Chamberlain KLIK5C-BK2 User manual

®
®
MODEL KLIK3C-BK2
MODEL KLIK3C-SS
MODEL KLIK5C-BK2
MODEL KLIK5C-SS
UNIVERSAL REMOTE CONTROL
Your remote control can be programmed to operate
up to two devices, such as a garage door opener,
gate operator, or commercial door operator and has
a SMART/ LEARN button. Each button on the remote
control works independently of the other and must
be programmed separately. The images throughout
this manual are for reference only and your product
may look different.
STOP
Read instructions thoroughly
BEFORE beginning. If you are using
this product with residential door
openers, this product must be used
only with door openers manufactured
starting January 1, 1993 that use photoelectric
sensors located near the bottom of the door track.
IMPORTANT: The remote will activate your door or
gate during programming. Be sure the door is clear
of ALL obstructions. Start with the garage door
closed. Make sure the garage door opener has a
working light because it is a programming indicator.
WARNING: This product can expose you
to chemicals including lead, which are
known to the State of California to cause
cancer or birth defects or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov

CONNECT TO THE MYQ®APP
1. Close the garage door.
IMPORTANT: The remote activates the garage
door during programming. Ensure the door is
clear of all obstructions.
2. Look for a Wi-Fi or a Powered by myQ®logo
to determine if your garage door opener is
myQ®compatible. If not, proceed to
programming.
Or
®
3. To start on monitoring the garage door
movements, scan the QR code to download
the myQ®app .
4. To add your remote and name, follow the in-
app instructions in order .
5. After completing setup in the app, you can
control the garage door opener and to receive
notices ever time your garage door opens and
closes.
GETTING STARTED
Determine if the product you are programming the
remote control to has a SMART/LEARN button or
DIP Switches. The SMART/ LEARN button or DIP
Switches are located either on the product or in an
external receiver on or near the product. The
following instructions are for a garage door opener
with a SMART/LEARN Button. For DIP Switch
programming instructions or additional help, see
support.chamberlaingroup.com.
SMART/
LEARN Button
OR

DIP Switch
NOTE: DIP Switch is only available in KLIK3Cmodels
manufactured before 11/2020.
PROGRAM TO GARAGE DOOR
OPENERS WITH A YELLOW LEARN
BUTTON
If your remote was previously programmed to
another type of opener, follow the programming
instructions on the next page to reprogram to a
yellow LEARN button.
Yellow
LEARN
Button
LED
1. Start with the garage door closed.
2. Press and immediately release the yellow
LEARN button. The Learn LED glows steady
for 30 seconds. Within 30 seconds...
3. Press and hold the button on the remote
control you wish to use.
4. Release the button when the garage door
opener lights blink or two clicks are heard.
5. Test by pressing the button you just
programmed. The opener activates.
To program the remote to Chamberlain accessories,
refer to the manual provided with the accessory.

PROGRAM TO COMPATIBLE GARAGE
DOOR OPENERS
LED
Program
Button
Cover
SMART/
LEARN
Button
1. Remove the remote control cover. Press and
hold the program button until the LED turns
on.
2. Press and release the SMART/ LEARN button
on your garage door opener.
3. Select a button to program on the remote
control. Press and release the button the
specified number of times according to the
following chart. NOTE: Make sure the LED
stops flashing between each press of the
button. The garage door opener will respond
by clicking, blinking or activating.

Garage Door
Opener Brand
Type/Color of
SMART/LEARN
button
Year Times to
press
remote
button
Linear®Mega-Code 1997-
Current 1
Chamberlain®* Orange/Red 1997-
2003 2
Chamberlain®* Purple 2005-
Current 3
Chamberlain®* Green 1993-
1996 4
Genie®**
Overhead Door®Intellicode 2005- Current 5
Genie®
Overhead Door®Intellicode 1995- Current 6
Stanley®Secure Code 1998 7
Chamberlain®* Yellow 2011-
Current 8
Wayne Dalton®Rolling Code 1999 9
Xtreme
Garage®***
Guardian®*** Black 2016-
Current 10
Sommer*** Black 2013-
Current 11
Ryobi Rolling Code 2016-
Current 12
*Chamberlain, LiftMaster, Sears Craftsman, Do-It Master
Mechanic, Raynor, True Value and Sears Craftsman are
compatible with Chamberlain technology.
** Find Genie Intellicode II instructions at
support.chamberlaingroup.com.
*** Compatible with KLIK5U-BK2 and KLIK5U-SS only..
4. Press the program button on the remote
control to save.
5. Test by pressing the button you just
programmed. The opener activates.
To program the remote to Chamberlain accessories,
refer to the manual provided with the accessory.

BATTERY
To prevent possible SERIOUS INJURY or
DEATH:
•NEVER allow small children near batteries.
•If battery is swallowed, immediately notify
doctor.
To reduce risk of fire, explosion or chemical
burn:
•Replace ONLY with 3V CR2032 coin
batteries.
•DO NOT recharge, disassemble, heat above
212°F (100°C) or incinerate.
Dispose of batteries properly.
Replace ONLY with 3V CR2032 coin batteries.

NEED HELP?
Go to support.chamberlaingroup.com for more
information.
NOTICE: This device complies with part 15 of the
FCC rules and Innovation, Science and Economic
Development Canada license-exempt RSSs.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
Any changes or modification not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment.
All trade names used herein are trademarks of
respective manufacturers listed.

© 2023 The Chamberlain Group LLC.
All Rights Reserved
114-5462-000D

®
®
MODÈLE KLIK3C-BK2
MODÈLE KLIK3C-SS
MODÈLE KLIK5C-BK2
MODÈLE KLIK5C-SS
TÉLÉCOMMANDE UNIVERSELLE
Votre télécommande peut être programmée pour
faire fonctionner jusqu’à deux appareils, comme un
ouvre-porte de garage, un opérateur de portail ou un
opérateur commercial et est muni d’un bouton
SMART/LEARN (APPRENTISSAGE). Chaque bouton
de la télécommande fonctionne indépendamment
des autres et doit être programmé séparément. Les
images de ce manuel sont fournies à titre indicatif
uniquement et il est possible que votre produit soit
différent.
ARR T
Lisez attentivement les instructions
AVANT de commencer. Si vous
utilisez ce produit avec des ouvre-
portes résidentiels, il doit uniquement
être utilisé avec ceux qui ont été
fabriqués après le 1erjanvier1993 et utilisent des
capteurs photoélectriques situés près du bas du rail
de la porte.
IMPORTANT: La télécommande activera votre porte
ou votre portail pendant la programmation. Assurez-
vous que la porte est dégagée de TOUTES les
obstructions. Débutez avec la porte de garage
fermée. Assurez-vous que l’ouvre-porte de garage a
une lumière qui fonctionne, car c’est un indicateur
de programmation.
AVERTISSEMENT: Ce produit peut vous
exposer à des produits chimiques, dont le
plomb, qui sont reconnus par l’État de
Californie comme provoquant le cancer, des
malformations congénitales ou d’autres problèmes
de reproduction. Pour en savoir plus, visitez
www.P65Warnings.ca.gov.

CONNECTEZ-VOUS À L’APPLICATION
MYQ®
1. Fermez la porte du garage.
IMPORTANT: La télécommande active la porte
du garage pendant la programmation. Veillez à
ce que la porte soit dégagée de toutes les
obstructions.
2. Recherchez un logo Wi-Fi ou Powered by
myQ®pour déterminer si votre ouvre-porte de
garage est compatible à myQ logo to
determine if your garage door opener is
myQ®. Si ce n’est pas le cas, passez à la
programmation..
Ou
®
3. Pour commencer à surveiller les mouvements
de la porte de garage, scannez le code QR pour
télécharger l’application myQ.®.
4. Pour ajouter votre télécommande et votre
nom, suivez les instructions de l’application
dans l’ordre..
5. Après avoir terminé la configuration de
l’application, vous pouvez contrôler l’ouvre-
porte de garage et recevoir des avis chaque
fois que votre porte de garage s’ouvre et se
ferme.