Char-Griller Outlaw #2137 User manual

OM2137 B.2 ™ & © Char-Griller / A&J Mfg.
Owners Manual
Charcoal Grill
Model# 2137
Outlaw
Keep your receipt with this manual for Warranty.
600039

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 2
STOP! CALL FIRST! DO NOT RETURN PRODUCT TO STORE.
CALL [phone] This product has been built to the highest quality standards.
Call us should you have any questions not addressed in these instructions, or for
service information.
Have your grills serial number (located on the back of the grill body or on the leg)
when calling.
13
22
3
1
2
17
7 19
21
20
6
12
11
8
12
16
9
10
5
No Returns on
Used Grills
14
18
23
15
4

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 3
PARTS LIST AND TOOLS REQUIRED
(Tools Not Included)
Pliers and 7/16" nut driver
ITEM QTY PART NAME PART NUMBER
1 1 HOOD 20-0082
2 1 GRILL BODY 20-0083
3 1 HEAT GAGE 55-0010
4 1 HOOD HANDLE 55-0014
5 1 WARMING RACK 30-0058
6 1 BOTTOM SHELF 20-0130
7 2 LONG LEG 10-0120
8 2 SHORT LEG 10-0121
9 1 ASH PAN 20-0135
10 4 COOKING GRATE 10-0049
11 2 WHEEL 55-0003
12 2 LEG BRACE 10-0051
13 1 AXLE 10-0324
14 2 ASH PAN HANGERS 20-0024
15 3 UTENSIL HOOK 50-0003
16 1 DAMPER CIRCLE 10-0036
17 1 SIDE SHELF 30-0016
18 2 HUB CAP 55-0007
19 2 FRONT SHELF SLAT 10-0115
20 2 FRONT SHELF SUPPORTS 10-0053
21 2 FRONT SHELF BRACKETS 10-0052
22 1 STACK 30-0088
23 1 GRATE LIFTER 10-0045
2 ¼”
35 pcs.

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 4
Page Intentionally Left Blank For Notes

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 5
ASSEMBLY INSTRUCTIONS
Read all safety warnings and instructions carefully before
assembling and operating your grill.
IMPORTANT HINT: DO NOT TIGHTEN ANY NUTS AND BOLTS UNTIL
GRILL IS FULLY ASSEMBLED.
(Estimated Assembly Time: 45minutes)
1. Assembly requires 2 people. Get another person to Help. For easiest assembly
use a HAMMER, PLIERS and a 7/16" NUT DRIVER. NOTE: Do Not tighten any
bolts unless instructed to do so. Tightening too soon may prohibit parts from Fit-
ting together. All Hex Nuts should be on the Inside of the grill unless stated oth-
erwise. Unpack all contents in a well-cleared and padded area.
2. Insert one LONG LEG into one SHORT LEG. See below. Repeat this step for the
other LONG and SHORT LEG.
3. Attach the LONG LEGS and SHORT LEGS to the base with four (4) lock washers
and 2 1/4” Bolts and four (4) hex nuts as shown below.
Short Leg Long Leg

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 6
4. Attach LEG BRACE to the outside of the LONG LEG using 2 1/4” Hex Bolts and
Nuts as shown but only finger tight.
5. Attach the other end of the LEG BRACES to the corresponding legs using 2 1/4"
Hex Bolts and Nuts but only finger tight. See below.
6. Insert the AXLE through the SHORT LEGS and through the BASE. Slide WHEELS
onto AXLE, install washer and cotter pin then hammer HUB CAPS onto each end of
the AXLE to secure WHEELS.

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 7
7. Stand the CART/LEG ASSEMBLY upright. Attach the bottom half of the BODY to
the CART/LEG ASSEMBLY (make sure damper is on same side as wheels) with
four 2 1/4" Hex Bolts. There are two holes in the front and two in the back of the
grill BODY. See below.
8. Attach two (2) 8" FRONT SHELF BRACKETS to the front edge of BOTTOM HALF
of grill body using two (2) 3/4" Hex Bolts and Nuts (with the nuts on the inside
of the grill). Attach the long WOOD SLATS to the FRONT SHELF BRACKETS and
at the same time attach the FRONT SHELF SUPPORT BRACES to the underside
of the outer Holes of the FRONT SHELF BRACKETS with four (4) 1" Carriage
Bolts and Nuts. Attach the other end of the Support Braces to the Grill Body.
See below.
9. Insert SMOKESTACK from INSIDE the HOOD up through the hole. Attach with two
(2) 3/4" hex bolts with the nuts on the inside. See below. Note: It is not neces-
sary to remove the Stack Damper.
Damper
Hex Bolt
Hex Nut
Smokestack
( Insert from inside)
Carriage Bolt
Front Shelf
Bracket
Front Shelf Support Brace
Attach to Grill Body
Bottom Half of
Grill Body
Hex Nut

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 8
10. Insert HEAT GAUGE through hole in hood (from outside) and push the SPLIT
RING over tabs on the side of HEAT GAUGE from inside the hood.
11. Attach WOOD HOOD HANDLE to the center of the HOOD with two (2) 3/4" hex
bolts, lock washers, and hex nuts. See below.
12. Set the HOOD, in the CLOSED POSITION, on top of the bottom Half of the grill
body. Line up the Hinge holes and insert the Hinge Pins. This may require lifting
up on the back of the Hood. Then, carefully open the hood, making sure to not
let the Hinge Pins fall out, and insert the Hair Cotter Pins into the Hinge Pins.
See below.
Hood
Hinge
Hair Cotter Pin
Hinge Pin

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 9
13. Attach the DAMPER CIRCLE from the inside of bottom half of grill body with a
3/4" Bolt. The bolt goes thru a Flat Washer, thru the Damper Circle, thru the
Grill Body, thru another Flat Washer, thru a Lock Washer, and finally attached to
a Hex Nut. The small tab on the Damper Circle should protrude outward. Fig. J.
14. Attach SIDE SHELF to the four (4) holes on left side of grill with 1/2" hex bolts
and nuts. See below.
Hex Nuts
Hex Bolts
Side Shelf
Inside of
Charcoal
Grill Body

OM2137 B.2 ™ & © Char-Griller / A&J Mfg. 10
15. ATTACHING WARMING RACKS PIVOT BOLTS: On each END of the HOOD just
back of center, insert one (1) 2" HEX BOLT (total 2) (from outside in) in holes (A)
with HEX NUTS on inside of HOOD. See Below.
On each END of the LOWER GRILL BODY 4" from the back corner, insert one (1)
3/4" HEX BOLT (total 2) (from outside in) in holes (B) with HEX NUTS on inside
of GRILL BODY. See below.
Do not install WARMING RACK until after tightening all four WARMING RACK
PIVOT BOLTS.
ATTACH THE WARMING RACK’S (4) WIRE LOOP HOLES, located on the WARM-
ING RACK’S SIDES and WIRE LEGS, over the four (4) PIVOT BOLTS in the HOOD
and GRILL BODY. Attach left side first. Hint: You may flex the WIRE LEG out-
wards for a tighter fit and to center. See below.
16. Tighten ALL nuts and bolts.
17. Place FIRE GRATE, with ADJUSTABLE HANGERS attached, into BOTTOM HALF of
grill body. See Below. Install the COOKING GRATES.
CONGRATULATIONS, ASSEMBLY COMPLETE!
Fire Grate
2” Bolt
3/4” Bolt
A
B A
B
Inside of
Hood Hex Nut