Chamberlain SECURITY+ WPB3LM3 User manual

Carton Inventory
Overview
The Wireless 3-Button Control Station is designed to
be used only with the Wireless 3-Button Radio
Receiver (not provided).
1
Control Station
Model WPB3LM3
Wireless 3-Button Control Station
Bolt (4)
Washer (4)
Nut (4)
Screw (4)
Allen Wrench
Assembly
Install 4 AA Alkaline batteries (not provided). (Lithium
batteries recommended for colder environments.)
Learn
Button
Dipswitch
Block
®
Your WPB3LM3 can also be programmed to operate
as a 3-button wireless control station: The green
button will open the door, the white button will close
the door and the red button will stop the door's
movement. This feature may be setup as follows:
1. To enter programming press the RADIO button on
the logic board (the RADIO LED will light).
2. To program the OPEN button to the WPB3LM3
press OPEN on the logic board. The RADIO LED
will flash and then stay on. Press the green button
on the WPB3LM3 and the RADIO LED on the logic
board should flash. The WPB3LM3 should now be
programmed. (By programming the WPB3LM3 you
use 1 channel of the 23 channels on the radio
receiver.)
3. To program the CLOSE button to the WPB3LM3
press CLOSE on the logic board. The RADIO LED
will flash and then stay on. Press the white button
on the WPB3LM3 and the RADIO LED on the logic
board should flash. The WPB3LM3 should now be
programmed. (By programming the WPB3LM3 you
use 1 channel of the 23 channels on the radio
receiver.)
4. To program the STOP button to the WPB3LM3
press STOP on the logic board. The RADIO LED
will flash and then stay on. Press the red button on
the WPB3LM3 and the RADIO LED on the logic
board should flash. The WPB3LM3 should now be
programmed. (By programming the WPB3LM3 you
use 1 channel of the 23 channels on the radio
receiver.)
5. After programming the WPB3LM3 press the
RADIO button on the logic board (LED will turn off).
NOTE: If there is no activity within 30 seconds the
radio will automatically exit programming mode.
Programming WPB3LM3 to a
Commercial Logic 3 Operator
Operation
Clear Memory of Receiver: When the Receiver has
power, press the Learn button until the LED blinks a
total of 6 times.

Mount Control Station
Step 1
Choose mounting location for Control Station. Remove
the back panel and attach it to a solid surface or post.
Mount the Control Station onto the back panel with
screws. Tighten screws with Allen wrench.
Step 2
It is recommended that the Control Station be
mounted to a Gooseneck post or non-metallic
surface.
Refer to Receiver manual for mounting instructions.
© 2011, The Chamberlain Group Inc.
114A3539D All Rights Reserved
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited,
except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-2806
www.liftmaster.com
The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that it is free from defect in materials and/or workmanship for a period
of 1 year from the date of purchase.
One Year Limited Warranty