Chamberlain GH User manual

Operator Mounting
Wall Mount: The operator should generally be installed below the door shaft, and
as close to the door as possible.
Bracket Shelf Mounting: The operator may be mounted either above or below the
door shaft.
NOTE: The optimum distance between the door shaft and operator drive shaft is
between 12 - 15 inches.
Place door sprocket on the door shaft. Do not insert the key at this time.
Place drive sprocket on the appropriate side of the operator.
Do not insert the key at this time.
Wrap chain drive around door sprocket and join roller chain ends together with
master link.
Raise operator to approximate mounting position and position chain over operator
sprocket.
Raise or lower operator until the chain is taut (not tight). Make sure the operator
output shaft is parallel to door shaft and sprockets are aligned. When in position,
secure the operator to wall or mounting bracket.
Align sprockets, insert key into keyway, and secure.
Place hand chain around hand chain wheel.
Run the power wires through the power wiring conduit hole in the electrical box
enclosure. Connect the power to the operator. Connect the earth ground to the
ground screw in the electrical box enclosure. Follow ALL local electrical codes.
Adjust the limit switches to open and close door properly. Make sure the limit nuts
are positioned between the limit switches before proceeding with adjustments.
Radio programming and troubleshooting instructions inside cover of operator.
1b
1a
2
3
4
5
6
7
8
9
10
11
Align Sprockets
7
Inside the Electrical Box
Limit Switches
CLOSE
OPEN
SAFETY
Direction Limit Nut Will Move During Travel
Retaining
Plate
Push
Limit Nuts
POWER WIRING
USE COPPER WIRE ONLY
L1 L2
Single Phase Connections
9
14 AWG Minimum
Follow ALL national
and local electrical codes.
Power wiring ONLY!
Turn off power
to the operator
BEFORE manually
operating your door.
Be sure door
sprocket is properly
aligned with drive
before securing to
the shaft.
Chain Keeper
(4' above floor)
10
Optimum Distance
12" - 15"
Right Hand Wall Mounted Operator
1a Bracket Shelf Mounted Operator 1b
This operator has provisions for manually operating the door in case
of emergency or power failure. These operators are equipped with a
manual hoist. An electrical interlock will disable the electrical controls
when the hoist is used. Turn off power to the operator BEFORE
manually operating your door.
To operate the hoist, pull the disconnect chain (small chain) to
engage the hoist mechanism. The disconnect chain may be locked
in position by slipping the end through the keyhole of the chain
keeper mounted on the wall. Operate the door in the desired
direction by pulling on one side or the other of the continuous loop
hoist chain (large chain). The disconnect chain must be released
from the chain keeper before the door will operate again electrically.
Manual Operation
Electrical Interlock with Hoist
Electrical Interlock with Hoist
QuickStartforthemodelGHdooroperator
Chain Keeper
(with pad locking provisions)
Mount Chain
Keeper 4'
above floor
OPTIONAL
Mounting Bracket
P/N 08-9098
Optimum
Distance
12" - 15"
LOGIC 4
HOT
HOT
NEUTRAL EARTH
IMPORTANT: This QuickStart is intended to highlight a typical installation. These instructions are not intended to be comprehensive. Since each application is unique, it is the responsibility of
the purchaser, designer, installer and end user to ensure that the total door system is safe for its intended use. Please consult the manual and/or a qualified technician for further information.
POWER WIRING
USE COPPER WIRE ONLY
L1 L2
DEDICATED
CIRCUIT
Three Phase Connections
L3
DEDICATED CIRCUIT

LiftMaster Monitored Entrapment Protection (LMEP)
is required for most programmable settings.
Thru-Beam Photoelectric Sensors (Shown)
OPEN
CLOSE
STOP
Half the Height of the Door
NEVER run Control wiring
in same conduit as the
Power wiring!
Edge Sensor
Approximately 5 Feet
6" max
above the
floor
White/Black
White
Push and Release to Open
(without Mid Stop programming)
Push and Release to Stop
Push and Hold to Close
CONTROL WIRING
USE COPPER WIRE ONLY
E2
TTS
FSTS
DIAG
PROG
D1
C2
B2
Factory Setting is C2
Board Selector Dial
TIMERMIDMRT
TIMERMIDMRT
E2
TTS
FSTS
DIAG
PROG
D1
B2
C2
OPEN Mid Stop Programming
1. Close the Door.
6. Turn selector back to selected wiring type.
3. Press and release the MID button.
2. Turn selector to PROG.
OPEN
CLOSE
STOP
D20
D21
D13
11
11
9
8
20 AWG or Greater
24VAC 24VAC Timer Defeat Common MAS
Maintenance Alert LED
LMEP Edge Open Close Stop Common SBC
141 2 3 4 5 6 7 8 9 10 11 12 13
7
6
5 4
4
4
10
The OPEN LED will flash once for every 1 sec.
The CLOSE LED will flash once for every 15 sec.
Timer-to-Close Programming
Timer automatically closes door after a preset time.
1. Close the Door.
5. Press and release the OPEN button once for every 1 second.
Press and release the CLOSE button once for every 15 seconds.
TIMERMIDMRT
3. Press and release the TIMER button.
TIMERMIDMRT
6. Press and release the TIMER button to complete programming.
2. Turn selector to PROG.
4. Press and release the STOP button to clear the timer.
OPEN
CLOSE
STOP
D20
D21
D13
Example:
Push CLOSE +Push OPEN +Push OPEN =17 seconds total
(15 seconds) (1 second) (1 second)
OPEN
CLOSE
STOP
D20
D21
D13
© 2010, The Chamberlain Group Inc.
All Rights Reserved
01-35245
The mid stop feature is to open the door to a preset point prior to the fully open position.
E2
TTS
FSTS
DIAG
PROG
D1
B2
C2
8. Turn the selector dial back
to the desired wiring type.
MAS Programming (Maintenance Alert System)
MAS
6. Press the OPEN button once for
every 5,000 Cycles increments.
Press the CLOSE button once for
every 3 Month increments.
Press the STOP button once to
Clear the MAS Setting.
OPEN
CLOSE
STOP
D20
D21
D13
2. Close the Door.
1. The MAS assists the installing dealer in setting
up a routine maintenance program. Once
programmed, the MAS notifies the end user
(with a flashing LED on the 3 button station)
when a preset number of cycles/months has
elapsed and scheduled maintenance is due.
4. Press and release the MAS button.
5. Press the STOP button once
to clear the MAS counter.
3. Turn the selector dial
to PROG.
MAS
OPEN
CLOSE
STOP
D20
D21
D13
OPEN
CLOSE
STOP
D20
D21
D13
OPEN
CLOSE
STOP
D20
D21
D13
7. Turn selector to T, TS or FSTS wiring types.
Follow ALL national and local electrical codes
OPTN
OPTN
OPTN
E2
TTS
FSTS
DIAG
PROG
D1
B2
C2 OPTN
E2
TTS
FSTS
DIAG
PROG
D1
B2
C2 OPTN
E2
TTS
FSTS
DIAG
PROG
D1
B2
C2 OPTN
E2
TTS FSTS
DIAG
PROG
D1
B2
C2 OPTN
7. Press the MAS button to
complete the programming.
The on board LED will flash back
the programmed settings. The
OPEN LED will flash once for every
5,000 cycles. The CLOSE LED will
flash once for every 3 months.
4. Press the OPEN button, wait until the door reaches the desired
mid stop height, then press and release the STOP button.
5. Press and release the MID button to complete programming.
NOTE: Must have at least one LiftMaster
Monitored Entrapment Protection (LMEP)
device installed.