Magiboards Chameleon Whiteboard User manual

What you will have included in each pack:
Chameleon Range Instruction Sheet - Individual Panels
www.magiboards.com |01952 2 9 2111 |[e-mail] |pg 2
Create,Shape & Communicate
A x 1
D x 4 F x 8E x 8B x 4 C x 8
PACK A
PACK B
Before you use your new whiteboard for the first time make sure you clean all the panels thoroughly.
If you have any further enquiries on how to fit your whiteboard please contact our customer service team.
PACK A:
1 x Unframed Whiteboard Panel A
PACK B:
4 x Board Fixing Brackets B
8 x Short Screws C
4 x Wall Fixing Brackets D
8 x Long Screws E
8 x Rawl Plugs F
INST_CHAMPAN01

Positioning of whiteboard on the wall KEY
Marking the position of the holes Fixing screwed to the wall
Slot together
20mm
128mm
Chameleon Range Instruction Sheet - Individual Panels
Create,Shape & Communicate
Back of board - Landscape Back of board - Portrait
Y Y
Z Z
XX
Fixings you will need B x 4: and C x 8:
A = Back
of board
Back of
board
Back of
board
Wall Wall
A A
BB
STEP 1 - WHITEBOARD PANEL
STEP 2 - WALL
STEP 3 - TO FIX
STEP 4 - SLOT TOGETHER
DIAGRAM 1 DIAGRAM 2
Z + 2mm =
+
Line up the holes in the back of the board (A) with the
holes in the board fixings (B).
Positioning the brackets will depend on whether you
want your board landscape or portrait - see diagrams
1 and 2.
Take the small screws (C) and screw these into place as
shown in diagrams 1 and 2.
Make sure that they are suitably tightened.
Decide where you want your whiteboard to go on your
wall. Using a pencil, mark on where the corners of the
whiteboard will be (W).
From where you have decided the top of the whiteboard
will be, measure 128 mm down, and mark this with a pencil
line across, ensuring that it is straight using a spirit level. This
is LINE 1.
Next measure out 20 mm from the inside of both sides and
mark these as well. These will both be LINE 2.
Measure the length of Z (see diagram 1 or 2), draw a line
vertically Z + 2 mm down from line 1. This will be LINE 3.
Line up the bottom of one of the wall fixings (D) with line 1
and the left hand side of the fixing with the left line 2. Mark
onto the wall where the holes in the fixing are.
Repeat this process for all four corners, ensuring that the
line is always at the bottom of the fixing as shown. Once
you have marked the position of all the holes, use an 8mm
drill bit to create 8 holes in the wall and insert a rawl plug
in each hole (F).
Once you have done this, line up the wall fixings (D) with
the rawl plugs (F) and screw the fixings firmly to wall using
the large screws (E).
LINE 1
LINE 1 LINE 1
LINE 1 Calculated by measuring 128mm down
from the top of the whiteboard
LINE 3
LINE 3 LINE 3
LINE 3
W
Calculated by measuring from the top of
the top bracket to the top of the boom
bracket.
Posion of whiteboard
LINE 2
LINE 2 LINE 2
LINE 2 Calculated by measuring 20mm in from
both boom corners of the whiteboard
LINE 2
LINE 2 LINE 2
Once all of your wall fixings are screwed firmly into
place, you can simply lift the whiteboard onto the wall.
The fixings slot together as shown.
Y
W
W W
X
Fixings you will need D x 8: and F x 8:E x 8:
B = Wall
www.magiboards.com |019 52 2 9 2111 |[e-mail] |pg 3
INST_CHAMPAN01