Cerio CS-2224-14P User manual

User’s Manual
CERIO Corporation
CS-2224-24P
PoE CS-2000 Series 2 Combo Gigabit + 24 port 10/100Mbps
Web Managed PoE+ Switch

FCC Warning
This device has been tested and found to comply with limits for a Class A digital device, pursuant
to Part 2 and 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiates radio frequency energy and, if not installed
and used in accordance with the user’s manual, may cause interference in which case user will
be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference
in which case the user many be required to take adequate measures.

1. Introduction .........................................................................................................................................5
1.1 Feature ........................................................................................................................................5
1.2 Package Contents ....................................................................................................................6
1.3 Front Panel.................................................................................................................................7
1.4 Rear Panel Layout....................................................................................................................8
1.5 Connections...............................................................................................................................8
2. Software Configuration ....................................................................................................................9
Example of Segment: (Windows 7) ................................................................................................9
2.1 System login username and password information.....................................................13
3. Management......................................................................................................................................14
3.1 Authentication Configuration..............................................................................................14
3.2 System IP Configuration ......................................................................................................15
3.3 System Status .........................................................................................................................16
3.5 Firmware Update ....................................................................................................................19
3.6 Reboot Device .........................................................................................................................20
4. Port Management.............................................................................................................................21
4.2 Port Mirroring ..........................................................................................................................22
4.3 Bandwidth Control .................................................................................................................23
4.4 Broadcast Storm Control .....................................................................................................24
4.5 PoE .............................................................................................................................................25
5. VLAN Setting.....................................................................................................................................26
5.1 VLAN Mode ..............................................................................................................................26
5.2 VLAN Member Setting (Tag Based) ...................................................................................28
5.3 Multi to 1 Setting.....................................................................................................................30
6. Per Port Counter ..............................................................................................................................31
7. QoS Setting .......................................................................................................................................32
7.1 Priority Mode ...........................................................................................................................32
7.2 Class of Service......................................................................................................................34
7.3 Class of Service Configuration...........................................................................................35
8. Security ..............................................................................................................................................36
8.1 MAC address Binding ...........................................................................................................36
8.2 Service Protocol Filter ..........................................................................................................38
9. Spanning Tree...................................................................................................................................40
9.1 STP Bridge Settings ..............................................................................................................40
9.2 STP Port Setting .....................................................................................................................41
10. Trunk ...................................................................................................................................................42

11. DHCP Relay Agent ...........................................................................................................................45
11.1 DHCP Relay Agent .................................................................................................................45
11.2 Relay Server.............................................................................................................................46
11.3 VLAN MAP Relay Agent ........................................................................................................47
12.Backup/Recovery.............................................................................................................................48
13. Other Setting.....................................................................................................................................49
14. Logout.................................................................................................................................................51
Specifications.............................................................................................................................................52

1. Introduction
The CERIO CS-2224-24P Web Managed is a powerful high-performance 24 port POE Fast
Ethernet switch and support 2 combo Gigabit UTP/SFP uplink ports. The models compliant to
POE IEEE 802.3af, it defines new green power saving idea on PSE Port. That can solve the
limitation of the power outlet location and offer the system relocation easily. CS-2224-24P
layer 2 Web Management switch support Remote on/off control by PoE. And support
Port-base VLAN and IEEE802.1q tag-base VLAN based on ports & VIDs, and bandwidth control
and security support MAC /TCP/UDP Filter etc.
The CS-2224-24P case is designed for small office and can be upgrade to 1U” chassis .It is
ideal for micro-segmenting large networks into smaller, connected subnets for improved
performance, enabling the bandwidth demanding multimedia and imaging applications. You
could easily connect a POE Wireless AP or a VoIP phone or IPCAM to this switch without
looking outlets for them. Over current protection and circuit shorting protection are also
supported to ensure the safety. That high power device provides easy installation and the
limitation of the power outlet location and offers the system relocation easily.
1.1 Feature
Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab
1000Base-T, IEEE 802.3z 1000Base-SX/LX IEEE-802.3af PoE,IEEE802.3at POE+
24port 10/100Mbps TX Auto-Negotiation Ethernet Switch , Have 24 Port PSE/ PoE
function, compliant with IEEE-802.3af class3 /class2/class1 and IEEE802.3at
Support 2 combo Gigabit UTP/SFP uplink ports and IEEE 802.3ab 1000Base-T, IEEE
802.3z 1000Base-SX/LX
Supporting PoE+ Green power Management by Link up mode to auto detect the level
class of Power device, budgets power output for each port. and Power down mode to auto
detect no link/ standby of Power device
Supporting the power up to 30Watt/15.4Watt/7.5Watt/4Watt for each PSE/PoE port
Full/Half-Duplex capability on each TX port , Auto-learning networking configurations
Supports Store & Forward architecture and performs forwarding and filtering
Supporting the flow control: back pressure for Half-duplex and IEEE 802.3x for Full-duplex
mode
Broadcast storm control and supporting store & forward operation
Non-blocking & Non-head-of-line blocking full-wire speed forwarding
Supports TP interface Auto MDIX function for auto TX/RX swap

Automatic Source MAC Address Learning and Aging
Supports up to 4K MAC addresses
Up to 3.5M bits buffer
VLAN and IEEE802.1Q tag-base VLAN based on ports & VIDs; add/remove/modify tag
IEEE802.3ad Link Aggregation Port trunking(up to 3 groups and Max. 4 ports in each
group)
Provide IGMP v1/v2 snooping function
Support QOS Class Quality of service ( COS ), port- based, 802.1q priority tag based, IP
TOS based, TCP/UDP port bases, 4 queues for per port WRR/FIFS algorithm
Support bandwidth control and Broadcast Storm Control
Supports port mirroring and Spanning Tree functions.
Per port MAC address base filtering and TCP/UDP filtering
Supports file backup and recovery
SNMP v1 , SNMP v2C support and Web-based management interface
1.2 Package Contents
Before you start to install this switch, please verify your package that contains the following
items:
CS-2224-24P Main Unit
x1
CD Manual
x1
Power Code
x1
19” Mount Brackets
x1
Warranty Card
x1

1.3 Front Panel
LED Indicators of 24 Port 10/100Mps + 2 giga Switch
1) Power LED the color is Yellow
2) 24 Port PoE and Ethernet Link/ACT LED, Port is linked to Power Device the PoE Lights up
LED, Port is data linked the Link/ACT Lights up LED, The Link / ACT Flashing represent
10/100Mbps for data activating
3) 2 Port Giga linked LED, Port is linked to Giga Device the Speed Lights up LED. Port is data
linked the Link/ACT Lights up LED, The Link / ACT Flashing represent 10/100/1000Mbps
for data activating
4) Hardware Reset to default button, hold down for about 10 seconds, until LED flashes
rapidly, Release will return to the default
24 port + 2 Giga port
1) 24 10/100Mbps PoE Ethernet Port
2) 2 Giga Ethernet Port
3) 2 Fiber Port
1
2 3
4
1 2 3

1.4 Rear Panel Layout
1) AC input (100-240V/AC, 50-60Hz) UL Safety)
2) Two radiator fan
1.5 Connections
Switch/Hub to this 8 Port with 8 Port Fast Ethernet PoE Switch
This switch provides automatic crossover detection functionality for any port. It is simple and
friendly to up-link to another switch without crossover cable.
IP Camera
with PoE
AP With PoE Other devices With PoE
Other devices Un-PoE
1
2
Giga to Giga uplink
xDSL
RJ-45 Data and PoE Out

PC/Other devices to this 24 Port Fast Ethernet PoE Switch
Via a twisted pair cable straight through, this switch can be connected to PCs, servers and
other network devices.
Power Device to this 24 Port with 24 Port Fast Ethernet PoE Switch and getting 48V
power source through Cat. 5/6 cables
Using Cat. 5/6 twisted-pair cable to connect Power Device to the port 1~24 of this switch, and
then this switch will supply 48V power to Power Device over Cat. 5/6 twisted-pair cable. Please
be noted Power Device should also comply with IEEE 802.3af/ IEEE802.3at. and the PoE
Power Max. 30Watt each PSE/PoE port
2. Software Configuration
CS-2224-24P supports web-based configuration. Upon the completion of hardware installation,
CS-2224-24P can be configured through a PC/NB by using its web browser such as Internet
Explorer 6.0 or later.
Set the IP segment of the administrator's computer to be in the same range as CS-2224-24P for
accessing the system. Do not duplicate the IP Address used here with IP Address of CS-2224-24P
or any other device within the network. Please refer to the following steps
Example of Segment: (Windows 7)
Step 1 :
Please click on the computer icon in the bottom right window, and click “Open Network and
Sharing Center”

Step 2 :
In the Network and Sharing Center page, Please click on the left side of “Change adapter
setting” button
Step 3 :
In “Change adapter setting” Page. Please find Local LAN and Click the right button on the
mouse and Click “Properties”

Step 4 :
In “Properties” page, please Click “Properties” button to TCP/IP setting
Step 5 :
In Properties page to setting IP address, please find “Internet Protocol Version 4
(TCP/IPv4)” and double click or click “Install” button.
Double click

Step 6 :
Select “Use the following IP address”, and fix in IP Address : 192.168.2.X
ex. The X is any number by 1 to 253
Subnet mask : 255.255.255.0
And Click "OK" to complete the fixed computer IP setting
Step 7 :
Open Web Browser
Without a valid certificate, users may encounter the following problem in IE7 when they try to
access system's WMI (https://192.168.2.200). There will be a “Certificate Error”, because the
browser treats system as an illegal website.
System login Overview page will appear after successful login.

2.1 System login username and password information
The CS-2224-24P web switch default IP is 192.168.2.200
Into the management page as follows, please enter Username and password
Default IP Address: 192.168.2.200
Default Username and Password
Management Account
Root Account
Username
root
Password
default
After the authentication procedure, the home page shows up. Select one of the configurations by
clicking the icon.

3. Management
3.1 Authentication Configuration
This page allows the user to change the user name and the password.
Please click Management setup

Authentication Configuration
Login as administrator user is root and the password is allowed to change its own password.
Username : Management account is “root”
New Password : Enter a new password if desired ( max. 15)

Check New Password : Enter the same new password again to check.
Click “Save”button to save your changes. Click Reboot button to activate your changes
3.2 System IP Configuration
Here are the instructions for how to setup the local IP Address and Netmask.
Please click Management setup System IP Configuration
System IP Configuration : The administrator can manually setup the system IP
address.
IP Address : The IP address of the system; default IP address is 192.168.2.254

IP Netmask : The Subnet mask of the system; default Netmask is 255.255.255.0
Gateway : Configure the network gateway address
IP Configure : The administrator can manually setup the system IP address
when static IP is available/ preferred.
Dynamic IP:This configuration type is applicable when the CS-2224-24P is
connected to a network with the presence of a DHCP server; all related IP
information will be provided by the DHCP server automatically.
Click “Save” button to save your changes. Click Reboot button to activate your
changes
3.3 System Status
MAC address and system version will be shown on the screen. And setting login time out
Please click Management setup System Status

MAC Address: MAC address of the display system
Number of Ports: Display CS-2224-24P the Ethernet posts information
Description: Provide description of the system.
Firmware version: Show currently the CS-2224-24P of system software version and
software date
Set login Time out: set Idle Time(1~30 Minutes)
Click “Save” button to save your changes. Click Reboot button to activate your changes
3.4 Reset to default
Please click Management setup Reset to default

Click Default button to reset back to the factory default settings and expect Successful
loading message.Then, click Reboot button to activate.
Recover switch default setting excluding the IP address, User name and
Password.

3.5 Firmware Update
Firmware is the main software image that system needs to respond to requests and to manage
real time operations. Firmware upgrades are sometimes required to include new features or
bugs fix. It takes around 2 minutes to upgrade due to complexity of firmware. To upgrade
system firmware, click Browse button to locate the new firmware, and then click Upgrade
button to upgrade.
Please click Management setup Firmware Update
Password : Enter administrator password
Do not interrupt during firmware upgrade including power on/off as this
may damage system.

3.6 Reboot Device
This function allows user to restart system with existing or most current settings when changes
are made. Click Reboot button to proceed and take around one minute to complete.
Please click Management setup Reboot Device