Channel Vision 6330 User manual

500-214 Rev D1
CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs
during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from
the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This
warranty does not cover damages in shipment, failures caused by other products not supplied by Channel
Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty
is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling [phone] toll free. A Return
Authorization number must be obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other rights (which vary from state to state).
If a problem with this product develops during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.
* :
Image Sensor:
Picture Elements:
Resolution:
S/N Ratio:
Min Illumination:
Electronic Shutter:
Iris Control:
Gamma Characteristic:
Waterproof Rating:
Dimensions:
Operating Temp:
Specifications
1/3” Hi-Res CCD
NTSC: 768x494
540 lines
More than 48 dB
0.02 LUX @ F1.2 (Day), 0 Lux @ F2.0 (Night)
1/60s - 1/100,000s
Automatic
0.45
IP68
2.75” x 4.75” (70mm x 120mm), camera body only
-10°C to 50°C (14°F to 122°F)
*Specifications subject to change without notice.
White Balance:
Focal Length & App. Ratio:
Angle Field of View:
Sync. System:
Power Requirements:
Power Consumption:
Infrared Illumination:
LED Wavelength:
Illumination Distance:
Video Output:
Automatic
6mm, F2.0
Horizontal: 43.6° x Vertical: 33.4°
Internal
12VDC
85mA (IR off), 650mA (IR on)
36 IR LEDs
850nm
99 feet (30 meters)
1 Vp-p @ 75 ohms
6330
Hi-Resolution IR Bullet Camera
0
1

2
The is a high-resolution Infra Red illuminated bullet
camera. Its waterproof design and LED illumination make it
ideal for CCTV installations where there is no ambient light
and no shelter for the camera. Typical applications include
entry gates, driveways, patios, and backyards.
6330
6330 IR Bullet Camera Includes
Swivel Mount Extension
Base
Camera
Power Supply
Screws Anchors
Features:
High quality 1/3” Hi-Res CCD sensor
540 TV lines of resolution
Viewing distance of 99 feet (30 meters) in total darkness
Built-in 36 LED illuminator
Built-in light sensor turns off LEDs during the day
Waterproof and suitable for outdoor use
Easy to install
h
h
h
h
h
h
h
Warnings:
h
h
h
h
Do not look directly into the illuminated camera when in use.
Do not touch the body of the unit when in use. It can reach
temperatures as high as 150ºF.
Do not point the LED illuminated camera directly at paper or
flammable materials.
Avoid touching the lens with fingers. Clean off any finger
prints with cleaning alcohol and cotton swabs.
3
Model 6330
1. Mount base
2. Connect camera and swivel mount
3. Connect wiring
Important Note:
No more than one 6330 should be used with
Channel Vision’s P-6014 camera sequencer.
Installation:
Drill a hole for wiring to exit the wall or ceiling.
Attach the base of the swivel mount using the screws
provided. If mounting to a j-box use the 5032 mounting
plate (sold separately).
If necessary, attach the camera’s video output to a coax
extension that is long enough to reach your monitor or
video distribution equipment.
If necessary, cut the connector off of the end of the power
supply and splice in an extension using crimp-on
connectors.
Screw the swivel mount into the base and attach the
camera (see diagram).
Move the camera body to adjust the view.
h
h
h
h
h
h
2-Conductor power
supply extension
(not included)
Crimp-on splice
connectors
(not included)
To Monitor
or
Video distribution
Power supply
(included)
Coax extension
(not included)
BNC connector