DEFAULT SETTIN S.............................................................................................................................. 24
5.2.6.5. SYSTEM INFORMATION...........................................................................................................................................24
5.2.6.6. REBOOT..................................................................................................................................................................... 24
5.2.6.7. LO OUT – ENDIN MANA EMENT AND CONFI URATION................................................................................24
2
ADA-13110MG

6. USIN VIRTUAL PORT SERVICE [REALPORT]................................................................................................................................ 24
6.1. VIRTUAL PORT DRIVER INSTALLATION IN WINDOWS XP....................................................................................................24
6.2. REALPORT CONFI URATION IN WINDOWS XP.....................................................................................................................25
7. FACTORY DEFAULT........................................................................................................................................................................... 27
8. TROUBLESHOOTIN .......................................................................................................................................................................... 27
9. VERSIONS........................................................................................................................................................................................... 27
10. SPECIFICATION................................................................................................................................................................................ 27
3
ADA-13110MG

1. GENERAL INFORMATION
Thank you for your purchase of CEL-MAR Company product. This product has been completely tested and is covered by a two year
warranty on parts and operation from date of sale.
If any questions or problems arise during installation or use of this product, please do not hesitate to contact Technical Support at +48
41 362-12-46 or e-mail [e-mail].
1.1. WARRANTED INFORMATION
ADA-13110MG converter is covered by a two year warranty from date of sale. In case of being damaged it will be repair or the
damaged component will be replace. The warranty does not cover damage caused from improper use, materials consumption or any
unauthorized changes. If the product does not function (is damaged), or not operate in accordance with the instructions, will be
repaired or replaced.
All warranty and no warranty repairs must be returned with paid transport and insuring to the CEL-MAR Company.
CEL-MAR Company under no circumstances won't be responsible for ensuing damage from improper using the product or as a result
of random causes: the lightning discharge, the flood, the fire and the like.
CEL-MAR Company is not be held responsible for damages and loss including: loss of profits, loss of data, pecuniary losses ensuing
from using or the impossibility of using this product.
In specific cases CEL-MAR Company discontinue all warranties and in particular do not follow the user manual and do not accept
terms of warranty by the user.
1.2. GENERAL CONDITIONS FOR SAFE USE
The device should be installed in a safe and stable places (eg, electroinstallation cabinet), the powering cable should be arranged so
as not to be exposed to trampling, attaching, or pulling out of the circuit.
Do not put device on the wet surface.
Do not connect devices for nondescript powering sources,
Do not damage or crush powering wires.
Do not make connection with wet hands.
Do not adapt, open or make holes in casings of the device!
Do not immerse device in water or no other liquid.
Do not put the fire opened on device sources: candles, an oil lamps and the like.
Complete disable from the supply network is only after disconnecting the power supply circuit voltage.
Do not carry out the assembly or dis-assembly of the device if it is enabled. This may result to short circuit and damage the device.
The device can not be used for applications that determine human life and health (eg. Medical).
1.3. CE LABEL
The CE symbol on the device CEL-MAR means compatibility with electromagnetic compatibility Electromagnetic
Compatibility Directive EMC 2014/30/WE.
Declaration of Conformity is delivered with purchased converter.
1.4. ENVIRONMENTAL PRESERVATION
This sign on the device inform about putting expended device with other waste materials. Device should send to the
recycling. (In accordance with the act about the Electronic Appliance Expended from day 29 of July 2005)
1.5. SERVICE AND MAINTENANCE
ADA-13110M converter does not require the servicing and maintenance.
Technical support is available at number [phone] in 8.00-16.00, from Monday to Friday or e-mail [e-mail].
1.6. PACK CONTENTS
ADA-13110M converter; User Manual; CE declaration; CD with ADANet software.
2. PRODUCT INFORMATION
2.1. PROPERTIES
●Functioning on ETHERNET network- IEEE 802.3 standard,
●10/100BaseT physical layer,
●Connection Ethernet networks via RJ45 connector
●Baud rate 10/100Mbps (auto-sensing),
●Full or half duplex (auto-sensing) operates mode,
●Protocols: TCP, UDP, DHCP, SNMP, SSL/TLS, Telnet, Rlogin, LPD, HTTP/HTTPS, SMTP, ICMP, I MP, ARP,
●WWW sever implemented for converter configuration,
●Configuration of net services according to user personal setting,
●Static or dynamic IP address (added by DHCP server),
●Diagnostics of serial and network port,
●Encoded transmission: DES (56-bit), 3DES (168-bit), AES (128/256-bit),
●Functioning in modes: virtual serial port, TCP serial bridge, UDP serial bridge, TCP sockets, UDP sockets, MODBUS Data
ateway,
●RS232 interface signals: Rx, Tx, RTS, CTS, DTR, DSR, DCD,
●RS232 baud rate ( bps): 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, 9600, 14400, 19200, 28800, 38400,
57600, 115200, 230400,
4
ADA-13110MG

●RS232 data format - Number of data bits: 5, 6, 7, 8; Parity checking: None, Odd, Even, Constantly 1, Constantly 0; Stop Bits: 1, 2,
●Transparent for all protocols, which the data format is compatible with the above specifications of RS232 interface e.g. MODBUS,
DNP, PROFIBUS and other,
●Integrated protocols converter MODBUS-TCP to MODBUS-RTU/ASCII (MODBUS Data ateway),
●Operating in modes: MODBUS-RTU Master/Slave and MODBUS-ASCII Master/Slave,
●Connection RS-232 network via DSUB-9 Mail connector,
●External power supply 10 - 30 VDC stable min. 3W,
●1kV= or 3kV= galvanic isolation between ETHERNET interface and power supply - depends on version,
●1kV= or 3kV= galvanic isolation between RS232 interface and power supply - depends on version,
●Protection against power supply reverse connection,
●DIN 43880 standard - mounting in typical electro-installation unit,
●Rail mounting according to DIN35 / TS35 standard,
●Dimensions (W x D x H) 53mm x 62mm x 90mm.
2.2. DESCRIPTION
ADA-13110M converter is use for data transmission between devices equip with RS232 interface via LAN/WAN network. Data
transmission takes place without the interference of data format. Operating in ETHERNET network can be in Virtual Serial Port, TCP
serial bridge, UDP serial bridge, TCP sockets, UDP sockets, MODBUS Data ateway. The MODBUS Data ateway converts
MODBUS-RTU master/slave and MODBUS-ASCII master/slave protocol to MODBUS-TCP and inversely. This allows for integrate
MODBUS-RTU/ASCII with MODBUS-TCP devices within one network.
Can be configured and managed via Internet browser – converter has implemented WWW server. ADA-13110M has standard DB-
9M (male) RS232 connector, screw terminal block for connecting the power supply and RJ45 modular connector for ETHERNET
network connection.
The converter transmits data via RS232 interface with maximum baud rate up to 230,4 kbps and uses signals Rx, Tx, RTS, CTS, DTR,
DSR, DCD of RS232 interface.
To the RS232 port of ADA-13110M can be connected to telephone exchanges, barcode scanners, modems, weight, magnetic card
readers. It is adapted for powering from the regular voltage external source which value should contain from 10V to 30V and was
provided from the power pack about 3W power. Converter has implemented protection against opposite polarization of power supply
and over-voltage protection ESD 15kV on RS232 interface lines.
We provide with converter the drivers which installed in the operating systems, will create an additional COM port. This port is the next
free number eg COM3, can be used like a standard COM port. However, it is not the real port existing in a computer, but only a virtual,
created by the system, therefore some programs running under DOS and links to this COM port may not function properly.
Fig. 1. ADA-13110MG view
5
ADA-13110MG
(RS-232)
62mm
53mm
6mm 10mm
90mm
Network activity
transmitting / receiving
Connection activity
81
- +
ACT LINK
(ETH)
RST
V + V -
10 – 30
VDC
ADA-13110MG
RS-232 to ETHERNET
CONVERTER with MODBUS GATEWAY
PWRTXRX
RS-232
DCD DSR DTR CTS RTS

2.3. ETHERNET NETWORK COMMUNICATION
2.3.1. TCP/UDP SOCKET MODE COMMUNICATION
Communication in the mode TCP/UDP sockets allows an application SCADA, MMI e.t.c., to transfer data to the serial port of the
converter via Ethernet network by the use of client and server TCP/UDP services.
2.3.2. COMMUNICATIONS IN THE VIRTUAL SERIAL PORT MODE (RealPort)
Communication in the virtual serial port mode allows an application SCADA, MMI e.t.c., to transfer data to the serial port of the
converter via Ethernet network, by the use virtual COM port , created in an operating system.
2.3.3. COMMUNICATIONS IN THE SERIAL BRIDGE MODE
Communication in the serial bridge mode allows transferring data via Ethernet network between serial port of the converter's ports in
one-to-one topology or one-to-many by the use of client and server TCP/UDP services.
2.3.4. COMMUNICATIONS IN THE INDUSTRIAL AUTOMATION MODE (Modbus Gateway)
Communication in the MODBUS ateway (IA) allows conversion of MODBUS-RTU master/slave protocol and MODBUS-ASCII
master/slave protocol to MODBUS-TCP protocol and inversely. It's let to integrate MODBUS-RTU/ASCII devices with MODBUS-TCP
devices in a single network.
2.3.5. OTHER COMMUNICATION TYPES
ADA-13010M converter can be configured in other communication types, like:
– terminal mode,
– modem emulation mode,
– console mode,
– user mode.
2.4. ISOLATION
Converter ADA-13110M has galvanic isolation, on the level 1kV= or 3kV=, depend on version described in section VERSIONS.
Isolation from the power supply allows transmitting signals: Tx, Rx, RTS, CTS, DTR, DSR, DCD of RS232 interface.
3-way isolation allows transmitting signals: Tx, Rx, RTS of RS232 interface.
Fig. 2. Isolation structure
3. INSTALLATION
This chapter will show how to connect ADA-13110M to RS232 devices, LAN/WAN network and power supply and how to use it.
In the purpose of minimization of disruptions from environment is being recommended to:
●apply multipair type shielded cables, which shield can be connected to the earthing on one end of the cable,
●arrange signal cables in the distance not shorter than 25 cm from powering cables,
●apply cable of adequate cross-section due to voltage drops for converter powering,
●use Interference suppression filters for power supply converters that are installed within a single object.
●not supply converter from power circuit device that generates large impulse interference such as transmitters, contactors,
3.1. ASSEMBLING
ADA-13110M converter case is adapted to assembly on TS-35 (DIN35) rail. To install the device on TS-35 should be the upper part
of the casing put hooks on the terminal and then press the bottom of the cover until you hear a characteristic "Click" sound.
3.2. ETHERNET NETWORK CONNECTION
ADA-13110M has to be connected to ETHERNET network by the use of the switch, the HUB or directly to the PC network adapter.
The table below shows preparing of the straight cable for converter connection to switch or hub.
6
ADA-13110MG
Power Supply
10 - 30VDC
ETHERNET RS232
3-WAY ISOLATION
Power Supply
10 - 30VDC
ETHERNET RS232
POWER ISOLATION

Table 1. T e straig t cable for connection to switc or ub.
RJ45 Pin
No.
Signal Wire Color
EIA/TIA 568B
Straig t cable
UTP 4x2x0,5
Wire Color
EIA/TIA 568B
Signal RJ45 Pin
No.
1 TX+ White-Orange
2 TX- Orange
3 RX+ White- reen
4 Not used Blue
5 Not used White-Blue
6 RX- reen
7 Not used White-Brown
8 Not used Brown
White-Orange TX+ 1
Orange TX- 2
White- reen RX+ 3
Blue Not used 4
White-Blue Not used 5
reen RX- 6
White-Brown Not used 7
Brown Not used 8
The table below shows preparing of cross-over cable for the converter connection to PC network adapter or connections converters
together for functioning as point-to-point serial bridge.
Table 2. T e cross-over cable for connection to PC network adapter or connections converters toget er for functioning as
point-to-point serial bridge.
RJ45 Pin
No.
Signal Wire Color
EIA/TIA 568B
Cross-Over Cable
UTP 4x2x0,5
Wire Color
EIA/TIA 568B
Signal RJ45 Pin
No.
1 TX+ White-Orange
2 TX- Orange
3 RX+ White- reen
4 Not used Blue
5 Not used White-Blue
6 RX- reen
7 Not used White-Brown
8 Not used Brown
White- reen TX+ 1
reen TX- 2
White-Orange RX+ 3
Blue Not used 4
White-Blue Not used 5
Orange RX- 6
White-Brown Not used 7
Brown Not used 8
In the modular socket ETHERNET interface of converter, are implemented two LED's (Fig. 1):
–reen ACT signalling state of sending or receiving data,
–Orange LINK signalling active network connection.
ADA-13110MG converter can function in t e ETHERNET network as:
–virtual serial bridge [RealPort],
–TCP serial bridge,
–UDP serial bridge.
Additional information about Ethernet connection will be describe in chapters below.
3.2.1. CONNECTING TO NETWORK ADAPTER OF PC
If there is not the switch or the HUB, it is possible to connect the ADA-13110M directly to a network adapter of PC using the cross-
over cable (Table 2). This connection can be used for converter configuration.
Fig. 3. Direct connection to PC
3.2.2. CONNECTING FOR OPERATING IN REALPORT MODE
Figures 3 (above) and 4, 5 (below) show how correctly connect the ADA-13110M to LAN, WAN network or PC, for operating in
virtual serial port mode (RealPort).
For direct connection of the converter to PC network adapter, use the cross-over cable (see Table 2) and for connection by the use of
switch or HUB use the straight cable (see Table 1).
7
ADA-13110MG
PC with a network
adapter
Static IP address
ADA-13110M
Static IP address
ETHERNET
Crossover cable
(Table 2)

Fig. 4. LAN connection via switc / ub to operating in t e Real Port mode
Fig. 5. WAN connection to operating in t e Real Port mode
3.2.3. CONNECTION FOR OPERATING IN TCP & UDP SERIAL BRIDGE MODE
Pictures below show how correctly connect the ADA-13110M to ETHERNET network for functioning in TCP & UDP serial bridge
mode.
For connection by the use of network devices (router, switch or HUB) use the straight cable (see Table 1).
8
ADA-13110MG
ETHERNET
Straight Cable
(Table 1)
Local network
ETHERNET
built on the switch
Device with
RS232 interface
RS232
PC with a network
adapter
Static IP address
ADA-13110M
Static IP address
INTERNET
ROUTER
Public IP address
RS232
ROUTER
Public IP address
ETHERNET
Straight Cable
(Table 1)
Device with
RS232 interface
PC with a network
adapter
Static IP address
ADA-13110M
Static IP address
ETHERNET
Straight Cable
(Table 1)

Fig. 6. T e LAN connection to operating in t e TCP/UDP serial bridge mode, one-to-one
Fig. 7. T e LAN connection to operating in t e UDP serial bridge mode, one-to-many
9
ADA-13110MG
RS232
RS232
ETHERNET
Straight Cable
(Table 1)
Local network
ETHERNET
built on the switch
Device with
RS232 interface
ADA-13110M
Static IP address
Device with
RS232 interface
ADA-13110M
Static IP address
ETHERNET
Straight Cable
(Table 1)
RS232
RS232
RS232
Local network
ETHERNET
built on the switch
SLAVE device
with
RS232 interface
ADA-13110M
Static IP address
ETHERNET
Straight Cable
(Table 1)
ADA-13110M
Static IP address
ADA-13110M
Static IP address
ETHERNET
Straight Cable
(Table 1)
SLAVE device
with
RS232 interface
MASTER device
with
RS232 interface

3.2.4. CONVERTERS CONNECTION AS MODBUS GATEWAY
Figure 8 shows connection of ADA-13110M to ETHERNET network ETHERNET(LAN) to operating in Industrial Automation Mode
(MODBUS Gateway). This type of connection allows integrating MODBUS-TCP devices and MODBUS-RTU/ASCII devices in one
network.
Fig. 8. Integration of Modbus-TCP MODBUS-RTU/ASCII into a single network using ADA-13110MG wit MODBUS Gateway
3.3. RS232 DEVICES CONNECTION TO ADA-13110MG
3.3.1. CONNECTING OF DEVICE WITH RS232 PORT, DTE TYPE (PC COMPUTER)
ADA-13110M can be connected to RS232 port of PC computer by the use of RS232 extension cable CAB-DB9F/DB9F-C-1,8m
(available in our offer). Picture below shows the example connecting to RS232 PC port.
Fig 9. Example connection of ADA-13110MG to RS232 PC
10
ADA-13110MG
Cable / Adapter
CAB-DB9F/DB9F-C-1,8m /
ADP-DB9F/DB9F-C
Tx+ (1)
Tx- (2)
Rx+ (3)
Rx- (6)
ADA-13110M
V +
V -
V -
V +
1
2
3
4
6
5
9
7
8
Rx -2
Tx -3
DTR -4
DSR -6
RTS -7
RI -9 (NC)
GND -5
DCD -1
CTS -8
1
2
3
4
6
5
9
7
8
Rx -2
Tx -3
DTR -4
DSR -6
RTS -7
RI -9
GND -5
RS232 port
DTE/DB-9M
DCD -1
CTS -8
RJ45
ETHERNET
connector
Power supply
RS232
DTE/DB-9M
connector
DB-9F
socket
Device with
RS232 port
DTE type
LAN, WAN network
or PC
DB-9F
socket
RS232
MODBUS-RTU/ASCII
SWITCH - ETHERNET
PC with
SCADA / HMI
MODBUS-TCP
ADA-13110M
MODBUS ateway
ADA-13110M
MODBUS ateway
RS232
MODBUS-RTU/ASCII
MOSBUS-RTU
MASTER
MODBUS-TCP
MODBUS-TCP
MODBUS-TCP
MODBUS-TCP
MODBUS-TCP
LAN ETHERNET
MODBUS-TCP
LAN network
MODBUS-ASCII
SLAVE

3.3.2. CONNECTING OF DEVICE WITH RS232 PORT, DCE TYPE (MODEM, CODE READER)
ADA-13110M can be connected to RS232 device DCE port type by the use of RS232 cable CAB-DB9F/DB9M-S-1,8m (available in
our offer). Picture below shows the example connecting.
Fig 10. Example connection to RS232 device DCE port type (eg. modem, code reader) to ADA-13110MG
3.4. POWER SUPPLY CONNECTION
The power supply to the ADA-13110M converter should be DC (regulated) from 10 V= to 30V=. Nominal power is typically 3W, e.g.
HDR-15-24. Power cable from DC power supplies to device must not be longer than 3m.
Observe the polarity, connect positive (+) of DC power supplies to V+ and negative (-) end to V- terminal.
ADA-13110M has the protection from opposite connection power supply.
4. ACTIVATION
Converter can be powered after proper connection according to step above. If the connection was made properly green LED PWR on
front panel of converter should lit, if not check polarization of power connection. During proper data transmission through converter
the LEDs Tx and Rx on the front panel and on RJ45 connector of Ethernet interface should blink. These LEDs are respectively:
LED Description
RS232 interface & Power
PWR Signalization of power supply
RX Signalization of data receiving by ADA-13110M converter from RS232.
TX Signalization of data transmission from ADA-13110M converter through RS232.
RTS ADA-13110M reports to device readiness data collection
CTS Device confirms reception RTS signal from ADA-13110M
DTR Readiness of ADA-13110M to receive/send data
DSR Readiness of Device to receive/send data
DCD Level of received signal
ETHERNET interface
yellow LINK Signalling a valid connection to the network
green ACT Signalling data transmission
5. CONFIGURATION
ADA-13110M converter like most of network devices should be configured for proper functioning, it's needed configuration of
network services and network setting.
Below are described the stages of software installation and network setting configuration of converter.
11
ADA-13110MG
Tx+ (1)
Tx- (2)
Rx+ (3)
Rx- (6)
ADA-13110M
RJ45
ETHERNET
connector
V +
V -
Power supply
RS232
DTE/DB-9M
connector
Tx -2
Rx -3
DSR -4
DTR -6
CTS -7
RI -9
GND -5
V -
V +
Cable / Adapter
CAB-DB9F/DB9M-S-1,8m /
ADP-DB9F/DB9M-S
DB-9M
plug
1
2
3
4
6
5
9
DB-9F
socket
Device with
RS232 port
DCE type
RS232 port
DCE/DB-9F
DCD -1
7
RTS -88
1
2
3
4
6
5
9
7
8
Rx -2
Tx -3
DTR -4
DSR -6
RTS -7
RI -9 (NC)
GND -5
DCD -1
CTS -8
LAN, WAN network
or PC

5.1. INITIAL CONFIGURATION USING ADAFINDER SOFTWARE
5.1.1. ADAFINDER INSTALLATION
The initial configuration of network setting at the converter can be made by using ADAFinder or ADAWiz software. The installation is
automatically after insert the CD (compact disc) to an optical drive. If the autorun doesn't start, should run the file setup.exe located in
main CD catalogue. After installation the software ADAFinder and ADAWiz are available in Start->Programs->CEL-M R-> D Net.
5.1.2. NETWORK SETTING
ADAFinder is use for initial configuration of converter's network setting.
Before running ADAFinder s ould be disabled t e System FireWall!
After running, the program is searching local network and if find ADA-13110M , will add them to the list of available converters
[Devices:], like on the picture below.
Fig 11. Base configuration network by t e use ADAFinder software
To c ange t e network setting of ADA-13110MG, s ould:
–select the converter from the list [Devices:] and press [Configure IP Settings ],
–in windows [Set IP Address] select option 'Automatically obtain network settings via DHCP' (default setting) or 'Manually
configure network setting'. In case of manual configuration should be enter IP Address of the converter, Subnet Mask, Default
ateway and the Password (default: dbps) of the ADA-13110M administrator for authorization of changes.
–press [Apply], configuration will be saved to the converter and will restart. After message 'Operation made successfully', press
[Refres List] in ADAFinder window. After re-searching the lists of available converters [Devices:] will be refreshed.
Other buttons of the program main menu:
–selecting the converter from the list and pressing [Reboot Device], will make programmable reset of the converter – new
configuration of network setting will be activated,
–selecting the converter from the list and pressing [Device Information], will show an information about setting of the converter,
–selecting the converter from the list and pressing [Open Web Interface], will run Internet browser and open the configuration page
of the converter.
12
ADA-13110MG

Fig 12. ADAFinder configuration of IP network address
5.2. CONFIGURATION AND MANAGEMENT BY THE USE OF INTERNET BROWSER
Integrated WWW server to ADA-13110M enable to easy configuration and diagnostics of LAN and WAN network devices by the use
Internet browser.
For configuration open the Internet Browser and type the address ttp://<ip-converter-address>/admin/administration. tm. Login
windows will open. Enter User name and Password as follows:
User name: root
Password: dbps
If the User name and the Password are correct, will open the page as below.
Fig 13. T e web page for configuration and management of ADA-13110MG
13
ADA-13110MG

5.2.1. NETWORK CONFIGURATION
To make changes of default setting or new configuration of ADA-13110M , select on left panel Configuration -> Network and then
on right [IP Settings] (Fig.13) and make the selection: Obtain an IP address automatically using DHCP or Use t e following IP
address (in this option, enter IP Address of the converter, Subnet Mask, Default ateway), press [Apply] for save. After the message
C anges ave been saved successfully, from left menu select Administrator -> Reboot on right press [Reboot], will be
programmable reset of the converter and new configuration of network setting will be activated.
Fig 14. T e web page for network setting of ADA-13110MG
5.2.2. SERIAL PORT CONFIGURATION
The configuration of serial port of ADA-13110M converter includes: port description, setting of port profile (operating mode) and
setting of serial transmission parameters (baud rate, data bits, parity, stop bits).
Select on left panel Configuration -> Serial Ports and then on a page Serial Port Configuration select [Port 1], will open the
configuration details page, includes:
–Port Profile Settings,
–Basic Serial Settings,
–Advanced Serial Settings,
5.2.2.1. SERIAL PORT PROFILE CONFIGURATION (OPERATING MODE)
Select on right panel Serial Port Configuration -> Port Profile Settings and then press C ange Profile... will open the page Select
Port Profile for selection of available port profiles (picture below).
ADA-13110M operates properly in profiles as follows:
–RealPort
–TCP Sockets
–UDP Sockets
–Serial Bridge
Configuration of profiles will be presented in next chapters.
14
ADA-13110MG

Fig 15. T e web page for selection serial port profile
5.2.2.1.1. REALPORT (VIRTUAL PORT) CONFIGURATION
Choosing RealPort (Virtual Port, Fig. 15) is configured the serial port of ADA-13110M , for communication with virtual port COM of
computer. Press [Apply] for save. After installation driver (RealPort) of virtual port COM (see chapter 6) in operating system, data
sending by application to this port are transferred through WLAN/WAN to ADA-13110M converter and are present on his serial port.
The driver RealPort installation is presented in chapter 6. Normally RealPort service allows for one connection through WLAN/WAN,
between computer and server port.
Connection from other computers to the converter will be not taken, what will cause the error message.
5.2.2.1.2. TCP SOCKETS CONFIGURATION
Choosing TCP Sockets is configured the serial port of ADA-13110M , for direct communication with PC or other network device by
the use of TCP socked. Data sending by application/device to TCP socked are transferred through network to ADA-13110M
converter and are present on his serial port. To save selected configuration, press the button [Apply].
5.2.2.1.2.1. TCP SERVER & CLIENT CONFIGURATION
After saving the profile in section TCP Server Settings, set parameters:
- port for Telnet service, in standard 2001,
- port for serial port service, in standard 2101 (via this port the data are sent to serial port of server),
- port for safe access to serial port service, in standard 2601 (via this port the data are sent to serial port of server),
Additionally, there is the possibility of selection Enable TCP Keep Alive – connection will be kept, even if the data is not transmitted
over the network.
15
ADA-13110MG

Fig. 16. Example configuration of TCP server
For configuration of TCP Client Settings (TCP Client Setting, fig. below), select Automatically establis TCP connections,
connection between client and TCP server will be automatically. Then select Always connect and maintain connection option and
in section Establis connection to t e following network service enter IP address of device to which TCP client will send data,
select service and enter port. There is also possible to select an option Enable TCP Keep-Alive – connection will be kept, even if the
data is not transmitted over the network.
For saving the configuration press [Apply].
Fig 17. Example configuration of TCP client
ATTENTION !
Default port of serial port service is 2101.
If on t e local network is conflict wit ot er network service using t e same port, in t e converter's port configuration
c ange number of port into anot er for t e server and client service .
5.2.2.1.2.2. THE 'ENABLE TCP KEEP-ALIVE' OPTION CONFIGURATION
Option Enable TCP Keep-Alive keeps connection between server and client, even if the data is not transmitted over the network and
reconnection in case of interruption.
Configuration of this option can be made by selection Configuration -> Network -> Advanced Network Settings -> TCP Keep-Alive
Settings. In this section can be configured:
– Idle Time – specifies the period (scope 10 sec. - 24 hours) that a TCP connection has to be idle before a keep-alive is sent.
– Probe Interval – the time in seconds between each keep-alive probe (scope 10 – 75 sec.),
– Probe Count – the number of times TCP probes the connection to determine (scope 5 – 30 trials).
16
ADA-13110MG

5.2.2.1.2.3. SERIAL PORT TRANSMISSION PARAMETERS CONFIGURATION
For proper operation of ADA-13110M with device connected to his serial port, should be set the same transmission parameters for
both devices.
Select Basic Serial Settings and enter Baud Rate, Data Bits, Parity, Stop Bits, the same parameter like has device connected to
the serial port of the converter.
5.2.2.1.3. UDP SOCKETS CONFIGURATION
Choosing UDP Sockets is configured the serial port of ADA-13110M converter for direct communication with PC or other device
connected to the network by the use of UDP socked. Data sending by application or other device/s to this port are transferred through
LAN/WAN to ADA-13110M converter and are present on his serial port. Press [Apply] for save the configuration.
5.2.2.1.3.1. UDP CLIENT & SERVER CONFIGURATION IN CASE OF MASTER DEVICE
After saving the UDP Sockets profile, will open section UDP Server Settings with operating parameters like on picture below. Set
access to UDP server on e.g. 2101 port. Then select Automatically send serial data in section UDP Client Settings, this
automatically send received data by the use UDP client service to the SLAVE device connected to LAN/WAN through e.g. ADA-13021
ADA-13020, ADA-13028L, ADA-13040M , ADA-13110, ADA-14040, ADA-14040.
On lists Send data to t e following network services are addresses of network devices and ports to which will be send data. In
fields:
–Description - enter e.g. location of the converter and SLAVE device,
–Send To - enter IP address of e.g. converter, connected to SLAVE device,
–UDP Port - enter the number of port on which is working UDP Server of converter connected to SLAVE device
In the section Send data under any of t e following conditions is recommended to set parameters like on picture bellow.
For saving the configuration of UDP client and server for MASTER device, press [Apply].
Fig 18. Example configuration of t e UDP server&client on converter connected to MASTER device
17
ADA-13110MG

5.2.2.1.3.2. UDP CLIENT & SERVER CONFIGURATION IN CASE OF SLAVE DEVICE
Set operating parameters of UDP server on the converter connected to SLAVE device eg. like on picture below. Set access to UDP
server on e.g. 2101 port. Then select Automatically send serial data in section UDP Client Settings, this automatically send
received data by the use UDP client service to the MASTER device connected to LAN / WAN through e.g. ADA-13020, ADA-13028L,
ADA-13040M , ADA-13110, ADA14040, ADA-14040.
On lists Send data to t e following network services are addresses of network devices and ports to which will be send data. In
field:
–Description - enter e.g. location of the converter and MASTER device,
–Send To - enter IP address of converter connected to MASTER device,
–UDP Port - enter the number of port on which is working UDP Server of converter connected to MASTER device
In the section Send data under any of t e following conditions is recommended to set parameters like on picture bellow.
For saving the configuration of UDP client and server for SLAVE device, press [Apply].
Fig 19. Example configuration of t e UDP server&client on converter connected to SLAVE device
ATTENTION !
Default port of serial port service is 2101.
If on t e local network is conflict wit ot er network service using t e same port, in t e converter's port configuration
c ange number of port into anot er for t e server and client service .
5.2.2.1.3.3. SERIAL PORT TRANSMISSION PARAMETERS CONFIGURATION
For proper operation of ADA-13110M with device connected to his serial port, should be set the same transmission parameters for
both devices.
Select Basic Serial Settings and enter Baud Rate, Data Bits, Parity, Stop Bits, the same parameter like has device connected to
the serial port of the converter.
18
ADA-13110MG

5.2.2.1.4. SERIAL BRIDGE PROFILE CONFIGURATION
Choosing the Serial Bridge profile enable direct communication between two devices connected to two ADA-13110M converters
over the network as if they were connected with a serial cable. A properly configured ADA-13110M will start automatically
communication with each other. Press [Apply] for save the configuration
After saving the Serial Bridge profile, will open section Serial Bridge Settings (fig. below) with operating parameters like on picture
below. Select Initiate serial bridge to t e following device option and enter IP address and 2101 port of the converter with which to
create the serial bridge over the network. Additionally, can be selected [Enable TCP Keep-Alive] option which keeps connection even
if the data is not transmitted. Select Allow ot er devices to initiate serial bridge and enter 2101 port on which other the converter
will automatically start communication and can be set also [Enable TCP Keep-Alive] option which keeps connection even if the data
is not transmitted.
Fig 20. Example configuration of TCP Serial Bridge
ATTENTION !
Default port of serial port service is 2101.
If on t e local network is conflict wit ot er network service using t e same port, in t e converter's port configuration
c ange number of port into anot er for t e server and client service.
5.2.2.1.4.1. SERIAL PORT TRANSMISSION PARAMETERS CONFIGURATION
For proper operation of ADA-13110M with device connected to his serial port, should be set the same transmission parameters for
both devices.
Select Basic Serial Settings and enter Baud Rate, Data Bits, Parity, Stop Bits, the same parameter like has device connected to
the serial port of the converter.
5.2.2.1.5. INDUSTRIAL AUTOMATION (MODBUS GATEWAY) CONFIGURATION
Choosing the Industrial Automation (Modbus Gateway, Fig.15) profile, will be possible to configure ADA-13110M for
communication by the use of MODBUS-RTU master/slave or MODBUS-ASCII master/slave protocol. The converter converts frames
of MODBUS-RTU/ASCII protocol to MODBUS-TCP and send via WLAN/LAN/WAN to devices with MODBUS-TCP protocol or other
servers (ADA-14040, ADA14110, ADA-13040M , ADA-13110M ) operating in Industrial Automation (MODBUS Gateway) mode
with connected MODBUS-RTU/ASCII devices. Press [Apply] for saving this profile.
5.2.2.1.5.1. CONFIGURATION FOR COMMUNICATION WITH DEVICES MODBUS-
MASTER TYPE
In section Industrial Automation Settings, press [C ange Protocol] link. Then in section Select IA Protocol (figure below) select
type of device, connected to serial port of ADA-13110M , as Serial Master and MODBUS-RTU or MODBUS-ASCII protocol for
communication between connected devices. Press [Apply] for saving configuration.
19
ADA-13110MG

Fig. 21. Example configuration for communication wit MODBUS-MASTER devices – c oice of devices and protocols
Set the options in section Modbus RTU Settings like on the figure below and press [Apply].
Fig. 22. Example configuration for communication wit MODBUS-MASTER devices – Modbus RTU setting
Then select section Slave Destinations (Packet Routing) – figure below.
In this section press [Add], enter the IP address of Slave type devices, to which Master will send requests and receive responses.
Fig. 23. Example configuration for communication wit MODBUS-MASTER devices – table configuration of SLAVE type
devices
In section Destination Settings (fig. below) set the options of requests from Master device to Slave device, in fields:
–Host name - enter IP address of Slave device.
–Protocol - set protocol which will be send to Slave device – in this case will be Modbus/TCP.
–Transport - set TCP protocol .
–Network port - set port 502.
Press [Apply] for saving configuration. Then press again [Add] for adding another Slave device.
Then select section Slave Destinations (Packet Routing), when all Slave devices are added and set, press [Apply].
20
ADA-13110MG