Chamberlain Elite EL25N User manual

Telephone entry/access control system
© 2008 The Chamberlain Group, Inc.
All Rights Reserved
®
™
®
™
Installation Manual for
Installation Manual for
EL MODELS
EL MODELS
For more information visit www.devancocanada.com

Table of Contents
Page 1
Mounting the Unit Page
Dimensions 2
EL25 Installation 3
Rotating the Keypad for Vertical Mounting 3
Unlocking/Locking EL2000 4
EL2000 Installation 5
Wire Type
Wire Connections to Unit (Factory Settings for Relays) 6
Wire Specs and Run Distances 7
Power Wire Specs and Run Distances 7
Grounding the Unit
Grounding the Unit 8
Phone Lines
Wiring 1 Unit to Telco Line 9
Wiring Multiple Units to Telco Line 10
Wiring with No Telco Line 11
Wiring to Dedicated Telco Line 12
Wiring to an Internal Phone System 13
Connection to an NPBI System 14
External Devices
Wiring a Door Strike Lock 15
Wiring a Maglock 15
Wiring a Gate Operator 16
Wiring a Key Switch/PIR/REX 16
Wiring a Door Sensing Device 17
Wiring the AutoCall Feature 17
Wiring a Radio Frequency Module 18
Wiegand Card Reader / Keypad 18
Wiring a Postal Lock Switch 19
Wiring an Internal Camera (CCTV) 19
Power
Wiring Power to the Unit 20
Powering up and Checking the LEDs 20-21
Troubleshooting 22
Repair Parts
Repair Parts 23-24
“Your” Set-Up
“Your” System Diagram and Wiring Configuration 25-26
Accessories 27
FCC and DOC
FCC and DOC Requirements 28

Page 2
Dimensions
Dimensions
Caution! A Static Discharge can Damage Circuit Boards
6 in.
3-15/16 in.
Mounting Holes (4)
for 5/16 in.
3/4 in. Conduit Hole
1-1/4 in. Conduit Hole
Knockouts for 5/16 in.
Knockouts for 3/8 in.
15 in.
AUG 10, 2005
WELCOME
3-1/16 in.
9 in.
1-5/8 in. 2 in.
12 in.
7 in.
9-1/2 in.
6 in.
3-1/16 in.
1-1/2 in. 1/2 in.
EL2000 Units
EL25 Units

Page 3
EL25 Installation
EL25 Installation
DO NOT overload the removable
terminal block connectors.
One wire per hole.
DO NOT pinch wires when
closing and locking the unit.
Rotating the Keypad for Vertical Mounting
Screw
Notch
12
3
Bracket
Keypad
Main Circuit
Board
Main Circuit Board Connections
J200 - Speaker
J402 - Light
J404 - Call Button Board
ONLY Vertical
Mounting Position
J401 - Keypad
J406 - Light
J201 - Microphone
NOTE: Bracket notch lines up
with ribbon cable on keypad.
Caution! A Static Discharge can
Damage Circuit Boards For EL25 ONLY
Caution! A Static Discharge can Damage Circuit Boards
1Unlock Unit 2Carefully Lift Cover Up
then Slide Out on Hinges
3Unplug the 2 Main Harnesses
4Line up Notch with
Screw and Push
Hinge Out
5Remove Back Mounting Plate from Cover
1Disconnect all Plugs from Main Circuit Board and
Remove Board. (4 Screws)
2Remove Bracket. (4 Screws)
3Rotate Keypad 90 Degrees Clockwise.
4Reverse the Sequence to Reassemble Unit.
NOTE: This unit is for surface mount applications only.

Page 4
Unlocking/Locking EL2000
Unlocking EL2000
1. Apply pressure to
the right-side of the
unit.
2. While maintaining
pressure, turn key
clockwise
3. Open cover
Locking EL2000
1. Turn key counter clockwise to lock
position
2. Close cover
3. Apply pressure to left-side until you
hear a “click” sound
4. Apply pressure to right-side of unit
until you hear a “click” sound
#
#
1
23
?
456
789
*
0#
#
#
#
#
#
#
1
23
456
789
0
*
#
?
#
#
#
#
#
#
#
#
#
#
1
23
456
789
0
*
#
?
#
#
#
#
#
1
23
456
789
0
*
#
?
#
#
#
#
#
#
#
#
#
1
23
?
456
789
*
0#
23
2
1
3
#
#
#
1
23
?
456
789
*
0#
#
#
#
#
#
#
#
#
1
23
?
456
789
*
0#
#
#
#
#
#
4
1

Page 5
#
1
23
?
456
789
*
0#
#
#
#
#
#
1
23
456
789
0
*
#
?
#
#
#
#
#
EL2000 Model Installation
EL2000 Installation
1Unlock Unit 2Open Cover
3Unplug the 2 Main Harnesses (Optional)
4Slide Front Cover Out of
Hinges (Optional)
6Mount Back Housing
to Wall or Pedestal
5Knock-out Desired
Mounting Plugs
Using Punch
NOTE: This unit is for surface and recessed mount ONLY.

Page 6
Wire Connections to the Unit
Input Board Connections
1. Door 1 Exit Request and Door Status
2. Door 2 Exit Request and Door Status
3. Door 3 Exit Request and Door Status
4. Door 4 Exit Request and Door Status
5. Postal Lock Input
6. AutoCall Input
7. Power 12 VAC Input
Output Board Connections
8. Resident Tip/Ring
9. Telco Tip/Ring
10. Relay 4, NO, NC, COM
11. Relay 3, NO, NC, COM
12. Relay 2, NO, NC, COM
13. Relay 1, NO, NC, COM
NOTE: All relays are factory set to “Strike”
and “10 sec.”
DO NOT overload the removable
terminal block connectors. One wire
per hole.
20-Pin
to Main Board 14-Pin
to Main Board
IO Output Board
IO Input Board
J2
J3
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
8
9
DOOR
STAT 4
EXIT
REQ 4
COM 4
3
2
1
5
6
7
10
11
12
13
DOOR
STAT 3
EXIT
REQ 3
COM
DOOR
STAT 4
EXIT
REQ 2
COM
DOOR
STAT 1
EXIT
REQ 1
COM
J5
J7
J6
J4
POSTAL
AUTO
J1
POWER
12VAC/DC
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Wire Connections to the Unit

Page 7
Wire Specs and Run Distances
Wire Specs and Run Distances
Use this chart to pull wires in preparation of your installation:
Power Wire Specs and Run Distances
Description of Wire Run
Grounding the Chassis
Residence and Telco Phone Lines
Door Strike
Magnetic Lock
Dry Contact Closure (Most Gate Operators)
Exit Request (REX) / Auxiliary Open Devices
AutoCall
Door Status Sensor
Barium Ferrite and Wiegand Readers
Proximity Readers
Radio Frequency Module (RF)
Postal Lock
CCTV Camera (Optional)
Wire Specification
12 AWG Copper
2 Twisted Pairs
18-24 AWG Shielded
2-Conductor
18-22 AWG Shielded
2-Conductor
18-22 AWG Shielded
2-Conductor
18-24 AWG Shielded
2-Conductor
18-24 AWG Shielded
2-Conductor
18-24 AWG Shielded
2-Conductor
18-24 AWG Shielded
5-Conductor
18-24 AWG Shielded
5-Conductor
22 AWG Shielded
RG-6 Coaxial
75 ohm
2-Conductor
18-24 AWG Shielded
Single Conductor
RG-59u Coaxial
Maximum Distance
12 feet
5000 feet*
500 feet
500 feet
100 feet
1000 feet
(Monitor with a .25 volt
p-p composite signal
sensitivity)
Page
8
9-14
15
15
16
16
17
17
18
18
18
19
19
NOTE: Use metal conduit - run wires in metal conduit instead of PVC pipe. Wires run in PVC conduit may
experience interference. Metal conduits also add extra protection against lightning strikes.
Never run Telco Wires and High Voltage wires in the same conduit. The high voltage may interfere with the Telco
Wires, possibly causing the system to malfunction.
* Total distance from Telco to residence regardless of number of units in chain.
Distance
Under 30 Feet
30 - 75 Feet
75 - 250 Feet
12 VAC Power (Included)
2-Conductor Shielded
14 AWG
14 AWG
14 AWG
12 VDC Power (Not Provided)
2-Conductor Shielded
14 AWG
14 AWG
N/A
Always provide power from a dedicated source. Plug provided transformer into an outlet wired to its own 10 AMP
minimum circuit breaker. This will prevent two problems:
• Other equipment cannot introduce spikes, noise, surges or dips into the power circuit that will affect the system.
• The system’s operation will not be affected if any other equipment develops a short circuit across the power line.
CAUTION: Not responsible for conflicts between the information listed in the above table and the requirements of
your local building codes. The information is for suggested use only. Check your local codes before installation.

Page 8
Grounding the Units
Grounding the Units
Ensure that the system is grounded properly. The units contain a number of static sensitive components that can
be damaged by static discharge.
IMPORTANT: An Earth Ground Rod is Strongly
Recommended and should be no further than 12
feet from the unit and use a minimum of 12
gauge wire in most cases. The type and length of
earth ground rods vary by region. Contact the
building inspector’s office in the municipality
where you plan to install the unit for correct
grounding materials and installation
procedures.
Other Ground Sources
within 12 ft of Unit
Green Ground
Wire
Earth Ground Rod
Ground to
Existing
Electrical
System
Electrical
Panel
Ground to
Metallic Cold
Water Pipe
12 ft Maximum
12 AGW Minimum
1
2
3
4
5
6
7
8
9
AUG 10, 2005
WELCOME
1
2
3
4
10
11
5
6
7
8
9
10
12
11
OR
NOTE: Keep ground wire as
straight as possible.
Before digging, contact your local
utility companies, to avoid
damaging gas, power, or other
underground utility lines.
DO NOT ground the units to a
pedestal post (gooseneck) if
one is used.

Page 9
Wiring 1 Unit to Telco Line
Wiring 1 Unit to Telco Line
The bypass board allows the unit to be disconnected without interrupting normal telephone operation.
NOTE: Installation where fiber optic phone lines are present may require additional modifications from your
telephone provider. Contact your provider for more information.
• When the unit is in use, the bypass switch must be set to the operate position.
• When the unit is disconnected, the bypass switch must be set to the bypass position.
Tip
Ring
Tip
Ring
OPERATE BYPASS
Ring
HOME
Tip Ring
TELCO
Tip
SYSTEM
Bypass Board
(Mount in the House)
(NOT Provided)
Ring
Tip Ring
Tip
Home Phone
Alarm System Position
Use 18-24 AWG
2 twisted pair
NOTE: If the unit will be used in
conjunction with an alarm system, you
MUST connect the telephone line to the
alarm system first. If the units are not
connected in this order, they will not
operate properly.
4
4 3 2 1
3
2
1
Output Board
(See page 6)
Telco Entrance Box
Demarcation Point
DO NOT overload the removable
terminal block connectors. One
wire per hole.
IMPORTANT: The Bypass
Board (located inside the
property) allows access to
the phone in case the unit
fails.
Never run Telco wires and High
Voltage wires in the same
conduit. The high voltage wires
may interfere with the Telco
wires, possibly causing the
system to malfunction.
RES
TELCO

Page 10
Wiring Multiple Units to Telco Line
Wiring Multiple Units to Telco Line
Up to 7 units can share the same phone line. The bypass boards allow the units to be disconnected without
interrupting normal telephone operation.
NOTE: Installation where fiber optic phone lines are present may require additional modifications from your
telephone provider. Contact your provider for more information.
• When the units are in use, the bypass switches must be set to the operate position.
• When the units are disconnected, the bypass switches must be set to the bypass position.
Tip
Ring
Tip
Ring
RES
TELCO
Tip
Ring
Tip
Ring
RES
TELCO
OPERATE BYPASS
Ring
HOME
Tip Ring
TELCO
Tip
SYSTEM
4 3 2 1
BYPASS
Ring
TELCO
Tip
Bypass Board for Unit 1 Bypass Board for Unit 2
Ring Ring
Ring
Tip Tip
Tip
Ring
Tip
Use 18-24 AWG
2 twisted pair
IMPORTANT: You must program the unit ID's
for each unit wired in the series. See Keypad
Programming Manual.
OPERATE BYPASS
Ring
HOME
Tip Ring
TELCO
Tip
SYSTEM
4
3
2
1
Last Bypass Board
4
3
2
1
Home Phone
Unit ID 1
Output Board
(See page 6)
Telco Entrance Box
Demarcation Point
DO NOT overload the removable
terminal block connectors. One wire
per hole.
IMPORTANT: The Bypass
Boards (located inside the
property) allow access to
the phone in case any of
the units fail.
Never run Telco wires and High
Voltage wires in the same
conduit. The high voltage wires
may interfere with the Telco
wires, possibly causing the
system to malfunction.
4 3 2 1
Unit ID 2
Output Board
(See page 6)

Page 11
Wiring with No Telco Line
Wiring with No Telco Line
The unit can be a stand alone system that allows communication between the unit and a resident’s phones.
Single Unit
Tip
Ring
Tip
Ring
RES
TELCO
Use 18-24 AWG
2 twisted pair
Output Board
(See page 6)
NOTE: Ringer Equivalence Number (REN) of “5” maximum.
Never run Telco wires and High
Voltage wires in the same
conduit. The high voltage wires
may interfere with the Telco
wires, possibly causing the
system to malfunction.
Multiple Units (Up to 7)
Tip
Ring
Tip
Ring
RES
TELCO
Tip
Ring
Tip
Ring
RES
TELCO
To next unit (Unit ID 3 then 4 etc.)
Use 18-24 AWG
2 twisted pair
IMPORTANT: You must program the unit ID's for each
unit wired in the series. See Keypad Programming Manual.
IMPORTANT: Only disable the Telco mode of the unit farthest
away from the house. See “Disable Telco Mode” in the
Keypad Programming Guide.
Unit ID 1
Output Board
(See page 6)
Unit ID 2
Output Board
(See page 6)
Home Phone
NOTE: Ringer Equivalence Number (REN) of “5” maximum.

Page 12
Wiring to Dedicated Telco Line
Wiring to Dedicated Telco Line
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Tip
Ring
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Tip
Ring
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Never run Telco wires and High
Voltage wires in the same
conduit. The high voltage wires
may interfere with the Telco
wires, possibly causing the
system to malfunction.
Use 18-24 AWG
2 twisted pair
IMPORTANT: You must program the Unit
ID's for each unit wired in the series. See
Keypad Programming Manual.
Unit ID 6
Output Board
(See page 6)
Unit ID 7
Output Board
(See page 6)
Use 18-24 AWG
2 twisted pair
Telco Entrance Box
Demarcation Point
Ring
Tip
Telco Entrance Box
Demarcation Point
Ring
Tip
To next unit (Unit ID 5 then
4 etc.) Unit ID 1 is farthest away
from Telco Box)
Single Unit
Multiple Units (Up to 7)
NOTE: Installation where fiber optic phone lines are present may require additional modifications from your
telephone provider. Contact your provider for more information.

Page 13
Wiring to an Internal Phone System
Wiring to an Internal Phone System
The units can be wired to any Analog Trunk in an internal home phone system.
NOTE: Installation where fiber optic phone lines are present may require additional modifications from your
telephone provider. Contact your provider for more information.
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Use 18-24 AWG
2 twisted pair
Analog
Trunk
Telco Entrance Box
Demarcation Point
Internal
Phone System
Ring
Tip
EX 1 EX 3Analog EX 42
T
R
Tip
Ring
Never run Telco wires and High
Voltage wires in the same
conduit. The high voltage wires
may interfere with the Telco
wires, possibly causing the
system to malfunction.
Single Unit
Multiple Units (Up to 7)
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Tip
Ring
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Tip
Ring
Use 18-24 AWG
2 twisted pair
IMPORTANT: You must program the unit
ID's for each unit wired in the series. See
Keypad Programming Manual.
Unit ID 6
Output Board
(See page 6)
Unit ID 7
Output Board
(See page 6)
To next unit (Unit ID 5 then
4 etc.) (Unit ID 1 is farthest away
from Telco Box)
Analog
Trunk
Telco Entrance Box
Demarcation Point Internal
Phone System
Ring
Tip
EX 1 EX 3Analog EX 42
T
R
Tip
Ring

Page 14
Connection To A NPBI System
Connection To An NPBI System
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Tip
Ring
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Tip
Ring
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Tip
Ring
Never run Telco wires and High
Voltage wires in the same
conduit. The high voltage wires
may interfere with the Telco
wires, possibly causing the
system to malfunction.
Use 18-24 AWG
2 twisted pair
IMPORTANT: You must program the Unit
ID's for each unit wired in the series. See
Keypad Programming Manual.
Unit ID 6
Output Board
(See page 6)
Unit ID 7
Output Board
(See page 6)
Use 18-24 AWG
2 twisted pair
Sentex
Ovation
Unit
To next unit (Unit ID 5 then
4 etc.) Unit ID 1 is farthest away
from Telco Box)
Sentex
Ovation
Unit
Single Unit
Multiple Units (Up to 7)

Page15
Wiring a Door Strike Lock/Maglock
Wiring a Door Strike Lock
Wiring a Maglock
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Use 18-22 AWG
NOTE: The door strike can
be connected to any of the
4 relays.
Normally Open
Common
DO NOT use the unit’s power
supply for the Door Strike.
– +
AC or DC
Power for
Door Strike
(Not Provided)
DO NOT overload
the removable
terminal block
connectors. One
wire per hole.
Output Board (See page 6)
For DC Power: Install a
1N4005 diode or equivalent.
For AC Power: Install a
Siemens S10K30 MOV
(Metal Oxide Varistor) or
equivalent.
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Output Board (See page 6)
Install a 1N4005 diode or
equivalent.
NOTE: The maglock can be
connected to any of the
4 Relays.
DO NOT use the unit’s power
supply for the Maglock.
Use 18-22 AWG
– +
Normally Closed
Common
AC or DC
Power for
Door Strike
(Not Provided)
For AC Power: Install a
Siemens S10K30 MOV
(Metal Oxide Varistor) or
equivalent.

Page 16
Wiring a Gate Operator / Key Switch / PIR / REX
Wiring a Gate Operator
Wiring a Key Switch/PIR/REX
Any auxiliary opening device such as a key switch or PIR (Passive Infrared Device), or an exit request button
(REX) that provides normally open contact closure can be hooked up to the Door Input terminals.
IO Output Board
LED 2
LED 1
RELAY 1
RELAY 2
RELAY 3
RELAY 4
J3
J5
J4
J1
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
LED 4
LED 3
RES
TELCO
J6
J8
Use 18-24 AWG
NOTE: The gate operator can be
connected to any of the 4 relays.
Normally Open
Common
DO NOT overload
the removable
terminal block
connectors. One
wire per hole.
Output Board
(See page 6)
IO Input Board
J2
J3
DOOR
STAT 4
EXIT
REQ 4
COM
DOOR
STAT 3
EXIT
REQ 3
COM
DOOR
STAT 4
EXIT
REQ 2
COM
DOOR
STAT 1
EXIT
REQ 1
COM
J5
J7
J6
J4
POSTAL
AUTO
J1
POWER
12VAC/DC
Use 18-24 AWG
NOTE: Additional opening or exit devices can be
connected to any of the 4 Exit Request inputs.
Exit Request
Common
Input Board
(See page 6)
NOTE: Refer to your gate operators owner’s manual for proper relay strike time.

Page 17
Wiring a Door Sensing Device / AutoCall
Wiring a Door Sensing Device
The units can monitor the position of up to four doors/gates and may react to a change in their status with one of
the relays (not set as a control relay). For example, if a door is pried open or is held open after its relay deactivates,
the unit will record the breach in its transactions and can perform the following actions:
• Energize a relay to activate an alarm device such as a siren, light or CCTV camera.
• Main use is to terminate strike time early.
Wiring the AutoCall Feature
Using the AutoCall feature, the unit will automatically call the main residence phone when a driveway sensor is
activated (any device that provides a contact closure). For example, when a visitor drives over a loop sensor that
is connected to the AutoCall feature, the unit will call the main residence phone automatically so the visitor can
speak to the resident without pressing the call button on the unit.
IO Input Board
J2
J3
DOOR
STAT 4
EXIT
REQ 4
COM
DOOR
STAT 3
EXIT
REQ 3
COM
DOOR
STAT 4
EXIT
REQ 2
COM
DOOR
STAT 1
EXIT
REQ 1
COM
J5
J7
J6
J4
POSTAL
AUTO
J1
POWER
12VAC/DC
Use 18-24 AWG
Door Status
Common
Input Board
(See page 6)
NOTE: Additional sensing devices can be
connected to any of the 4 Door Stat inputs.
IO Input Board
J2
J3
J5
J6
J4
POSTAL
AUTO
J1
POWER
12VAC/DC
Loop
Detector
Use
18-24 AWG
Common
In
Loop
Sensor
Input Board
(See page 6)
NOTE: Door sensing device should provide contact closure when door is closed.

Page 18
Wiring a RF Module / Card Reader / Keypad
Wiring a Radio Frequency Module
An optional radio frequency module and a remote antenna can be installed if the residents will access a
controlled area with a transmitter. Refer to instructions supplied with the optional RF Module for more
information.
Wiegand Card Reader/Keypad
Wiegand card readers and keypads can be connected to either of 2 optional Wiegand modules that can be placed
in the unit. Each Wiegand module supports two card readers/keypads. Some Wiegand card reader/keypads have
a sixth blue wire. DO NOT connect this blue wire to the unit. Insulate this wire from the unit to prevent a short
(Refer to instructions supplied with your Wiegand device for more information).
RG-6
Coaxial
Connector
RG-6 Coaxial Cable
100 Feet Maximum
Remote Antenna
Avoid any metallic
surface around the
antenna.
RF Module(s) will fit in positions
J400 (Device 1) and/or J407 (Device 3)
(4 Mounting Screws per Board are Required)
1 RF Module Kit
Part # RFMODKT
(390 MHz)
or
Part # RFMODKT3
(315 MHz)
J407 Position J400 Position
Card Reader is Wired to Device 1
P12V
P5V
DATA 0
DATA 1
LED
COM P12V
P5V
DATA 0
DATA 1
LED
COM
J1J2 J1J2
Device 1Device 3 Device 2Device 4
Red Power
Green
White
Brown
Black
Shield
(Attach to the
unit ground only).
Blue (Insulate this wire).
Use 18-24
AWG
1 Wiegand Module Kit
Part # WOMODKT
P12V
P5V
DATA 0
DATA 1
LED
COM P12V
P5V
DATA 0
DATA 1
LED
COM
Wiegand Modules will fit in
J400 as Device 1 (J1) and 2(J2)
and/or
J407 as Device 3 (J1) and 4(J2)
(4 Mounting Screws per Board are Required)
NOTE: The remote can control 1-4 doors.

Page 19
Wiring a Postal Lock Switch / Internal Camera (CCTV)
Wiring a Postal Lock Switch - EL25 Models Only
The Post Office requires installation of a postal lock if postal carriers do not have access to a controlled area.
Contact the local post office and arrange for them to install the postal lock while you are on site. The postal lock
requires a switch to activate one of the four relays (Configurable with programming number 69 , in the Keypad
Programming Manual).
Wiring an Internal Camera [CCTV]
An Optional CCTV (Close Circuit Television) camera can be installed inside the unit. Refer to instructions supplied
with the camera kit for more information.
IO Input Board
J2
J3
J5
J7
J6
J4
POSTAL
AUTO
J1
POWER
12VAC/DC
Use
18-24 AWG
Common
In N.C.
Switch
Input Board
(See page 6)
DO NOT overload the removable terminal
block connectors. One wire per hole.
RG-59u Coaxial Cable 1000 Feet Maximum
(Monitor with a .25 volt p-p composite signal sensitivity)
A Closed Circuit Monitor
Home Entertainment
System
Contact your dealer/ installer
for more information
EL2000EL25
OR
NOTE: In the EL2000 models, the postal lock switch is pre-wired.