Char-Griller Wrangler 2823 User manual

OM2823 A.1 ™ & © Char-Griller / A&J Mfg.
OWNER’S MANUAL
Wrangler™ Charcoal Grill
Model # 2823 / D2823 / E2823
Keep your receipt with this manual for Warranty.
CUSTOMER SERVICE
1-912-638-4724
[e-mail]
Contents of this manual are Trademarked and Copyrighted by Char-Griller | A&J Manufac-
turing. Using the information contained in this manual without consent of Char-Griller and/
or A&J Manufacturing is strictly prohibited.

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 2
 Grill is for outdoor use only.
 Use caution when assembling and operating your grill to avoid
scrapes or cuts from sharp edges.
 Do not use gasoline, kerosene or alcohol for lighting charcoal. Use
of any of these or similar products could cause an explosion
possibly leading to severe bodily injury.
 Keep children & pets away from grill. Supervision is necessary and
do not leave grill unattended when in use. Use caution when
moving grill to prevent strains. Keep grill at least 15 feet from any
combustible material (decks, buildings, fences, trees, bushes, etc).
 When adding charcoal and/or wood, use extreme caution.
 Never move grill when it is in use or when it contains hot coals or
ashes.
 Do not place grill near flammable liquids, gases or where
flammable vapors may be present.
 Use caution since flames can flare-up when fresh air suddenly
comes in contact with fire. When opening the lid, keep hands, face
and body safe from hot steam and flame flare-ups.
 Warning: To avoid injuries, gloves or other protective articles should
be used when touching the ash pan hangers.
IMPORTANT SAFETY WARNINGS
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING AND OPERATING YOUR GRILL

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 3
P.O. Box 30864
Sea Island, GA 31561
912-638-4724
www.CharGriller.com
Warranty Information —Charcoal Grill
Char-Griller® will repair or replace any defective part of its grillers/
smokers for a period of up to one year from the date of purchase. Char-
Griller® will also repair or replace the body (bottom half) of its grillers/
smokers if the metal is rusted through or burned through for a period up
to five years. Char-Griller will repair or replace any defective part of its
side fire boxes for a period up to one year from the date of purchase.
Proof of purchase, proof of purchase date, photo and prepaid return of
the item in question may be required. Misuse, abuse, or commercial use
nullifies all warranties. Paint/finish is not warranted. Products are not
warranted against rust.
The warranty is for replacement of defective parts only. Manufacture will
not be responsible for damage resulting from accident, alteration, mis-
use, abuse, hostile environments, improper installation, installation not in
accordance with local codes of service of unit.
This limited warranty does not cover any scratches, dents , corrosion or
discoloring by heat, abrasive and chemical cleaners nor any components
used in the installation of the appliance.
Save your receipt for all warranty claims.
WARNING: This product and com-
bustion by-products produced when
using this product contain chemi-
cals known to the State of Califor-
nia to cause cancer, birth defects,
or other reproductive harm.

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 4
STOP! CALL FIRST! DO NOT RETURN PRODUCT TO STORE.
CALL [phone] This product has been built to the highest quality standards.
Call us should you have any questions not addressed in these instructions, or for
service information.
Have your product’s serial number (located on the back of the grill body or on the
leg) when calling.
No Returns on
Used Grills

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 5
Item No. Description QTY/
Grill
1 Top Half of Grill 1
2 Cast Iron Grate 3
3 Warming Rack 1
4 Fire Grate Hanger 2
5 Ashpan 1
6 Grate Lifter 1
7 Bottom Half of Grill 1
8 Filler Plate 1
9 Damper Circle 1
10 Grease Cup Holder, Large 1
11 Leg Cross Bar 2
12 Leg Brace 2
13 Long Leg 2
14 Leg Cap 2
15 Bottom Wire Shelf 1
16 Short Leg 2
17 8" Plastic Wheel 2
18 Hub Cap 2
19 Axle Rod 1
20 Front Shelf - Right Support Bracket 1
21 Front Shelf—Left Support Bracket 1
22 Folding Front Shelf Metal Slat 2
23 Cup Hook 3
24 Metal Side Shelf 1
25 Hood Handle and Wingnuts 1
26 Bezel Handle 2
27 Char-Griller Logo Plate 1
28 Thermometer Bezel 1
29 Thermometer with Wingnuts 1
30 Smokestack Assembly 1
31 Smokestack Damper 1
32 Compression Spring, 10.6mm x 15mm 1
33 Akorn Nut, 5/16-18 1

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 6
(Tools Not Included)
Pliers and 7/16" nut driver
¼-20 x 2” BOLT……….....2 PCS ¼-20 HEX NUT……………......29 PCS
¼-20 x 1 3/4 ” BOLT….12 PCS ¼” LOCK WASHER………….....3 PCS
¼-20 x 3/4” BOLT…..... .3 PCS HAIR COTTER PIN (small).…...2 PCS
¼-20 x ½” BOLT…........ 10 PCS HINGE PINS…………................2 PCS
¼” FLAT WASHER…….....2 PCS HUB CAP…………......................2 PCS
2/5” FLAT WASHER….....2 PCS HAIR COTTER PIN (large).…...2 PCS
UTENSIL HOOKS.............3 PCS SHOULDER BOLT…................4 PCS
Hardware Pack

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 7
ASSEMBLY INSTRUCTIONS
Read all safety warnings and instructions carefully before
assembling and operating your grill.
IMPORTANT NOTE: DO NOT TIGHTEN ANY NUTS AND BOLTS UNTIL
GRILL IS FULLY ASSEMBLED.
Step 1: Assemble Long Legs, Short Legs, and Leg Braces as show below then secure the Leg
Braces to one set of Long Leg and Short Leg with 4 Hex Bolts and four 4 Hex Nuts.
Step 2: Install Bottom Wire Shelf by placing the four corner hooks inside the hole on each leg
then rotate the leg assemblies up and secure the Leg Braces to the other side of the Long Leg
and Short Leg set.
Leg Braces
1 3/4”
Hex Bolts
Long
Legs
Short Legs
Hex Bolts
Bottom Wire Shelf
Hex Nuts
1 3/4”
Hex Bolts

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 8
Step 3: Lay the cart assembly down with the Long Legs on the floor then install the Wheels and
Wheel Axle. On one end of the Axle insert the Cotter Pin into the hole on the Axle and snap in
the Hub Cap. Slide one Flat Washer and one Wheel onto the Axle then slide the Axle through
the holes on the Short Legs and Bottom Shelf. Complete the assembly by sliding the other
Wheel and Flat Washer onto Axle then insert the Cotter Pin and snap on the Hub Cap.
Step 4: Attach the Grill Body to the previous assembly cart using 4 Hex Bolts and 4 Hex Nuts.
The Bolts must go through the leg, Grill Body then tighten with the Hex Nuts inside the Grill
body.
Wheel Axle
Wheels
Cotter Pin (large)
Hub Cap
Hub Cap
Hex Nuts
1 3/4”
Hex Bolts
1 3/4” Hex Bolts
Cotter Pin
Flat Washer
(2/5”)
Flat Washer (2/5”)

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 9
Step 5: Attach Damper Circle to the side of the Grill Body with one Hex Bolts, two Flat Washers,
one Lock Washer, and one Hex Nut.
Flat Washers (1/4”)
Damper Circle
3/4” Hex Bolt
Lock Washer
Hex Nut
Step 6: Attach the Grill Hood to the Grill Body using the two Hinge Pins and two Cotter Pins
provided.
Hinge Pin
Hinge Pin
Grill Hood
Grill Body
Cotter Pins (small)

OM2823 A.1 ™ & © Char-Griller / A&J Mfg. 10
Step 7: Insert the Thermometer through the Thermometer Bezel then through the hole in Grill
Hood (from outside) then secure with a Wing Nut. Insert the Hood Handle through the Handle
Bezel and Grill Hood (from outside) then through Lock Washers then secure with Handle Wing
Nuts, see below.
Thermometer
Hood Handle
Thermometer
Wing Nut
Grill Hood
Step 8: Insert Smokestack Assembly through the hole on the Grill Hood from the inside of the
Grill Hood then secure it with two Hex Bolts and two Hex Nuts.
Handle Bezel
1/2” Hex Bolts
Smokestack
Hex Nuts
Grill Hood
Thermometer
Bezel
Handle Wing Nuts
Lock Washers