Chamberlain Security+ 963D User manual

To Control the Opener Lights
NOTE: Feature only available on openers equipped with a
multi-function control panel.
With 315MHz Security✚®remote controls, a remote push button
can be programmed to operate the opener lights without opening
the door.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the multi-function control
panel.
3. Press and hold the Lock button on the multi-function control
panel.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
Open/Close/Stop Operation
NOTE: Feature only available on openers equipped with a
multi-function control panel.
Your 315MHz Security✚®remote control can be programmed to
operate one door using all 3 buttons: the button with one light slot
will only open the door, the button with two light slots will close
the door, and the button with three light slots will stop the door’s
movement. You may set up this feature as follows:
1. With the door closed, press
and hold the button with one
light slot.
2. Press and hold the Lock
button on the multi-function
control panel.
3. Press and hold the main door
control push button.
When the opener lights flash, release all buttons. Test by pressing
the 1 light slot button (Open) on the remote. The door should
open. Press it again while the door is open and nothing should
happen. Press the 2 light slot button (Close) while the door is
moving and it should close. Press the 3 light slot button (Stop)
and the door should stop immediately.
Model 963D Security✚®3-Button Remote Control
with Proximity Lighting Feature
OWNER’S MANUAL
®
OR
1. Press and release the “learn” button on
the motor unit. The learn indicator light
will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
3. Release the button when the motor unit light
blinks. It has learned the code. If light bulbs
are not installed, two clicks will be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor unit
until the learn indicator light goes out
(approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or
keyless entry you wish to use.
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
1 Light Slot
(Open)
2 Light Slots
(Close)
3 Light Slots
(Stop)
For use with 315MHz Security✚®garage door openers and
universal receivers that have a purple “learn” button and
315MHz gate receivers.
NOTE: To activate the remote control functions, pull out the
plastic pull tab protruding from the remote control housing.
This remote control is equipped with a proximity lighting feature.
When moving a hand within close proximity to the remote control,
the LED lights turn on for 3 seconds. Upon successful activation
of a remote control button, the LED lights will blink rapidly.
Proximity Disable Feature
The remote control will turn off the proximity lighting feature if the
proximity lighting is turned on 10 consecutive times without
activation of a button. To re-enable the proximity lighting, simply
press a button. This function conserves battery life.
To Add or Reprogram the Remote Control

The Remote Control Batteries
The 3V2016 lithium batteries for the opener and LED lights
(marked “LED and Opener Battery”) should last 5 years. The
3V2450 lithium battery for the proximity lighting (marked
“Proximity Battery”) should last 1-2 years.
To replace the batteries, remove the two screws and open the
remote control housing. Push the battery out of the holder for
removal. Insert replacement batteries positive side up (+).
Dispose of old batteries properly.
Replace the batteries with only 3V2016 or 3V2450 coin cell
batteries.
CAUTION: Do not bend spring contact. If bent, the proximity
sensor will not work.
©2007, Chamberlain Group Inc.
114A3566 All Rights Reserved
Proximity
Battery
LED and
Opener
Batteries Spring
Contact
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FOR SERVICE, DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
Replacement Parts
PART NO. DESCRIPTION QTY
10A19 3V2016 Lithium Battery: LED and Opener 2
10A33 3V2450 Lithium Battery: Proximity Switch 1
29C151 Visor Clip 1
Troubleshooting
Reduced proximity
sensing (does not
activate by touching
top of remote control)
Check if proximity lighting is disabled
by pressing a button.
Replace 3V2450 battery with same
type 3V2450 coin cell.
The Proximity Sensor may be
oversensitized. Sit remote control
undisturbed for 60 seconds on a
non-metallic surface. This allows the
sensor to recalibrate itself.
Dim LED lights Replace two 3V2016 batteries with
same type 3V2016 coin cells.
No rapid LED blinking
after pressing a button Replace two 3V2016 batteries with
same type 3V2016 coin cells.
PROBLEM SOLUTION
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2016 or 3V2450 coin batteries.
• Do NOT recharge, disassemble, heat above 212°F (100°C) or
incinerate.