Chamberlain Dial Code User manual

DIAL CODE CONTROLLER
OWNERS MANUAL
Telephone Entry System with 32 Zone control
with
surge suppression
BUILT-IN

1
CU Page
TABLE OF CONTENTS
Dial Code Controller manual
version 3.0
To be installed by Qualified Dealers ONLY!
Dial Code Controller Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Dial Code Controller Features (Inside) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Dial Code Controller Features (Outside) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dial Code Controller Features (Processor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mounting Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Description of Surge Suppression Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Grounding the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Earth Ground Rod Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Basic Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RS-485 Multiple Connections Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RS-485 “Daisy Chain” Connection Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
RS-485 “Star” Connection Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Memory Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Programming the Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Selecting a Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Resident Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Transmitter/Card Reader Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Utility Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Changing the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Clock / Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-24
Strike Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Parts List and Part Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

DIAL CODE CONTROLLER OVERVIEW
2
CU Page
• Two line Large LC Display.
• Memory capacity: 250, 500, 1000 names.
• User-friendly programmability via built-in alpha-numeric
keyboard eliminates the need for user's manual.
• Four character alpha-numeric password required to enter
• Power failure backups:
• Battery backup for complete function for up to 5 hrs.
• Battery enables dial out, program, & display.
• Non-Volatile removable SRAM memory has
unlimited write cycles (unlike EEPROM).
• Non-Volatile Real Time Clock/Calendar.
• Non-Volatile PCMCIA memory card
• Two (2) slots for PCMCIA memory cards.
• Double box with built-in full keyboard for data processing.
• Programmable via modem-2400 bps to 14400 bps.
• FCC part 68 ,15 & Canadian DOC approval
• ETL listed - UL STD 294 and UL 1950
• Surge protection:
– 6000V, 3000A
– Power input port
– Telephone line port
– RS-485 ports
– Relay ports
– Input port
– Immune to 25,000V electrostatic discharge.
• Construction: Front Panel: 16 gauge stainless steel.
Processor Containment Box: Al anodized, powder
coated 16 gauge metal (weather resistant finish)
• Entire system is rain resistant.
• Power Input: 12 VAC, 40VA UL listed transformer.
• Operating Environment:
• Temperature: -4 F to +185 F
(Heater kit available at additional cost.)
• Relative Humidity: 5% - 95% non-condensing.
• Dimensions: 11 1/4" W X 16 7/16" H X 4 1/8" D
• Shipping Weight: Approximately 25 lbs.
Factory to Dealer
3 YEAR WARRANTY
STANDARD FEATURES
SPECIFICATIONS
CVBNM
’
X
Z
A
QWERTYUI
0
7
4
123
56
89
OP
SDFGH J KL
SPACE BAR
EXIT HELP
PROGRAM
ERASE ENTER
BACK
SPACE
SHIFT

DIAL CODE CONTROLLER FEATURES (INSIDE)
3
CU Page
GATE
RELAY
DOOR
RELAY
POWER
Mounting
Holes (4)
Processor Key
Release / Lock
Processor Unit
Dialing Keys
Programming
Keys
Parallel Port
LC Display
Memory
Card Slot
Memory
Card
Memory
Card Release
Buttons
Processor
Power Switch
Stainless
Steel Door
Key Lock
Surge Suppressor
Terminal Board
All components and specifications are subject to change without notice.

DIAL CODE CONTROLLER FEATURES (OUTSIDE)
2
3
1
4
CU Page
16 GAUGE STAINLESS STEEL DOOR -
Heavy-duty and weather resistant.
KEY LOCK - Opens the Processor
Containment Box to access the
Processor.
PROCESSOR CONTAINMENT BOX -
16 Gauge Stainless Steel Powder
Coated.
1
2
3
All components and specifications are subject to change without notice.

CVBNM’
X
Z
A
Q W ERT Y U I
0
7
4
123
5 6
89
OP
SD F G H J K L
SPACE BAR
EXIT HELP
PROGRAM
ERASE ENTER
BACK
SPACE
SHIFT
250
500
1000
Elite Entry Phone
COMMUNICATOR CARD
Remote Access RS-485
capacity
1
2
3
4
7
16
10 14
15
11
12
13
9
8
5
171819
Main Memory Card Slot
RS 485 Memory Card Slot
6
DIAL CODE CONTROLLER FEATURES (PROCESSOR)
MEMORY CARD - STORES ALL PROGRAMMED INFOR-
MATION. (DIFFERENT MEMORY SIZES AVAILABLE)
COMMUNICATOR CARD - CARD FOR RS-485 DEVICES.
POWER ON/OFF SWITCH
CARD RELEASE BUTTONS - EJECT CARDS WHEN
PRESSED.
MAIN MEMORY CARD SLOT - HOLDS MAIN MEMORY
CARD.
RS 485 MEMORY CARD SLOT - HOLDS RF COMMUNI-
CATOR CARD OR BACKUP MEMORY.
LCD TWO LINE, LARGE LIQUID CRYSTAL DISPLAY -
DISPLAYS INFORMATION AND INSTRUCTIONS, TWO
LINES AT A TIME.
DIRECTION KEYS - MOVE CURSOR TO DESIRED
POSITION WITHIN SCREENS.
PROGRAM KEY - SETS PROCESSOR TO THE PROGRAM
MODE.
EXIT KEY - PRESS THIS KEY TO GO BACK TO THE PRE-
VIOUS SCREEN / MENU.
ERASE KEY - ERASES INFORMATION SCREENS
NO LONGER NEEDED.
ENTER KEY - REGISTERS INFORMATION INTO MEMO-
RY AFTER IT IS TYPED.
HELP KEY - HELPS USER WHILE IN PROGRAMMING
OR USER MODES.
SCROLL KEYS - SCROLLS THROUGH SCREENS /
MENUS.
KEYBOARD - WORKS LIKE STANDARD KEYBOARD TO
TYPE IN INFORMATION AND NAMES.
PHONE JACK (RJ11) - CONNECTS TO SURGE SUP-
PRESSOR TERMINAL BOARD.
INPUT/OUTPUT CONNECTOR - CONNECTS TO SURGE
SUPPRESSOR TERMINAL BOARD.
COMMUNICATION PORT - CONNECTS TO SURGE SUP-
PRESSOR TERMINAL BOARD.
PARALLEL PORT - USED FOR THE ICON26 ONLY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
All components and specifications are subject to change without notice.
5
CU Page

MOUNTING SPECIFICATIONS
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
(+)
( )
GND
DOOR NO
DOOR NC
DOOR C
GATE-NO
GATE-NC
GATE-C
12V
AC/DC
GATE
RELAY
DOOR
R LAY
POWER
POWER
INPUT
GND
INPUT
VCR NO
VCR-C
TEL
LNE
TIP
RNG
RS 485 1)
RS 485 2)
RS 485 3)
RS 485 4)
GA E
RELAY
DOOR
RELAY
CHASS S
GROUND
POSTAL EXIT
SW INPUT
VCR
RELAY
1 "
8 "
14 "
11 " 4 "
3 "
"
16 "
1"
1"
Wall
Front View
Mounting Holes (4)
Wire Knock Outs
Side View
1"
Knock
Outs
Installation on Wall
Remove the Processor
Unit from the
Processor Containment
Box and bolt the
Processor Containment
Box to the recess in the
wall using the four
mounting holes. Feed
the power and phone
lines through the
knockout in the back of
the box to make all wire
connections.
Be sure to read and follow all Chamberlain Elite instructions before installating and operating any Chamberlain Elite
products. Chamberlain Elite Entry Phone is not responsible for improper installations or failure to comply with local
building codes. All components and specifications are subject to change without notice.
7/
16
1/
4
1/
4
1/
8
1/
2
1/
2
3/
4
3/
4
8 "
1/
4
6 "
7/
8
6
CU Page

DESCRIPTION OF SURGE SUPPRESSION TERMINAL BOARD
7
CU Page
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
DOOR-NO
DOOR-NC
DOOR-C
GATE-NO
GATE-NC
GATE-C
12V
AC/DC
GATE
RELAY
DOOR
RELAY
POWER
POWER
INPUT
GND
INPUT
VCR-NO
VCR-C
TEL
LINE
TIP
RING
RS-485 (1)
RS-485 (2)
RS-485 (3)
RS-485 (4)
GATE
RELAY
DOOR
RELAY
CHASSIS
GROUND
POSTAL/EXIT
SW INPUT
VCR
RELAY
TELEPHONE LINE: Tip and Ring Connection.
POWER IN: 12 VAC transformer input.
RS 485: Connect to corresponding RS485 terminals (-, +,
GND) of remote security devices.
DOOR RELAY: For allowing access through pedestrian gate or
door.
GATE RELAY: For use with gate operator to control access
through main vehicular gate.
VCR RELAY: For use with Time Lapse VCR. Each time access
is granted, the VCR Relay is activated for 5 seconds, allowing
recording of all access to facility.
POSTAL/EXIT SW INPUT: For allowing postal lock access to
pedestrian gate or door. Activates gate relay using gate strike
time.
CHASSIS GROUND: Entry Phone MUST be properly
grounded. Refer to “Grounding the Unit” and “ Earth Ground
Rod Installation” sections.
POWER LED: Indicates Entry Phone has 12 VAC power.
GATE RELAY LED: Indicates gate relay is activated.
DOOR RELAY LED: Indicates door relay is activated.
2
4
5
6
7
8
1
1
2
3
4
5
6
7
8
9
10
11
3
3
3
3
9
10
11
It is MANDATORY that this unit is properly
grounded. The provided "chassis ground" wire
must be connected to the ground rod. If unit is
not grounded, lightning damage will occur.
Please refer to the owners manual for proper
grounding instructions.
MADE IN USAeliteentryphone.com
Knockouts for
Incoming Wires
Removable Screw Terminal Connectors for Easy Wiring.
POWER IN
12V
AC/DC
NOTE: Telephone line used for Entry Phone system must be a dedicated line.

GROUNDING THE UNIT
8
CU Page
Chassis Ground
Ground Rod
(+)
( )
GND
(+)
( )
GND
(+)
( )
GND
(+)
( )
GND
DOOR NO
DOOR NC
DOOR C
GATE NO
GATE NC
GATE C
12V
AC DC
GATE
RELAY
DOOR
RELAY
POWER
POWER
INPUT
GND
INPUT
VCR NO
VCR C
TEL
L NE
TIP
R NG
RS 485 (1)
RS 485 (2)
RS 485 (3)
RS 485 (4)
GATE
RELAY
DOOR
RELAY
CHASSIS
GROUND
POSTAL/EXIT
SW INPUT
VCR
RELAY
It is MANDATORY that this unit is properly
grounded. The provided "chassis ground" wire
must be connected to the ground rod. If unit is
not grounded, lightning damage will occur.
Please refer to the owners manual for proper
grounding instructions.
MADE N USAeliteentryphone com
Refer to the next page for ground rod installation.
It is MANDATORY that this unit is properly
grounded. The provided "chassis ground" wire
must be connected to the ground rod. If unit is not
grounded, lightning damage will occur.

EARTH GROUND ROD INSTALLATION
9
CU Page
The earth ground rod must be located within
3 feet from the Elite Entry Phone System.
The ground wire must be a single, whole piece of
wire. Never splice two wires for the ground wire.
If you should cut the ground wire too short,
break it, or destroy its integrity, replace it with a
single wire length.
Chamberlain Elite Entry Phone is not
responsible for improper installation or
failure to comply with all necessary local
building codes.
To the “Chassis Ground” of Chamberlain Elite Entry Phone System
For the correct wire gauge,
consult the local code
For the correct depth
consult the local code
For the correct diameter, consult the local code
Proper grounding gives an electrical charge, such as from an electrical static discharge or a near lightning strike, a path from
which to dissipate its energy safely into the earth.
Without this path, the intense energy generated by lightning could be directed towards the Elite Entry Phone System. Although
nothing can absorb the tremendous power of a direct lightning strike, proper grounding can protect the Entry Phone System in
most cases.
The type and length of earth ground rods vary by region. Contact the building inspector’s office in the municipality where you
plan to install the unit for correct grounding materials and installation procedures.
Before digging, contact local underground utility locating companies.
Avoid damaging gas, power, or other underground utility lines.

10
CU Page
BASIC WIRING DIAGRAM
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
DOOR-NO
DOOR-NC
DOOR-C
GATE-NO
GATE-NC
GATE-C
12V
AC/DC POWER
INPUT
GND
INPUT
VCR-NO
VCR-C
TEL
LINE
TIP
RING
RS-485 (1)
RS-485 (2)
RS-485 (3)
RS-485 (4)
GATE
RELAY
DOOR
RELAY
CHASSIS
GROUND
POSTAL/EXIT
SW INPUT
VCR
RELAY
It is MANDATORY that this unit is properly
d d The provid
Pedestrian Gate
Vehicular Gate
Entry Door
Conduit
Conduit
Maglock
MaglockSolenoid
Access Door
OROR
Master Gate Operator
(Strike Open Input)
Connect two wires to the main vehicular gate operator or
door. The gate relay will be activated by either Gate 7-day
timer or ElitePro remote programming software.
Connect two wires to the secondary gate or door. The door
relay will be activated by either Door 7-day timer or
ElitePro remote programming software.
24 AWG
22 AWG
20 AWG
18 AWG
16 AWG
85 Ft
140 Ft
225 Ft
350 Ft
560 Ft
12 VAC
(50 VA)
Maximum
Distance
Wire
Gauge
RING
TIP
Entry 2 Door Relay Terminal Connection
Entry 1 Gate Relay Terminal Connection
Removable Screw Terminal
Connectors for Easy Wiring.
POWER IN
12V
AC/DC
Polarity does not matter
Processor Transformer
12 VAC (50VA) Provided
Use 18 AWG wire where possible
Telephone Line: MUST be a dedicated line for the phone system ONLY!
NOTE: Installation where fiber optic cables are present may
require additional modifications from your telephone provider.
Contact your provider for more
information.

11
CU Page
RS-485 MULTIPLE CONNECTION CONFIGURATIONS
• Up to 31 RS-485 devices supported
• Maximum distance from the last RS-485 device to the Entry Phone is 4000 Ft.
• Turn “ON” the terminator switch ONLY for the last device installed in the RS-485 line.
• Use 22 AWG twisted pair shielded wire
Each RS-485 device must have a unique “Device ID Number” set by using the rotary switches on the device. (Refer to specific RS-485 Instruction sheets).
Each RS-485 device must have a unique “Device ID Number” set by using the rotary switches on the device. (Refer to specific RS-485 Instruction sheets).
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
Turn Terminator Switch “ON”
for Last Device on Wire Run
“Daisy Chain” wiring configuration
(Recommended method for superior data transmission)
“Star” wiring configuration
• Maximum number of wire runs allowed is 7
• Maximum distance from the last RS-485 device
(per wire run) to the Entry Phone is 4000 Ft.
• Maximum number of RS-485
devices present on ALL wire runs
is 31.
• Use 22 AWG twisted pair shielded wire
Wire Run
Configuration #1
Configuration #2
4000 Ft Max.
4000 Ft Max.
+
–Gnd
+
–
Gnd

RS-485 DAISY CHAIN CONNECTION EXAMPLE
“Preferred Method”
12
CU Page
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
DOOR-NO
DOOR-NC
DOOR-C
GATE-NO
GATE-NC
GATE-C
12V
AC/DC
GATE
RELAY
DOOR
RELAY
POWER
POWER
INPUT
GND
INPUT
VCR-NO
VCR-C
TEL
LINE
TIP
RING
RS485 (1)
RS485 (2)
RS485 (3)
RS485 (4)
GATE
RELAY
DOOR
RELAY
CHASSIS
GROUND
POSTAL/EXIT
SW INPUT
VCR
RELAY
It is MANDATORY that this unit is properly
grounded. The provided "chassis ground" wire
must be connected to the ground rod. If unit is
not grounded, lightning damage will occur.
Please refer to the owners manual for proper
grounding instructions.
MADE IN USAeliteentryphone.com
RS485 Card Release Button
Main M Card Slot
RS485 Memory Card Slot
NOTE: To support RS485 devices you must insert the RF
communicator card in the RS485 memory card slot
BEFORE turning on the processor.
Elite Entry Phone
COMMUNICATOR CARD
Remote Access RS-485
capacity
Card Reader
RS485 Remote
Device 3
Stand-Alone Receiver
RS485 Remote
Device 2
Universal Interface Board
RS485 Remote
Last Device
Keypad
RS485 Remote
Device 1
Ground
(+)
(-)
Use 22 AWG Twisted Pair Shielded Wire

RS-485 STAR CONNECTION EXAMPLE
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
(+)
(-)
GND
DOOR-NO
DOOR-NC
DOOR-C
GATE-NO
GATE-NC
GATE-C
12V
AC/DC
GATE
RELAY
DOOR
RELAY
POWER
POWER
INPUT
GND
INPUT
VCR-NO
VCR-C
TEL
LINE
TIP
RING
RS485 (1)
RS485 (2)
RS485 (3)
RS485 (4)
GATE
RELAY
DOOR
RELAY
CHASSIS
GROUND
POSTAL/EXIT
SW INPUT
VCR
RELAY
It is MANDATORY that this unit is properly
grounded. The provided "chassis ground" wire
must be connected to the ground rod. If unit is
not grounded, lightning damage will occur.
Please refer to the owners manual for proper
grounding instructions.
MADE IN USAeliteentryphone.com
RS485 Card Release Button
Main M ard Slot
RS485 Memory Card Slot
NOTE: To support RS485 devices you must insert
the RF communicator card in the RS485 memory
card slot BEFORE turning on the processor.
Elite Entry Phone
COMMUNICATOR CARD
Remote Access RS-485
capacity
Ground
(+)
(-)
Ground
(+)
(-)
Ground
(+)
(-)
Ground
(+)
(-)
Use 22 AWG Twisted Pair Shielded Wire
Card Reader
RS485 Remote
Device 4
Stand-Alone Receiver
RS485 Remote
Device 2
Universal Interface Board
RS485 Remote
Device 3
Keypad
RS485 Remote
Device 1
13
CU Page

Push Button
Card Pops
Out
14
CU Page
MEMORY CARD INSTALLATION
Card Release Button
Card Release Button
Main Memory Card Slot
RS 485 Memory Card Slot
A. Turn power on and insert
Memory Card into Main Memo-
ry Card Slot (fig a.) Push it all
the way in until card “snaps”
into place and the card release
button pops up. The screen
should display the “Welcome
Screen” (fig b.)
A. To view the memory capacity of the system or to view
the software version currently running on the system in
operation an information screen is accessible on all Dial
Code systems for easy reference. Turn power off and insert
memory card in main memory card slot. Turn power on and
the information screen should display as seen in (fig e.)
B. If the screen continues to display
the “Insert Memory Card” screen
(fig c.) then eject memory card by
pressing the corresponding card
release button down and reinsert
memory card into main memory card
slot (fig d.). Otherwise continue with
programming.
Welcome To
Elite Entry Phone
Insert Memory Card
IN MAIN SLOT
MEMORY CAPACITY
SOFTWARE VERSION NUMBER
(fig a.)
(fig b.)
(fig c.)
DIAL CODE LC-250
REV. 1.00_
(fig e.)
VIEWING THE SOFTWARE VERSION
(fig d.)

WARNINGS AND PRECAUTIONS
15
CU Page
250
500
The Entry Phone is only water resistant when the Stainless Steel
Door is closed and locked. Do not expose the Processor Unit or the
open Processor Containment Box to rain, snow, or harsh weather
conditions. Do not drop the Processor or expose it to impact.
Do not touch the terminals on the RAM Cards.
Do not bend, drop or expose to impact.
CVBNM
’
X
Z
A
QWERTYUI
0
7
4
123
56
89
OP
SDFGHJKL
SPACE BAR
EXIT HELP
PROGRAM
ERASE ENTER
BACK
SPACE
SH FT

16
CU Page
PROGRAMMING THE PROCESSOR
ENTERING THE PROGRAM MODE
When the Processor unit is turned on and the button is pressed, the screen will display:
If you enter the wrong password, the screen will prompt you to try again:
Press to retry entering your password. Press to quit the programming menu.
TO ENTER PROG MODE,
Type Password >____
Type in the factory present password (7777). Press . The Program Selection Screen
will display:
SELECT PROG MODE:
(N)Names (U)Utility
INVALID PASSWORD
(R)Retry (EXIT)Quit
R
Pressing the button will provide users with a help message.

SELECTING A PROGRAM MODE
17
CU Page
SELECT PROG MODE:
(N)Names (U)Utility
SELECT PROG MODE:
(P)Password
SELECT PROG MODE:
(C)Clock/Timer
SELECT PROG MODE:
(S)Strike Time
*We recommend you customize your password to avoid unauthorized programming (page 21)
To select a Program Mode, press the corresponding letter from one of the nine options.
LIST OF PROGRAM MODES:
Names
Utility
Password*
Clock/Timer
Strike Time
Page 18-19
Page 20
Page 21
Page 22-24
Page 25
Program Names or Transmitter/Card Reader
Program or edit Utility Codes
Program New Password ( recommended )
Program System Clock and Seven Day Timers
Program relay Output Time ( for 2 relays )
1
2
3
4
5
N
U
P
C
S
Use the keys to scroll through the five different Program Modes.
Pressing the button will provide users with a help message.
IMPORTANT NOTE: While in the help screens, programming will be disabled.
To continue programming, press the button to exit the help screens first.

18
CU Page
RESIDENT INFORMATION
SELECT PROG MODE:
(N)Names (U)Utility
PROG A NEW NAME N
PROG BY CODE:___
In the Program Selection Screen (fig a.), Press the key. The screen will display (fig b.):
You now have three options:
Resident name
Resident code
OR OR
STEP N
1
STEP 2
Type in the desired Resident name, LAST name first, followed by the first name (fig c.). If the code you have
selected is already used, there will be a name already. You can edit the name by simply typing over it.
Press the key to complete the entry. You may also use the keys to move the cursor
within a code.
STEP 3
Type in any seven numbers to fill the phone number field (fig d.). This field is not used but must be completed.
Press the key to complete the entry. The Key Code screen will be displayed.
STEP 4
To program by name, press
the key and the first
empty code will display.
N
To program by code, enter
a three digit code* and press
the key.
Assignment of Resident Key Codes are optional. The first three digits of the Key Code is the assigned Directo-
ry Code. Assign the last three digits (numeric characters only) to create an individual Key Code. If using the RF
Card, proceed to Step 6 (fig e). Press the key.
STEP 5
To view or edit an existing name
or code, use the
keys to scroll through Directory.
(fig a.)
(example - fig c.) (example - fig d.)
(example - fig e.)
(fig b.)
005 LastNAME,First
Jones, Robert_
005 KEY CODE:
005123
005 PHONE NUMBER:
___-_-111-1111
An individual six digit Resident Key code may be
assigned to each resident . Tenants can use
their Key Code to access the premises.
The unit will only accept codes within it’s
range - depending on memory capacity.
*

TRANSMITTER/CARD READER PROGRAMMING
19
CU Page
STEP 6
005 TRANSM/CARD#1:
___-_____ (S) SCAN
To complete entry, press the key to return to the program selection screen.
To program RF devices ( i.e. transmitters/cards etc.) continue on to Step 7.
Use keys to view and
program up to 10 transmitter or card
codes associated to the directory code.
To program a transmitter or card code
you may enter the code manually using
the keypad or you may scan the
transmitter/card code.
NOTE: To enable the transmitter/card programming feature, you must insert the communicator card in the
“RS-485 memory card slot” slot beforeyou turn on unit. (refer to “Memory Card Installation” section)
005 TRANSM/CARD#2:
___-_____ (S) SCAN
005 TRANSM/CARD#10:
___-_____ (S) SCAN
•
•
STEP 7
Repeat steps 7 and 8 for up to ten devices per directory code. After the last device has been programmed,
press or key to return to the program selection screen.
STEP 9
NOTE: The time zones and restrictions associated with transmitter/card codes can only be programmed
remotely using the EMS modem software. Unassigned transmitter/card codes can only be programmed
remotely using the EMS modem software.
STEP 8
CVBNM’
X
Z
A
Q W ERT Y U I
0
7
4
123
5 6
89
OP
SD F G H J K L
SPACE BAR
EX T HELP
PROG AM
ERASE ENTER
BACK
SPACE
SH FT
STAND-ALONE
RECEIVER
Model ERRB 485
Processor
Touch the card to the card reader
to activate remote device
Model ECR-485B
Press button on transmitter to activate remote device
(fig a.)
(fig b.)
To scan a card code, press the
key and activate the card as shown in
fig a.
To scan a transmitter code, press the
key and activate the transmit-
ter as shown in fig b.
S
S