Cerio FPOE-PD80 User manual

v1.5
FPOE-PD80
4Pair Force Power Gigabit PoE++ Splitter
User’s Guide
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2016, All Rights Reserved.
Unpacking Information
Thank you for purchasing our PoE series products. Before installation,
please check that your package contains the following items.
Open the shipping cartons of the splitter and carefully unpack its
contents. The carton should contain the following items:
1.FPOE-PD80 Main Unit x 1
2.Inside diameter 2.1 (PHY) mm DC to DC cable x 1
3.Warranty Card x 1
4.Quick Installation Guide x 1
Hardware Overview
Introduction
FPOE-PD80 4Pair Force Power Gigabit PoE++ Splitter delivers
Power over Ethernet to remote devices. Supports IEEE 802.3af/at
standard and compatible with IEEE 802.3bt Power level. It provides
PoE 50-57V Ethernet power + data input to separate to only
DC/Power output up to 80Watt and only Ethernet/Data output. And
DC output voltage switchable to 12V or 19V and 24V. This Force
High-Power splitter allows a non-compliant device to upgrade to PoE,
it is used to deploy remote non-PoE device with no nearby AC outlets
such as latest WiFi 6 generation 802.11ax WiFi AP, PoE IP Speed
Dome PTZ CAM, industrial PC and remote digital signage display..etc.
Product Application
Highlight Features
Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,
IEEE 802.3ab 1000Base-T, IE EE 802.3af, IEEE 802.3at standard
and compatible with IEEE 802.3bt Power level
Supports 10/100/1000Mbps Gigabit Ethernet
It can use to connect non-PoE compliant devices to an PoE
injector or PoE switch
Supports Output Voltage hot switching for
12VDC/19VDC/24VDC three range adjustable
Max Power Output after split power & data : 80Watt(24V)、
75Watt(19V) and 50Watt(12V)
Supports Ethernet PoE to Separate to only DC/Power and only
Ethernet/Data.
Bundle accessories for inside diameter 2.1 mm(PHY) to 2.1
(PHY) mm DC cable
LED indicators for DC output voltage display of 12V/19V/24V
Supports desktop or wall mounting installation and multiple
units combination for easy to bundles organize the Ethernet
cables

v1.5
Installation
Before Installation
If the device is generally DC-receiving and does not support the POE
function, the FPOE-PD80 can easily be used to accept POE source
power and apply it separately from DC output power.
The FPOE-PD80 separates the power out and provides three kinds of
DC power output through its DIP switch and its voltage and current
shown as below:
DIP Switch :
•
12 VDC / 4.17A (Max)
•
19 VDC / 3.94A (Max)
•
24 VDC / 3.33A (Max)
Caution: Please ensure the output voltage is correct for remote
device. Otherwise it will damage your remote device.
Cables Installation
FPOE-PD80 provides a POE-powered solution for non-PoE devices.
The setup of the splitter can be performed using the following steps:
Connect from "DATA OUT" of FPOE-PD80 to the RJ-45 port of the
remote device.
Make sure first power source that the POWER+DATA in Port of
the splitter is fully connected to the PoE source-powered PoE
Injector or PoE Switch.
Connect the correct DC plug from "DC OUT" of FPOE-PD80 to
the DC port of remote device. (Use a DC cable to connect
devices that are to be powered by DC)
Power on the remote device and the LED for voltage status
indicator on FPOE-PD80 will remains on.
Units Combination
This device can be locked on the wall, (Does not have screw
attachment , you must prepare it yourself) or it can be
combined with multiple units for easy to bundles organize the
Ethernet cables.
LED Indicator :
Output power switching (12VDC / 19VDC / 24VDC)
LED indicators for Power function enable
LED Definition
DC 12V output: 12V Light on
DC 19V output: 19V Light on
DC 24V output: 24V Light on
Notice: Cable and Current-Resistance Loss
DC 24V @ 100Meter : 12.50% with Cat.6 Cable
DC 19V @ 100Meter : 13.33% with Cat.6 Cable
DC 12V @ 100Meter : 14.00% with Cat.6 Cable
Product Specifications
Standards & Hardware Specifications
Standard
IEEE802.3/3u 10BASE-T/100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE802.3af Power over Ethernet (PoE)
IEEE802.3at Power over Ethernet (PoE+)
Compatible to IEEE 802.3bt Power Level (PoE++)
Network Media
10/100BASE-T/TX : UTP Cat. 5 or up
1000BASE-T: UTP Cat. 5 or up
Data Transfer Rate
10/100/1000Mbps (Half-duplex),
20/200/2000Mbps (Full-duplex)
Data PIN PIN 1/2, 3/6 & 4/5, 7/8
Power PIN
End-span (Type-A): PIN 1/2,3/6 ;
Mid-span (Type-B): PIN 4/5,7/8
Ethernet Connector
RJ-45 x1 for Power + Data input
RJ-45 x1 for Data output
ESD Protection Over Voltage protection &Short Circuit Protection
Environmental & Mechanical Characteristics
Max Power
Output
80Watt(DC 24V Output),75Watt(DC 19V Output)
50Watt(DC 12V Output)
Power Interface
DC-Jack
Power Requirement
50~57V PoE Power Source
PoE Input Voltage
50V~57V
DC Output
Control Range
12V/19V/24V three range adjustable by DIP
switch
DC Output Current 24V/3.33A , 19V/3.94A, 12V/4.17A
LED Indicators DC Output LED x3 : 12V or 19V or 24V
Operating
Temperature
0° to 55° C
Storage Temperature -40° to 70° C
Operating Humidity 10% to 90% non-condensing
Storage Humidity 5% to 90% non-condensing
Dimension 84.5 x 80 x 39.5mm ( W x D x H )
Unit Weight
99.8g
Case of Materials
Production Location
ABS
TW Only
Certification FCC, CE, RoHS-compliant