Chamberlain 972MOM Moore-o-Matic User manual

Instructions are Described and
Illustrated Below
If you have a lighted push button that
looks like the lighted push button
illustrated follow the instructions below.
1. Remove the cover from the Lighted Door
Control.
2. Press and hold the button on the
hand-held remote that you wish to operate
your garage door.
. While holding the remote button, press
and hold the “A” button on the Lighted
Door Control.
4. Continue holding both buttons while you
press the “B” button on the Lighted Door
Control (all three buttons are held).
5. Release buttons when the motor unit
lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be
heard.
If you have a multi-function wall control
follow instructions below.
1. Press and hold the button on the
hand-held remote that you wish to
operate your garage door.
2. While holding the remote button, press
and hold the light button on the Multi-
Function Door Control.
. Continue holding both buttons while you
press the push bar on the Multi-Function
Door Control (all three buttons are held).
4. Release buttons when the motor unit
lights blink. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.
If neither of the two programming
instructions match your type and style of
opener follow instructions below.
Press and release the “learn” button on the motor unit. The learn
indicator light will glow steadily for 0 seconds. Within 0
seconds, press and hold the button on the hand-held remote.
Release the button when the motor unit light blinks. It has
learned the code. If light bulbs are not installed, two clicks
will be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first
erase all codes:
Press and hold the “learn” button on motor
unit until the learn indicator light goes out
(approximately 6 seconds). All previous
codes are now erased. Reprogram each remote or keyless entry
you wish to use.
Model 972MOM
Security✚2 Channel Remote Control
The 972MOM remote control can activate two separate
residential or commercial garage door openers and/or gate
openers. The instructions for programming garage door
openers are illustrated below. Please refer to the original
receiver programming for commercial and gate products.
Both push buttons are factory programmed to work with
Security✚receivers having an orange “learn” button. The rolling
code between these channels and the receiver changes with
each use, randomly accessing over 100 billion new codes.
As an added feature, the push button on the right is capable of
learning or being trained to duplicate or match another CGI
manufactured fixed code or billion-code remote. This feature is
normally used when several remotes are required to operate
one fixed code device such as a gate opener or commercial
dock door. In this case, the code transmitted to the receiver
remains constant or fixed, not using the Security✚ format.
NOTE: The push button on the left cannot be changed from
Security
✚ , only the right button is trainable.
Right Push Button
(Multi-use)
OWNER S MANUAL
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
ATTENTION
AVERTISSEMENT AVERTISSEMENT
AVERTISSEMENT
The Remote Control Batteries
The lithium batteries should produce power
for up to 5 years. To replace, pry open case
with visor clip or screwdriver, as shown.
Insert batteries positive side up (+).
Dispose of old batteries properly.
To prevent possible SERIOUS INJURY or DEATH:
NEVER allow small children near batteries.
If battery is swallowed, immediately notify doctor.
WARNING
CAUTION
WARNING
WARNING
ATTENTION
AVERTISSEMENT AVERTISSEMENT
AVERTISSEMENT
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
"A"
Button
"B"
Button
LOCK
LIGHT
LOCK
LIGHT

© 2002, The Chamberlain Group, Inc.
114A2717 All Rights Reserved Printed in Mexico
Resetting the Right Push Button Back to
Security✚as Follows:
Push and hold both buttons while observing
the small yellow indicator light. Hold both
buttons for ten seconds until the yellow
indicator light stops blinking. The remote has
defaulted to one of six randomly
preprogrammed Security✚settings.
When Several Remotes Operate
One Device:
To match the 972MOM to another CGI manufactured
remote’s code (Remote Control X):
1. Begin by having both the 972MOM and Remote
Control X available.
2. Press and hold both buttons on
the 972MOM until the yellow
indicator light, visible on the
bottom through a small hole,
begins to blink. It will blink for 0
seconds; during this time it is in
the learn or training mode, and
the buttons can be released.
. While it is in learn mode, hold
Remote Control X, another CGI
fixed or billion-code transmitter,
back to back with FCC labels
touching as illustrated.
4. Press and hold the Remote
Control push button as you
slowly slide the remotes across
each other until the 972MOM
indicator light blinks very rapidly,
indicating it has learned the
code. (If Remote Control X is
also a 972MOM, you must press
and hold its right push button.)
5. The right button is now sending
the same identical coded signal
as Remote Control X. This code
will remain inside the 972MOM
until replaced with another new
code by repeating steps 1-4
above, or by resetting
to Security✚.
FCC Label
Remote Control X
Yellow
Indicator
Light
Yellow
Indicator
Light