Certa CT3IN1JVCPA User manual

10,000mAh CAR JUMPSTARTER,
VACUUM & POWERBANK
CT3IN1JVCPA

2

3
• Do not use with any other smart clamps other than the one supplied with this product.
• If the jumper cables, cords or product shows any sign of damage, cease use
immediately and contact help.Kogan.com for support.
• This product is suitable for 12V vehicles only. Use with any other type of vehicle will
cause serious damage to the unit and vehicle.
• Do not jump start a car when the battery capacity is below 50%.
• Do not connect two clamps together when the jumper starter is powered on.
• Do not connect both cable clamps to the same piece of metal.
• If the vehicle’s engine does not start on the first attempt, disconnect it from the vehicle
battery and wait at least 30 seconds before reconnecting.
• Once the engine has successfully started, disconnect the clamps within 30 seconds.
• This product does not contain any user serviceable parts. Do not disassemble or
modify the product in any way.
• Do not drop the jump starter.
SAFETY & WARNINGS

4
Jump Starter
Smart Clamps
USB-C Cable
Crevice Tool
Brush Tool
User Manual
COMPONENTS

5
1
Charging port
2
Battery indicator
3
Power button
4
Vacuum indicator
5
USB output
6
Smart clamp input
7
Filter (inside)
8
Protective cap
OVERVIEW

6
Smart Clamps
9
Force start button
10
Smart clamp plug
11
Red jumper cable (+)
12
Black jumper cable (-)

7
Charging the Jump Starter
1. Insert the supplied USB-C cable into the charging port on the jump starter.
2. Plug the USB-C cable into a 5V/2A power adapter (mobile phone charger).
3. It will take approximately 5-6 hours to fully charge.
Note: It is recommended to fully charge the jump starter once every 3-6 months.
(Power adapter is not included)
Charging Your Devices (Power bank mode)
The jump starter can be used to charge your portable electronic devices, such as phones,
tablets, Bluetooth earphones, etc.
Use a USB cable (not included) to connect your device to the USB output on the jump
starter.
OPERATION

8
Using the Vacuum Cleaner
1. Remove the protective cap.
2. Press the power button to turn on the vacuum cleaner.
3. Swap between the brush and crevice tool as needed.

9
Connecting to Vehicle Battery
1. Ensure that battery level is above 50% before attempting to jump start your car.
(press and hold the power button for 3 seconds, the battery indicator will display
the current battery level).
2. Insert the smart clamp plug into the jump starter. The green and red indicators
will alternately flash.
3. Connect the red jumper cable to the positive terminal (+) on the vehicle’s battery.
Connect the black jumper cable to the negative terminal (-) on the vehicle’s
battery. The green indicator will turn solid or the green and red indicators will
alternately flash.
Starting the Vehicle
1. Insert the key into the ignition and turn the vehicle turn on.
2. If the vehicle fails to start, disconnect the jumper cables from the vehicle battery
and wait 30 seconds before reconnecting and trying again.
3. If the vehicle fails to start after two more attempts, you can use the force start
function.
Force Start Function
1. Before using the force start function, ensure that the jumper cables are connected
to the correct battery terminal. Press and hold the force start button for 3 seconds.
2. When the indicator on the smart clamp turns solid green, the vehicle will need to
be started within 30 seconds.
3. Once the vehicle starts, the jumper cables will need to be disconnected
immediately.
START
Force start button

10
• Do not leave this product in direct sunlight or hot environments for extended periods of
time. The operating temperature is -20~60˚C.
• Do not use any chemicals or detergents to clean this product. Wipe with a soft, slightly
damp cloth.
• Ensure the battery is fully charged at least once every 3-6 months.
Smart Clamp
Indicator
Cause
Solution
Red & green
indicators
flashing.
Normal operation. Ready to start
car.
N/A
Solid red
indicator and
buzzer is
chirping.
Jumper cables connected in reverse.
Connect the jumper cables to
the correct battery terminals.
The clamp has short-circuited.
Ensure the jumper cables are
not touching or connected to
the same piece of metal.
Solid red
indicator.
The voltage of the vehicle battery is
higher than 12.6V.
Jump starter is not required
to start the car.
Red indicator
flashing rapidly.
The temperature of the clamp is too
high (above 65˚C ± 5˚C).
Disconnect the jumper cables
and allow to cool until the red
& green indicators begin
flashing.
Green indicator
flashing slowly.
The battery level of the jump starter
is too low.
Recharge the battery.
CLEANING & CARE
TROUBLESHOOTING

11
Vacuum Cleaner
Indicator
Cause
Solution
Solid green
indicator.
Vacuum cleaner is working normally.
N/A
Red indicator
flashes 3 times
and the
vacuum turns
off.
Low battery.
Recharge the battery.
Foreign object stuck in the vacuum
cleaner.
Remove foreign object and
restart the vacuum.
If the indicator flashes red
another 3 times and the
vacuum turns off, the motor
may be faulty.
Motor is faulty.
Cease use immediately and
contact help.Kogan.com for
support.

12
Suction power
≥4000PA
Noise level
≤75db
USB output
5V 2.1A
USB-C input
5V 2A
Short circuit protection
Yes
Over-discharge protection
≤13V ± 0.3V
Over-temperature protection
> 65˚C ± 5˚C
Reverse polarity protection
Yes
Reverse charging protection
≥12.6V ± 0.3V
Dimensions
272 x 65mm
SPECIFICATIONS

13
NOTES

14

15

16
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com