Cerio CS-Series User manual

CS-Series CS-1224XG
24 Port 10/100/1000M Gigabit Switch with 2 SFP 10G
Ports
User’s Guide
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this
document is not up-to-date. Please check with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2016, All Rights Reserved.
Unpacking Information
Thank you for purchasing our CS-Series products. Before installation,
please check that your package contains the following items.
Open the shipping cartons of the switch and carefully unpack its
contents. The carton should contain the following items:
1. CS-1224XG Main Unit x 1
2. Power Code x 1
3. User’s Guide x 1
4. 19” Rack Mount Brackets x 1
5. Warranty Card x 1
Power Consumption
CS-1224XG 7.8 Watts
Dimension & Weight :
CS-1224XG 441 x190 x 44 mm (19 inch) /2.52Kg
Introduction
Gigabit with 10GbE Wired Switch
CERIO CS-1224XG is a high-performance 10/100/1000
Mbps 24 port Gigabit Ethernet Switch with 2 SFP 10G Ports. The
CS-1224XG connectivity is ideal for deployment in SME/SMB core
environments. Provide cost-effective powered solutions for modern
enterprise businesses.
The CS-1224XG Gigabit Switch equips with 2 SFP 10G ports
as uplink ports. This 10G uplink design provides an excellent
solution to expend your network. Also provides high flexibility and
enabling the bandwidth demanded for multimedia and imaging
applications. Users can use 10Gb ports Trunk Switch upgrade
bandwidth up to 20Gbps. Moreover, the 10/100/1000 Mbps
Auto-Sensing ability provides an easy way to migrate Gigabit
network without pain. By integrating both data transmitting cable
and power cord, the hassle of constructing your network can be
eliminated, allowing you to easily connect your wired LAN network.
The CS-1224XG defines new green power saving idea in all
Ports. Using the 802.3az Energy Efficient Ethernet standard, the
network will automatically decrease the power usage when traffic is
low with no setup required. It can solve the limitation of the network
local LAN and offer the system relocation easily Plug & play and all
kinds of network protocols compilation make the installation of the
device both simple and quick.
Key Features
Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,
IEEE802.3ab 1000Base-T, IEEE802.3z 1000Base-X , IEEE802.3az
specifications, IEEE802.3ae 10G Fiber
24 Port 10/100/1000Mbps TX Auto-Negotiation Ethernet Switch
Supports 2 SFP 10G Fiber uplink ports for IEEE 802.3ae 10G
SFP-SR,SFP-LR,SFP-ER
Supports Energy-Efficient Ethernet (EEE) , IEEE 802.3az standard
Supports Green Ethernet features, Link-On and Cable Length Power
Saving, Link-Down Power Saving, Power saving mode support to automatic
cable detection
Half/Full-duplex capability on 10/100/1000M each TX port Auto-learning
networking configurations
Supports Store & Forward architecture and performs forwarding and filtering
IEEE802.3x flow control for Full-duplex, Back Pressure function for
Half-duplex operation
Provides 10K Jumbo frames to improve network utilization of a large file
transfers
Non-blocking & Non-head-of-line blocking full-wire speed forwarding
Supports TP interface Auto MDIX function for auto TX/RX swap
Automatic Source MAC Address Learning and Aging
Supports up to 16K MAC addresses
Up to 12M bits buffer

Installation
Desktop / Rack Installation
This switch can be easily installed on a desktop or rack and allow
easy device access for connecting cables and to the power button. A
minimum of 25mm around the device is recommended for product
saf ety.
Desktop Installation
1. Attach the Rubber feet provided with the switch to ensure
minimal movement of the device
2. Keep the switch away from devices such as radios, broadband
amplifiers, and other transmitters that might cause signal
interferences
3. Distancing the device from moisture is also highly
recommended
Rack Installation
The CS-1224XG can be mounted on a standard 19” rack to allow for
convenient placement and device safety. The switch is supplied with
rack mounting brackets and screws for optional installation.
Required Mounting Materials
1. Two mounting brackets
2. 6 M3 flathead screws
Mounting Procedure
1. Disconnect all cables from the device
2. Place device on a hard surface, the front of the device
must be facing you.
3. Locate mounting holes on the sides of the unit
4. Install mounting brackets using M3 flathead screws on
both sides of the device
5. Place unit onto the rack and secure with proper screws
Reconnect all the cables
Network Cable Configurations
CS-1224XG 24 Gigabit ports with auto-MDI/MDI-X support, there is no
need for any Crossover cables when you connect the device to a
computer, or even another switch. In addition, the auto-negotiation
function auto-senses and adjusts the connected devices whether they
are running at 10Mbps, 100Mbps, or 1000Mbps. To make a valid
connection and obtain optimal performance using appropriate cabling,
please refer to the table below.
Media
Speed(Mbps)
Cable Type
10/100/1000Mbps
Copper
10
Category 3, 4, 5
UTP/STP
100 Category 5 UTP/STP
1000
Category 5e, 6
UTP/STP
10Gbps SFP Module 10000
10G SFP-SR /
SFP-LR / SFP-ER
Module required
differs from one that
came with purchase
Hardware Overview
Rear Panel (Power)
AC input : AC input (100~240V/AC, 50~60Hz)
LED Indicator:
Complete LED indicators displays the status of the Switch and
network status
The front panel LEDs provides instant status feedback, and
assists to monitor and troubleshoot when required.
Power LED Power : (Power Indicator)
On : Power On
Off :
Power Off
LINK/ACT Status LEDs : 10/100/1000Mbps (Ports 1~24 )
Amber :
10/100M Link / Act connected.
Green : The port is 1000M Link / Act connected.
Blinking : A valid link is established, and there is data
transmitting/receiving.
LINK/ACT Status LED : 10Gbps (Ports 25~26 )
Blue :
The port is 10Gbps Link / Act connected.
Blinking : A valid link is established, and there is data
transmitting/receiving.
Product Specifications
Standards & Hardware Specifications
Standards
Conformance
IEEE 802.3i 10Base-T
IEEE 802.3u 100Base-TX,
IEEE802.3ab 1000Base-T
IEEE802.3ae 10G Fiber
IEEE 802.3x Flow Control
Port Configuration
24 ports RJ-45 connectors for 10/100/1000
BASE-TX
2 ports SFP 10G Fiber uplink
Media Access Protocol CSMA / CA
Network Media
10BASE –T: UTP Cat. 3 or up, 100BASE-TX: UTP
Cat. 5 or up, 1000BASE-T: UTP Cat. 5 or up
20Gbps Trunk Switch 10GbE ports to trunk switch for on/off
Support 10G Fiber SFP-SR , SFP-LR , SFP-ER SFP module
Transmission Method Store and Forward
MAC Address Table
16K
Built-in Buffer 12M bits
Data Transfer Rate
10/100/1000Mbps (Half-duplex),
20/200/2000Mbps (Full-duplex)
10Gbps/10000Mbps (Full-duplex)
Auto MDI/MDIX Yes
LED Indicators
Per Port : Link/ACT Status x 24
SFP 10Gb Port: Status x 2
Per Unit : Power x1
Internal Bus Speed 68Gbps
Environmental & Mechanical Characteristics
Power
Consumption
7.8 Watt
Power Type
Power cord: Internal Power supply
Power Requirement
AC 100~240V AC, 50-60Hz Auto-sensing
Operating
Temperature
0° to 40° C
Storage Temperature -40° to 70° C
Operating Humidity 10% to 90% non-condensing
Storage Humidity 5% to 90% non-condensing
Dimension
( W x H x D )
441 x 190 x 44 mm
Unit Weight
2.52kg
Certification FCC, CE, RoHS-compliant