Celexon Electric Professional User manual

Operating instructions
celexon Manual Professional
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully
before connecting or operating this product. Please retain these instructions for future
reference.
Version: 32422_031

1
The purpose of these operating instructions is to familiarise you with the ope-
ration of this product. Therefore, keep these instructions in a safe place so that
you can refer to it at any time.
• Before installation, please refer to the enclosed data sheet for further
safety and use instructions.
• Do not begin installation until you have fully read and understood the
complete operating instructions.
• This product should only be installed by qualied personnel with
mechanical and electrical knowledge.
• Carry out the installation with another person to ensure safe installation.
• Remove the product from its packaging and remove all packaging
materials. Make sure that no packaging material is on or in the product. If
you notice any damage to the packaging, also check for damage to the
product.
• If you notice any external damage to the appliance or any unexpec-
ted or unusual functioning, do not use the product further. Immediately
contact the dealer from whom you purchased the product or celexon
directly (Web: www.celexon.co.uk, Mail: [e-mail]) for further
information.
• To ensure trouble-free operation, the product may only be used indoors. It
is NOT suitable for outdoor use.
• The use of the appliance and accessories is forbidden to children under 16
years of age.
• Ensure that no children play with the appliance or are in the vicinity
without supervision.
• Modifying or altering the product may compromise product safety.
• Caution: Risk of injury! Never open the product yourself unauthorised.
Never carry out repairs yourself!
• This product can only be used under the standard technical parameters.
• Do not use the product near corrosive gas, water or in a dusty
environment.
• Handle the product with care. It can be damaged by knocks, blows or
drops from even a small height.
• Keep the product away from moisture and heat. Never immerse the
product in water or other liquids.
WARNINGS

2
• Use the product only in the manner for which it is intended. Use for any
other purpose may result in damage to the product or its surroundings.
• Carry out the installation with another person to ensure safe installation.
• Tighten the screws, but do not overtighten them. Overtightening (e.g.
tightening using a cordless screwdriver) can cause damage and impair the
secure hold of the screen.
• Suspended loads must be checked at least twice a year for strength and
load-bearing capacity at least twice a year.
• Children should not use the screen or play under it unsupervised.
• Failure to follow the above instructions may result in personal injury and
damage to the product or equipment. Incorrect installation or use may also
invalidate the warranty
• If you are unsure about the use of the product, please contact your
• specialist personnel, your dealer or celexon directly
(Web: www.celexon.co.uk, Mail: [e-mail])
• Technical changes and errors expected.
The manufacturer accepts no responsibility for damage to property or
personal injury if the screen is used outside the recommended
specications or for improper installation. Do not use this screen near heaters or air
conditioners. Also do not mount product in direct sunlight or in front of a
window. Due to the temperature-sensitive PVC surface, the projection screen
may be permanently damaged.
We recommend that you wait approx. 2 hours after delivery before
installing the projection screen.This allows the projection screen to acclimatise,
especially if the screen is moved from a cold to a warm environment.
Please avoid any stains on the surface of the fabric. These may not be able to
be removed.

3
DISCLAIMER
The information in this document is subject to change without notice by the
manufacturer. Changes will be added to subsequent versions of this manual.
The manufacturer does not guarantee or warrant for the correctness of the
information in this document.
CARE INSTRUCTIONS
NEVER clean the screen with alcohol or other cleaning agents that contain
solvents. Use only a soft and clean cloth. A mild soap solution (max 5%) may
be used to remove dirt from the surface. Avoid contact with sharp or pointed
objects as these could permanently damage the projection screen
fabric. Further instructions can be found in the enclosed projection screen
instructions.

4
IN THE BOX
INSTALLATION NOTES
Install the screen in a position that is fully visible to all viewers! The optimum
installation height corresponds to the position of the viewers in the centre of
the screen with the screen fabric extended: eye level = lower third of the screen
surface.
The screen can be installed on the wall/ceiling or hung from the ceiling on
closed ring eyelets plus screwable karabiners (the eyelets are already on the
side cap). For wall or ceiling installation only, the eyelets should be removed
in advance). Please make sure that the metal plates are also used for wall and
ceiling mounting, otherwise safe installation cannot be guaranteed).
The enclosed installation material is intended for a solid stone wall. If
necessary, obtain suitable mounting material for your installation surface.
Attach the eyelets with the washers
and the plates and the nuts to the two
side caps and measure the distance
between the eyelets. Mark the points
on the ceiling and make sure
make sure that the eyelets are aligned
with each other and parallel to the wall.
1 x Screen
MOUNTING ON THE CEILING (VIA EYELETS)
2 x Plates
4 x Plastic dowels
4 x Nut
4x Screws 2x Ceiling eyelets

5
Measure the distance between the
holes in the side caps (two per cap)
and transfer them to the ceiling. Drill
the holes at the markings to the right
diameter for the mounting material,
insert and screw the screen in place
tightly. Make sure that the holes are
parallel to the wall! Use dowels and
screws suitable for your base.
Caution: Do not overtighten the
screws! If you notice cracks in the caps
they must be replaced! The screen
must not be used with cracked caps.
Please ensure that the metal plates are
also used for wall and ceiling mounting,
otherwise a safe installation cannot be
guaranteed).
Drill the holes at the markings in the
diameter to match the ring eyelets
used, screw them  rmly into the ceiling
(using plugs where appropriate and in
accordance to the manufacturer and
the load of the of the screen) and hang
the screen from them.
MOUNTING ON THE CEILING (SCREWED)

6
MOUNTING ON THE WALL
Measure the distance between the
holes in the side caps (two per cap)
and transfer them to the wall.
Drill the holes at the markings with the
holes with the right diameter for the
mounting material and make sure that
the drill holes are absolutely level (Use
a spirit level!).
Use dowels and screws that are
suitable for your mounting
surface. Screw the two upper screws
into the wall most of the way and hang
the screen from both sides into the
upper hole. Make sure that the screen is
installed straight and level. Tighten
the screws and then tighten the lower
screws on both sides of the screen.
Caution: Do not overtighten the
screws! If you notice cracks in the caps
they must be replaced! The screen
must not be used with cracked caps.
Please ensure that the metal shims are
also used for wall and ceiling mounting,
otherwise a safe installation cannot be
guaranteed).

7
OPERATION
Pull the fabric by the handle of the
weighted bar to the desired position
(Fig. 1). Wait 1-2 seconds and slowly
release the handle until the screen
locks. The screen can be locked at mul-
tiple lengths.
STEP 2: RETRACT THE SCREEN
STEP 1: PULL DOWN THE SCREEN
celexon Europe GmbH | Gutenbergstraße 2 | 48282 Emsdetten | DE
Pull the fabric down a few
centimetres quickly so that the
mechanism is unlocked (Fig. 2).
When the lock is released, you will feel
a slight retraction. Move the screen
vertically upwards at an even speed. Do
not allow the screen to retract upwards
without being guided, therwise the bar
will enter the housing at great speed
and the abrupt force can damage the
screen and side caps. The screen could
fall down and injure people!