Channel Vision DS3-0212 User manual

500-275 rev A
www.chann e l v i s i o n . c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
[phone] [phone] [phone] fax
email: [email protected]
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs
during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from the
date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty
does not cover damages in shipment, failures caused by other products not supplied by Channel Vision
Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is
extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase
date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling [phone] toll free. A Return
Authorization number must be obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other rights (which vary from state to state).
If a problem with this product develops during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.
Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical
environment applications. Channel Vision customers using or selling Channel Vision products for use in
such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages
resulting from such improper use or sale.
1
Specifications:
Speaker Size (mm):
Speaker Impedance:
Speaker Power Peak (W):
Speaker Frequency Range:
Power Supply:
Power Consumption:
Cable Requirements:
Internal Relay Type:
Relay Specifications:
Camera Lens:
Resolution:
S/N Ratio:
Min Illumination:
Power Consumption:
Electronic Shutter:
Iris Control:
White Balance:
Video Output:
Operating Temp:
50
8 Ohms
0.2
500 Hz - 3.5 kHz
12VDC, 500mA
80mA (idle), 110mA (active)
8-conductor wire, 24AWG or larger
Note: wire carrying current to electric locks will
need to be much thicker. Consult the electric
lock documentation for its specific wiring
requirements.
Normally Open or Normally Closed
1Amp@12V
5.5mm
550 lines
More than 48 dB
0.2 LUX @ F2.0
12VDC, 65mA
1/60s - 1/100,000s
Automatic
Automatic
1 Vp-p @ 75 ohms
-10°C to 50°C (14°F to 122°F)
Color Camera: (DS3-6xxx, DS3-6xxxC, & DS3-6xxxP only)
Specifications subject to change without notice.
DS3
DS3
DS3
-XXXX
-XXXXC
-XXXXP
Telephone Entry Door Intercom
0
1
123
456
789
*0#

2
Channel Vision’s DS3-Series door stations can interface with
a variety of telephone entry control products to provide
communication with the front door. They are available in a
variety of configurations including options for a hidden
camera and compatibility with Panasonic’s popular KSU
phone systems. These door stations also feature an
integrated access control keypad which can be used to open
an entrance gate or an electric door lock. The DS3-Series
door stations install in a standard 3-gang junction box,
making it a simple and affordable addition to any home.
Dimensions:
7.25”
5.0”
0.38”
1.25”
Depth
Behind Plate
Plate
Depth
Only
Features:
h
h
h
h
h
Rust-proof faceplate
Discrete speaker and microphone
Hidden camera option available
Fits a 3-gang box
Available in many different finishes
123
456
789
*0#
11
Controlling Electric Locks
Keypad
Power
Suppy
Some installations may require a relay that exceeds the current capacity
of the DS-Keypad. For these situations an external relay can be used as
shown below. The DS-Keypad will provide a 12VDC trigger voltage to
activate the relay whenever the door opening function has been activated.
Green
Blue
Black
Red
–
+
Diode
Yellow
Simple
push button
Use an external relay to drive an alarm system. When the tamper switch
is depressed there will be no voltage driving the relay. If the tamper switch
is released, then there will be 12VDC between the Gray and Red wires
which will activate the relay.
Fail-Safe: Use this diagram for any lock that requires a Normally Closed
control contact, such as electromagnetic locks.
12VDC
External Relay
N.O.
N.C. Com.
#
0
*
9
8
7
6
5
4
123
Keypad
Power
Suppy
Gray
Black
Red
–
+
Diode
12VDC
External Relay
N.O.
N.C. Com.
#
0
*
9
8
7
6
5
4
123
Fail-Safe
Lock (N.C.)
Strike
Power
Supply
Keypad
Power
Suppy
Blue
Diode
Orange
Yellow
Black
Red
Simple
push button
–
–
+
+
#
0
*
9
8
7
6
5
4
123
Using An External Relay

10
Fail-Secure
Lock (N.O.)
Controlling Electric Locks
Strike
Power
Supply
Keypad
Power
Suppy
The DS-Keypad contains both Normally Open and Normally Closed relay
contacts allowing it be used for either “fail-safe”or “fail-secure”lock
mechanisms. Fail-secure locks remain locked when the power is off and
unlock when power is applied to the mechanism. Of course it is still
possible to manually open the lock from the inside of the building. Most
electric locks are fail-secure. Fail-safe locks require constant power to
remain locked. They are unlocked in the absence of power.
Blue
Diode
Green
Yellow
Black
Red
Simple
push button
–
–
+
+
Fail-Secure: Use this diagram for any lock that requires a Normally Open
control contact.
Note: the simple push button shown below is optional and can be omitted.
#
0
*
9
8
7
6
5
4
123
Fail-Secure
Lock (N.O.)
Strike
Power
Supply
Keypad
Power
Suppy
Diode
–
–
+
+
#
0
*
9
8
7
6
5
4
123
Strike
Active
Ring
Intercom
Active
12VAC
#
or
*
No CO
Strike
Time
3/5 rng
1
2
3
PowerIntercomUnlock
Door
ChimeCO Input Phones
TELEPHONE ENTRY CONTROLLER
CO Input Telephones
Model
P-0920 PRO
C
V
HANNEL
ISIONTM
From Telephone
Service Provider
Connect the Blue &
Green wires from the
keypad to the
“Unlock Door”
terminals. Triggering
the keypad will
cause the P-0920
to activate the
TE110DS and allow
the door to open.
House
Telephones
12VAC
500mA
Black
Red
Green
Blue
TE110DS
(Sold Separately)
Integrating the TE110DS
P-0920
33
Understanding the model number:
Understanding the compatibility options
(DS3-0212C shown for example only)
Part numbering: IU door plates
DS3-0212C Blank P-0920, P-0921, & TE110/C-0920 compatible
C P-0930 compatible
P Panasonic compatible (KX-TA624)
212 White
222 Polished Brass
232 Antique Brass
242 Chrome
252 Oil Rubbed Bronze
262 Antique Copper
272 Satin Silver
282 Black
302 Satin Nickel
0 No camera
6 Color camera (Note: camera option is not
available on IU-xxxxP8 models.)
There are three different types of systems that DS3 door stations can
be used with. The compatibility for these different types of systems is
indicated by the suffix of the model number which follows the 4-digit
numerical code.
If there is not a letter suffix on the model number, such as DS3-0212,
that door station is compatible with Channel Vision’s telephone entry
products including models P-0920, P-0921, C-0920, and TE110.
If the suffix is the letter “P”, such as DS3-0212P, then the door plate
is compatible with Panasonic’s phone systems which are designed to
use the Panasonic door phone model: KXT-30865.
If the suffix is the letter “C”, such as DS3-0212C, then the door plate
is compatible with Channel Vision’s Whole-House CAT5 Intercom
Hub, model P-0930.
Please double check to be sure that you have purchased the correct
model number for your application.

This door intercom product consists of two sub assemblies which must be
attached to each other before the final assembly can be installed. In this
guide the electronic sub assembly will be referred to as the “Companion
Board”and the mechanical assembly will be referred to as the “Door Plate.”
Review the following diagrams and assemble as shown.
Attaching the Companion Board
Companion Board Connection Details
To Button
To Speaker
Microphone
Connect Telephone Entry Controller here
(see following pages for details)
Remove the plastic cap that covers the microphone compartment on the
door plate. Place the microphone in the compartment and replace the plastic
cap over the microphone. Note that the plastic cap will form a friction fit over
the top of the microphone wires holding them snug against the outer
compartment wall until they exit at the base as shown. Remove the mounting
screws which are already attached to the bracket and use them to attach the
companion board. The companion board should mount on the front side of
the bracket so that the screws pass through the companion board before
threading into the bracket.
4
Place microphone here and
cover with cap.
Microphone cap
Companion board
9
Programming the Keypad
When programming the “#”key is used as the Confirmation or “Enter”key.
In most cases “*”is used to clear an entry or exit a process.
Change the 8 user passwords
Press:
System Reaction:
Press:
Press:
System Reaction:
* # [system password] #
One beep
3 [enter 1-8 (example:”1”for the first password, “2”for the second...)]
[enter the 4-digit password]
One beep (Password changed successfully)
Optional: [enter 1-8 to change another password] [enter 4-digit password]
Press:
System Reaction:
*
One beep (Process completed)
Set Door Strike Time Duration
Press:
System Reaction:
Press:
System Reaction:
* # [system password] #
One beep
4 [enter the 2-digit time duration in seconds (01-99)]
One beep (Time duration set successfully)
Opening the Door Lock with a System Password
Press:
System Reaction:
* # [system password] # 0 0
One beep, power light turns green and door is unlocked
Opening the Door Lock with a User Password
Press:
System Reaction:
[user password]
One beep, power light turns green and door is unlocked
Changing the System Password
Press:
System Reaction:
Press:
System Reaction:
Press:
Press:
System Reaction:
* # [system password] #
One beep
8 [enter new 4-digit system password] #
One beep
[re-enter new 4-digit system password for confirmation]
Note: If confirmation password didn’t match, you’ll hear repeated beeps,
and the system will exit the process. If no beeps are heard, then
continue.
#
Two Beeps (the new password has been saved)
Change Anti-Tamper Switch Setting: 0=ON 1=OFF
Press:
System Reaction:
Press:
System Reaction:
* # [system password] #
One beep
7 [enter the desired anti-tamper mode, 0=On, 1=Off]
One beep (Anti-Tamper mode has been set)
Setting Activation Mode
Set the activation mode before attempting using the user passwords.
* # [system password] #
One beep
5, 1
One beep (The mode has been set)
To set activation:
Press:
System Reaction:
Press:
System Reaction:

8
Using the Access Keypad
DS3-xxxxC
500ft.
max
The diagram below shows how to connect the DS3-xxxxC to Channel
Vision’s CAT5 Whole-House Intercom system. When the button is pressed
on the DS-xxxxC the ST-2000 Intercom Stations will generate a door chime.
Pressing Answer/End will open communication with the DS3-xxxxC. Model
DS3-6xxxC includes a color camera and DS3-0xxxC includes no camera.
Channel Vision Compatible
( -xxxx )
CAT5 Intercom
DS3 C
P-0930
PRO
C
V
HANNEL
IS I ONTM
Model
P-0930 Whole-House Intercom
Page Out
Page Trigger
IR
Emitters +15VDC
Power
Link
In
Link
Out
Hub
A
B
C
DRoom 1 Room2 Room 3 Room 4 Room 5 Room 6
ST-2000
Press here to
answer door
These terminals can be
used to connect a ST-C5IDS
Door Strike Relay Module Room 1
Room 2
Room 3
Room 4
Room 5
Room 6
Monitor
DND Answer/End
Page
Using CAT5 wire, connect the
P-0930 to the 110 connector
on the door station
Orange: Relay Norm. Closed
Power Light: Standby (Red)
Active (Green)
if power light
does not illuminate,
immediately disconnect
power supply and check
for correct polarity.
IMPORTANT:
Blue: Relay Common
Green: Relay Norm. Open
White: External Orange LED
Yellow: Door Push button
Gray: Additional Relay
Purple: Alarm Out (Additional Relay)
Black: Ground
Red: +12V
#
0
*
9
8
7
6
5
4
123
Tamper switch - If using
the tamper switch feature,
this must remain depressed
when the keypad is installed.
5
This door intercom product consists of two sub assemblies which must be
attached to each other before the final assembly can be installed. In this
guide the electronic sub assembly will be referred to as the “Companion
Board”and the mechanical assembly will be referred to as the “Door Plate.”
Review the following diagrams and assemble as shown.
Attaching the Companion Board
(DS3-XXXXC)
Companion Board Connection Details
To Speaker
Microphone
(attached to back side) Use D1 for Door1 chime sound
Use D2 for Door2 chime sound
Volume Adjustment
Position the companion board onto the three mounting tabs as shown below.
The microphone attached to the back side of the companion board should
line up with the microphone tube on the bracket. Bend the mounting tabs to
secure the companion board. Connect the speaker and button wires by
sliding the small connector over the exposed pins on the companion board
as shown.
To Button
Companion Board
Connect Button Here
Connect Speaker Here
Microphone
Tube
Align holes with
mounting tabs
Bend mounting
tabs over to
secure the
Companion Board
Connect Intercom Hub here
(see following pages for details)
Completed Sub-assembly

#
0
*
9
8
7
6
5
4
123
6
The DS3-6xxx, DS3-6xxxC, & DS3-6xxxP come with a mini color camera that
can be attached to the integrated mount that allows the camera to see
through the opening in the plate. The illustrations bellow show how to mount
the camera.
Attaching & Installing the Camera
Mini Camera
Mounting
Hole
Cone
Lens
Connect Intercom Hub here
(see following pages for details)
Break away the section of perforated metal screen that
covers the camera opening by pushing a screwdriver
through the slot on the front of the door plate. Press
near the top or bottom of the section and the tabs that
hold it in place will break free. Attach the camera to the
mount so that the cone of the camera points through
the opening. Adjust the camera to the desired position
and secure it in place by tightening the screw on the
mount.
Remove this
section of screen
material
Front View
Rear View
Attach camera to mount
using the screw provided
Attach pigtail
to rear of
camera
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
Video
Connector
BNC
2-Conductor Power
Supply Extension
(not included)
Installation:
hIf necessary, attach the camera’s video output to a coax extension
that is long enough to reach your monitor or video distribution
equipment.
If necessary, cut the connector off of the end of the power supply and
splice in an extension using crimp-on connectors.
h
7
The DS3 DS3 both interface with the Channel Vision
TE110 C-092 to provide
audio and video communication with the front door. Using a 2-conductor
wire, connect the Telephone Entry Controller to the empty screw terminal
block on the door station (see diagram).
-0xxx and -6xxx ’s
telephone entry controllers: , 0, P-0920 and P-0921
Channel Vision Compatible (DS3-xxxx)
Panasonic (DS3-xxxxP)Compatible
Strike
Active
Ring
Intercom
Active
12VAC
#
or
*
No CO
Strike
Time
3/5 rng
1
2
3
PowerIntercomUnlock
Door
ChimeCO Input Phones
TELEPHONE ENTRY CONTROLLER
CO Input Telephones
Model
P-0920 PRO
C
V
HANNEL
ISIONTM
Connect to the
terminals marked
“TO SYS”
From Telephone
Service Provider
House
Telephones
12VAC
500mA
Using a 2-conductor wire, connect the door
phone output of your Panasonic KSU to the
empty screw terminal block on the door station
Channel Vision's Panasonic models are a compatible replacement for the
Panasonic KXT30865. The an attractive alternative to the standard
plastic door station sold by Panasonic.
y are
This product interfaces with
Panasonic’s KSU phone systems to provide communication with the front
door.
Connect to the
terminals marked
“TO SYS”
From Telephone
Service Provider
System Phones
Panasonic
KSU