Charnwood Bay BX Product guide

Operating & Installation Instructions
®
charnwood
BAY BX

Ref. JT v1 07.16
C O N T E N T S
O P E R AT I N G I N S T R U C T I O N S
Fuel................................5
Controlling The Fire ...................5
Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Ash Clearance . . . . . . . . . . . . . . . . . . . . . . . 7
Reduced Burning . . . . . . . . . . . . . . . . . . . . . 7
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 7
Throat Plate & Flueway Clearing. . . . . . . . . 7-8
Chimney Sweeping . . . . . . . . . . . . . . . . . . . . 8
Trouble Shooting . . . . . . . . . . . . . . . . . . . . 8-9
CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . 9
If you need further help...............9
INSTALLATION INSTRUCTIONS
Unpacking The Stove . . . . . . . . . . . . . . . . . 10
Health & Safety Precautions . . . . . . . . . . . . 10
CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specification . . . . . . . . . . . . . . . . . . . . . . . . 10
Chimney . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Hearth & Fire Surround . . . . . . . . . . . . . . . 11
Connection to Flues . . . . . . . . . . . . . . . . . . 11
Soot Doors . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pre Lighting Check . . . . . . . . . . . . . . . . . . . 11
Commissioning . . . . . . . . . . . . . . . . . . . . . . 12
Clean Air Act Information. . . . . . . . . . . . . . 12
Certification . . . . . . . . . . . . . . . . . . . . . . . . 13
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 14
Bay BX Parts List . . . . . . . . . . . . . . . . . . . . 15

Add kindling and paper or
firelighters. Set the air control
to boost and close door
Once kindling is alight, add
smaller logs. Keep air control
set to boost and close door
Add larger logs once fire is
established. The Air control can
be reduced to medium output
LIGHTING AND CONTROLLING THE FIRE
®
OPERATING INSTRUCTIONS
®
QUICK GUIDE Your Charnwood Bay BX at a glance
Throat plate
Improves efficiency of stove by
slowing down flue gases
a
bDoor
Keep closed when stove is in use
cDoor handle
Pull to open
Fuel retainer
Ensure fuel does not protrude
beyond retainer
d
c
d
MAINTENANCE AND CLEANING
Suitable fuel for your
Charnwood:
This stove is designed to
burn only wood.
Unsuitable fuels:
Petroleum coke
Liquid fuel
Household waste
Coal singles
Small nuts or coal dust
Wet or unseasoned wood
p5
Optional Stand
Three options available:
Centre Stand, Store Stand
& Bench Stand
e
a
b
e
Fig. 1 Air control
1
2
34
1. Slumber
2. Medium output
3. High output
4. Boost
Air Control
p6
Glass
Wipe with damp, lint free cloth.
removed with a proprietary stove glass cleaner or ceramic hob cleaner.
Any stubborn deposits on the glass may be
Throat plate
Take down once a month and clean. Sweep sooty deposits into fire.
Chimney
Have chimney swept twice a year. Chimney can be swept through stove.
Servicing
Stove should be serviced by a professional at least once a year.

Take care not to touch the doors as they will be hot when the fire is
burning. Pull the door handle up to open, and push down to close.
The stove should be run with the door shut.
The rate of burning and hence the output is controlled by the air
control (see Fig. 2).
Open the air control fully when lighting or when rapid burning is
required. It should not be left fully open for long periods as this can
cause over-firing or excessive smoke production. For high output
move the air control to the ‘High Output’ position’ or for low
burning to the fully closed position.
CONTROLLING THE FIRE
When the fire is burning normally the air control gives enough
airwash to keep the glass clean. However, it will not always be
possible to keep the glass clean with the air control fully closed.
Congratulations on becoming the owner of a Charnwood Bay BX
Stove It is very important that you read and understand these
instructions before using the stove.
DOOR OPERATION
The door handle has been carefully designed so that in normal use it
may be operated using bare hands. However, if you need to open the
doors when the fire is running at maximum, then the use of the glove
provided may be required
.
FUEL
Before lighting the stove check with the installer that the work and
checks described in the Installation Instructions have been carried out
correctly and that the chimney has been swept, is sound and free
from any obstructions. The stove is not suitable for use in a shared
flue system.
Remember that the stove will be hot and that it is made from hard
materials – ensure that you have good balance before operating the
fire. Always use the provided operating tool and gloves.
Do not use an aerosol spray on or near the stove when it is alight.
There is a risk of explosion or flash ignition of the spray.
When using the stove in situations where children, aged and/or
infirm persons are present a fireguard must be used to prevent
accidental contact with the stove. The fireguard should be
manufactured in accordance with BS 8423:2002.
The stove is suitable for intermittent operation.
Only dry well seasoned wood should be burnt on this appliance as
burning wet unseasoned wood will give rise to heavy tar deposits in
the stove, on the glass and within the chimney. For the same reason
hard woods (such as Ash, Beech and Oak) are better than soft woods
(such as Pine and Spruce). Burning wet unseasoned wood will also
result in considerably reduced outputs. The wood should be cut and
split and then left to season in a well ventilated dry place for at least
one year but preferably two years before use. Approximate suitable
log sizes are:
480mm long and 75mm diameter
PETROLEUM COKE IS NOT SUITABLE FOR USE ON
THIS APPLIANCE. ITS USE WILL INVALIDATE THE
GUARANTEE.
This stove is not designed to burn household waste.
®
OPERATING INSTRUCTIONS
5
Fig. 1 Stove controls
Air control Fuel retainer Door handle
1
2
34
Air control handle
Fig. 2 Air control
1. Slumber
2. Medium Output
3. High Output
4. Boost

LIGHTING
On initial lighting, the stove may smoke and give off an odour as the
silicon paint with which the firebox is painted reacts to the heat. This
is normal and will cease after a short time, but meanwhile the room
should be kept well ventilated. At first only light a small fire and burn
it slowly for two hours to allow any residual moisture in the chimney
to evaporate.
Light the stove using dry kindling wood and paper or fire lighters. It is
recommended that you use approximately 1kg to 1.2kg of kindling.
Put the paper, or fire lighters, and kindling in the firebox and cover
with a few small dry logs. Open the air control fully (see Fig. 2). Light
the paper or fire lighters. The door may be left cracked open for a
few minutes to assist the combustion and heat up the firebox more
quickly.
When the kindling wood is well alight add a few more small logs and
close the door, but leave the air control fully open. When the flames
are established around the smaller logs, load the stove with larger
logs to the required fuel load. Logs should be no more than 75mm in
diameter and 480mm long. Close the door. Maintain the air control
at maximum at this stage.
Once long flames appear over the fire, reduce the air control to the
‘high output’ setting. Once the fire is well established - with each log
alight at the top - the air setting can be reduced again, depending on
the type of fire required. If at any stage the flames start to go out or
the glass begins to discolour, a higher setting is required. To achieve
this, open the air control to re-establish a consistent burn.
Once the fire is up to temperature the airwash system will begin to
work, so allow the fire to become hot before adjusting the air control
to the required setting. During the lighting period, do not leave the
stove unattended. Do not leave the door open except as directed
above to avoid excessive smoke.
When relighting the stove, leave the ash on the base unless it is
becoming too deep, in which case some of it may be removed.
Keep the firebox well filled but do not allow fuel to spill over the top
of the fuel retainer.
Logs should be evenly distributed, filling the firebed to give the most
pleasing flame pattern. The air control must be fully opened after
REFUELLING
6
®
OPERATING INSTRUCTIONS
Fig. 3 Initial firing
Fig. 4 Building up the fire
Fig. 5 Adding larger logs
Fig. 6 Fire well underway

refuelling until the flames are established above the fire. It is best to
refuel on to a hot bed of embers. If at this point the fire starts to die,
the door must be cracked open until the fire is revived. If the fire has
started to die down before refuelling, then more kindling wood must
be added, the air control opened fully and the door cracked open to
re-establish the firebed before adding larger logs (see suitable log
sizes in Fuel section). This will avoid excessive smoke emission.
Care should be taken, especially when burning wood, that fuel does
not project over the fuel retainer or damage to the glass may be
caused when the door is closed. It can also cause the glass to blacken
up. Maximum filling height is such that logs cannot fall from the fire
when the door is opened.
In smoke controlled areas do not fill the stove above the level of the
air holes in the back bricks, as overloading can cause excess smoke.
Do not operate with the door left open except as directed by the
instructions as this can cause excessive smoke.
For reduced burning the fire door must be closed.
When burning wood in areas that are not smoke controlled, load
some large logs on the fire and allow to burn for half an hour before
closing the air control (this will help to reduce tar deposits in the
chimney). Some experimentation may be necessary to find the setting
most suitable for the type of fuel being used and the draw on the
chimney.
Cleaning
ASH CLEARANCE
For optimum wood burning, it is important to leave a layer of ash,
around 1cm thick, on the base of the stove. If the ash is becoming too
deep, clear the top layer of ash cleared using the scoop provided.
The stove is finished with a high temperature paint which will
withstand the temperatures encountered in normal use. This may be
cleaned with a damp lint-free cloth when the stove is cold. Should re-
REDUCED BURNING
MAINTENANCE
painting become necessary, high temperature paints are available
from your supplier or from stove shops.
Most deposits on the glass may be burnt off simply by running the fire
at a fast rate for a few minutes. If it becomes necessary to clean the
glass then open the door and allow it to cool. Clean the glass using a
damp cloth and then wiping over with a dry cloth. Any stubborn
deposits on the glass may be removed with a proprietary stove glass
cleaner or ceramic hob cleaner. Do not use abrasive cleaners or pads
as these can scratch the surface which will weaken the glass and cause
premature failure
After long periods
where the fire has been out of use, the chimney and appliance
flueways should be cleaned before lighting.
It is important that the throat plate and all the stove flueways are kept
clean in order to prevent potentially dangerous fume emission. Check
by looking up into the firebox for signs of soot or fly-ash on the
throat plate and sides of the firebox. If there are signs of a build up of
soot or fly-ash then cleaning is necessary. Cleaning should occur at
Cleaning the Glass
When Not in Use
If the fire is going to be out of use for a long period (for instance in
the summer) then to prevent condensation, and hence corrosion, the
air control should be left fully open and the fire door left ajar. It Is
also advisable to sweep the chimney and clean out the fire. Spraying
the inside of the door and firebox with a light oil, such as WD40, will
also help to keep all internal parts working well.
Door Seals
For the fire to operate correctly it is important that the door seals
are in good condition. Check that they do not become worn or
frayed and replace them when necessary.
Servicing
It is recommended that the fire is serviced once a year to keep it in
first class working order. After cleaning out the firebox thoroughly,
check that all internal parts are in good working order, replacing any
parts that are beginning to show signs of wear. Check that the door
seals are in good condition and that the door seals correctly. A
servicing guide is available on request. Repairs or modifications may
only be carried out by the Manufacturer or their approved agents.
Use only genuine Charnwood replacement parts.
THROAT PLATE AND
FLUEWAY CLEANING
7
®
OPERATING INSTRUCTIONS
Fig. 7 Ash Scoop

CHIMNEY SWEEPING
TROUBLE SHOOTING
Where the chimney previously served an open fire, it is possible that
the higher flue gas temperature from a stove may loosen soot
deposits with the consequent risk of flue blockage. It is therefore
recommended that the chimney be swept a second time within a
month of regular use after installation.
The chimney should be swept at least twice a year. Where the top
outlet is used it will generally be possible to sweep the chimney
through the appliance.
First remove the fuel retainer, the throat plate and upper throat plate.
Then sweep the chimney ensuring that soot is removed from all
horizontal surfaces after sweeping.
In situations where it is not possible to sweep through the appliance
the installer will have provided alternative means, such as a soot door.
After sweeping the chimney the appliance flue outlet and the flue
pipe connecting the stove to the chimney must be cleaned with a flue
brush.
After clearing any soot from within the stove, replace the throat plate
(see Fig. 8) and the fuel retainer.
Fire Will Not Burn
Check that:
a) the air inlet is not obstructed in any way,
b) chimneys and flueways are clear,
c) a suitable fuel is being used,
d) there is an adequate air supply into the room,
e) an extractor fan is not fitted in the same room as the stove.
f) there is sufficient draw in the chimney. Once the chimney is warm a
draught reading of at least 1.25 mm (0.05 in.) water gauge (12Pa)
should be obtained.
Blackening of Door Glass
Differences in chimney draughts mean that the best settings of the air
controls will vary for different installations. A certain amount of
experimentation may be required, however the following points
should be noted and with a little care should enable the glass to be
kept clean in most situations:
Different types of sweep’s brushes are available to suit different
flueways. For prefabricated insulated chimneys the manufacturers
instructions with regard to sweeping should be consulted.
least once a month and more frequently if required. Let the fire out
and ensure it is cold before carrying out these operations. If
necessary, wear your Charnwood gloves to prevent irritation from
soot deposits.
The throat plate consists of two firebrick panels which rest on the
central bracket and the two side bricks. To lower, push the brick up
towards the topmost corner of the stove, and lower down diagonally
(see Fig. 8). Any sooty deposits should then be swept from the plate
and into the fire.
Return the throat plates to their correct position by reversing the
above method, ensuring they slot onto the bracket and rest securely
on the side panels.
8
®
OPERATING INSTRUCTIONS
Throat plate Side brick
Side View
Lowering the throat plate
Fig. 8 Throat plate position and lowering

a) Wet or unseasoned wood, or logs overhanging the front fence will
cause the glass to blacken.
b) The airwash relies on a supply of heated air to keep the glass clean,
therefore, when lighting the stove allow the firebed to become well
established before closing the air control. This may also be necessary
when re-fuelling the stove.
c) When re-fuelling keep the fuel as far back from the front fence as
possible, do not try to fit too much fuel into the firebox.
d) Do not completely close the air control.
It is always more difficult to keep the glass clean when running the
stove very slowly for long periods.
If blackening of the glass still occurs check that all flue connections
and the blanking plate are well sealed. It is also important that the
chimney draw is sufficient and that it is not affected by down-draught.
When the chimney is warm a draught reading of at least 1.25 mm
(0.05 in.) water gauge (12Pa) should be obtained. Some blackening
of the glass may occur below the level of the fuel retainer. This will
not obscure the view of the fire or affect its performance.
Fume Emission
Warning Note:
Properly installed and operated this appliance will not emit fumes.
Occasional fumes from de-ashing and re-fuelling may occur.
Persistent fume emission is potentially dangerous and must not be
tolerated. If fume emission does persist, then the following
immediate actions should be taken:
a) Open doors and windows to ventilate the room and then leave
the premises.
b) Let the fire out and safely dispose of the fuel from the
appliance.
c) Check for flue or chimney blockage, and clean if required.
d) Do not attempt to re-light the fire until cause of fuming has
been identified, if necessary seek professional advice.
The most common cause of fume emission is flueway or chimney
blockage. For your own safety these must be kept clean.
Fire blazing out of control
Check that:
a) The door is tightly closed.
b) The air control slider is fully closed.
c) A suitable fuel is being used.
d) Door seals and air slide are intact.
Chimney Fires
If the chimney is thoroughly and regularly swept, chimney fires should
not occur. However, if a chimney fire does occur close the air control,
and tightly close the door of the appliance. This should cause the
chimney fire to go out in which case the controls should be kept
closed until the stove has gone out. The chimney and flueways should
then be cleaned. If the chimney fire does not go out when the above
action is taken then the fire brigade should be called immediately.
After a chimney fire the chimney should be carefully examined for
any damage. Expert advice should be sought if necessary.
CO ALARM
Your installer should have fitted a CO alarm in the same room as the
appliance. If the alarm sounds unexpectedly, follow the instructions
given under “Warning Note” above.
IF YOU NEED FURTHER HELP
If you need further help with your Charnwood then your Installer will
be able to provide the answers to most questions. Your Local
Charnwood Premier Dealer has a great deal of experience and will
also be able to provide helpful advice. Further help is available from
the Charnwood Customer Services department who will be pleased
to give advice, if necessary.
9
®
OPERATING INSTRUCTIONS

UNPACKING THE STOVE
The stove arrives bolted and strapped to its pallet. There must be
adequate facilities for unloading and manoeuvring into position The
wrapping is first removed, then the stove released from the pallet by
removing 4 pallet bolts using a 10mm spanner. The pallet brackets
can now be removed from the stove by tilting it and using a 13mm
spanner to remove the bolts. The pallet is intended to be cut up and
used for kindling fuel.
Please take care when installing the stove that the requirements of
the Health and Safety at Work Act 1974 are met.
HEALTH AND SAFETY PRECAUTIONS
Some types of fire cement are caustic and should not be allowed to
come into contact with the skin. In case of contact wash with plenty
of water.
If there is a possibility of disturbing any asbestos in the course of
installation then please use appropriate protective equipment.
There must not be an extractor fan fitted in the same room as the
stove as this can cause the appliance to emit fumes into the room.
There must be an adequate air supply into the room in which the
appliance is installed to provide combustion air. The combustion air
supply must be via a permanently open vent. The requirement for
minimum free area is partly dependent on the design air permeability
of the house. In older properties the air permeability will be above
5.0m³/(h.m²), but in some modern properties it may be less. The
vent must be positioned such that it is not liable to blockage.
Minimium areas are given in the following table:
A fixed ducted air supply may be used as an alternative to the
traditional method of using a permanent open vent into a room to
supply air for combustion.
Ducted external air supply kits are available please contact
Charnwood for more information.
The ducted air kit is connected to the 100mm spigot on the
underside of the stove. If the stove is installed directly on a hearth,
without any additional stands, the ducted air supply will need to be
set into the floor with appropriate protection.
10
®
INSTALLATION INSTRUCTIONS
This stove is capable of intermittent operation, and is not suitable for
use in a shared flue system.
In addition to these instructions the requirements of BS.8303 and
BSEN 15287-1:2007 must be fulfilled. Local Authority Bylaws and
Building Regulations, including those referring to national and
European Standards, regarding the installation of Solid Fuel burning
appliances, flues and chimneys must also be observed.
CO ALARMS
Building regulations require that whenever a new or replacement
fixed solid fuel or wood/biomass appliance is installed in a dwelling a
carbon monoxide alarm must be fitted in the same room as the
appliance. Further guidance on the installation of the carbon
monoxide alarm is available in BS EN 50292:2002 and from the
alarm manufacturer's instructions. Provision of an alarm must not be
considered a substitute for either installing the appliance correctly or
ensuring regular servicing and maintenance of the appliance and
chimney system.
The outputs in the table are based on a 45 minute re-fuelling cycle
burning seasoned hardwood logs. All tests are carried out in
accordance with BSEN 13240.
In order for the appliance to perform satisfactorily the chimney height
must not be less than 4 metres measured vertically from the outlet of
the stove to the top of the chimney. The internal dimensions of the
chimney should preferably be 150-200 mm (6"- 8") either square or
SPECIFICATION
CHIMNEY
Air permeability
m³/(h.m²)
Minimum vent area cm²(in²)
Bay BX
>5.0
not required
<5.0
27.5 (4.3)
Bay BX
Output
5kW
(17,061BTU/h)
Mass
94.3kg
Flue Gas Temperature
279°C
Flue Gas Mass Flow
4.1g/s
Average Refuelling Cycle
0.75hrs
Maximum Log Size
Length 480mm
Diameter 75mm
Side
Back
Minimum distance from
combustibles mm
Uninsulated Flue
150
270
Minimum distance from
combustibles mm
Insulated Flue
100
130

round and MUST NOT BE LESS THAN 150 mm (6").
If an existing chimney is to be used it must be swept and checked, it
must be in good condition, free from cracks and blockages, and
should not have an excessive cross sectional area. If it was previously
used by an open fire then the chimney should be swept one month
after installation to clear any soot falls which may have occurred due
to the difference in combustion between the stove and the open fire.
If you find that the chimney is in poor condition then expert advice
should be sought regarding the necessity of having the chimney lined.
If it is found necessary to line the chimney then a lining suitable for
Solid Fuel must be used.
If there is no existing chimney then a prefabricated block chimney or
a twin walled insulated stainless steel flue to BSEN 15287-1:2007 can
be used either internally or externally. These chimneys must be fitted
in accordance with the manufacturers instructions and Building
Regulations.
Single wall flue pipe is suitable for connecting the stove to the
chimney but is not suitable for using for the complete chimney. If it is
found that there is excessive draw in the chimney then a draught
stabiliser should be fitted.
It is important that there is sufficient draw in the chimney and that
the chimney does not suffer from down-draught. When the chimney
is warm the draw should be not less than 1.25mm (0.05") water
gauge (12 Pa). If in doubt about the chimney seek expert advice.
HEARTH AND FIRE SURROUND
The stove must stand on a fireproof hearth and must not be situated
closer than the minimum distance from combustible materials (see
specification table) to the sides or rear above hearth level unless
adequately fireproofed in accordance with local building regulations.
The hearth must be of fireproof material and at least 12mm (1/2in.)
thick. The positioning of the stove and the size of the hearth are
governed by building regulations for Class 1 appliances. These
building regulations state that the hearth must extend in front of the
stove by at least 225mm (9 in.) and to the sides of the stove by at
least 150mm (6 in.). When the fire door is open, it extends beyond
the flat front of the stove by 436mm.
If in doubt as to the positioning of the stove, expert advice should be
sought either from the supplier or the local building inspector. The
fireplace must allow good circulation of air around the appliance to
ensure that maximum heat is transferred to the room and also to
prevent the fireplace from overheating. A gap of 150mm (6") each
side and 300mm (12") above the appliance should give sufficient air
circulation. If a wooden mantelpiece or beam is used in the fireplace it
should be a minimum of 460mm (18"), and preferably 600mm (24")
from the appliance. In some situations it may be necessary to shield
the beam or mantelpiece to protect it.
In order for the fire to operate correctly and to allow for access,
there must be an air gap behind the appliance of at least 50mm, but
be aware that this distance will need to be greater in some cases to
meet Building Regulation requirements.
The appliance should be installed on a floor with adequate load-
bearing capacity. If an existing construction does not meet this
requirement then please take suitable measures to achieve this. (e.g.
load distributing plate.)
This may be stainless steel, cast iron, or thick wall steel pipe. Straight
lengths of Charnwood Pipe to match the stove are available if
required.
Soot doors may either be in the actual brickwork of the
CONNECTIONS TO FLUES
SOOT DOORS
The stove must be connected to the flue using flue pipe of 150mm
(6") diameter.
The chimney may be swept through the appliance.
Horizontal lengths of flue must be kept to a minimum and should not
be more in length than the flue diameter.
It is possible to pass a 16 inch diameter sweeps brush through the
appliance.
11
®
INSTALLATION INSTRUCTIONS
Register Plate With
Soot Door
Alternative
Soot Door Positions
Fig. 9 Horizontal Register Plate With Top Flue Connection

12
®
INSTALLATION INSTRUCTIONS
chimney or in the register plate. Positions of soot doors are shown in
Fig. 9.
Ensure that the throat plate is fitted in the roof of the appliance. The
location and positioning of the throat plate is shown in Fig. 8.
Check that the front fence is fitted correctly and that the door closes
properly.
On completion of the installation allow a suitable period of time for
the fire cement and mortar to dry out before lighting the fire. Make a
layer of ash or sand on the base of the stove before lighting. Check to
ensure that smoke and fumes are taken from the appliance up the
chimney and emitted safely. Also check all joints and seals. On
completion of the installation and commissioning please leave the
operating instructions with the customer and advise them on the use
of the appliance.
PRE LIGHTING CHECK
COMMISSIONING

Model
Bay BX
EC Certificate of conformity no:
JT44-CPD-2016
Fuel type
WOOD LOGS
Space heating thermal output
5 kW
Emission of CO in combustion
products:
0.10%
Mean flue gas temperature:
279°C
Energy efficiency:
81%
Minimum distance to
combustible materials with
Uninsulated flue
Side:
Rear:
Minimum distance to
combustible materials with
Insulated flue
Side:
Rear:
150mm
270mm
100mm
130mm
13
EN13240:2001
ROOMHEATERS FIRED BY SOLID FUEL
A Division of A.J.Wells & Sons Limited Registered in England No. 03809371
16
Bishops Way, Newport, Isle of Wight PO30 5WS, United Kingdom
A.J WELLS & SONS LTDA.J WELLS & SONS LTD
CE Certificate for compliance with EN13240:2001

®
DIMENSIONS (mm)CHARNWOOD BAY BX
Store Stand Centre Stand Bench Stand
Side View
Plan View
Standard Model Rear View Side View

Item Part No. Description Item Part No. Description
1 001/XR010 Firebox 28 004/XR072 Air Control Plate
2# 002/BT001/A Door Assembly 29 008/XR073 Air Control Gasket
3 006/BT018 Glass 30 004/MR044 Latch Plate
4 008/MR047 Handle Pivot Boss 31 002/XR020 Lower Hinge Bracket
5# 005/BT023 Glass Trim 32 010/XR011 Convection Casing
6 008/XR076 Door Seal 33 004/JT049 Outer Casing
7 008/FFS046 M6x20 CSK Allen Screw 34 004/MR060 Air Duct Cover
8 008/FFW027 M10 Wavy Washer 35 004/JT025 Screen Top
9 008/FFW007 M10x19 Washer 36 004/JT029 Screen Lower
10 010/MR038 Handle Assembly 37 002/MR017 Fence
11 011/MR031S Set of Baffle Firebricks 38 010/MR078 Ash Barrier
12 011/XR030S Set Base, Back & Side Bricks 39 010/XR098 6" Lower Flue Adaptor
13 004/XR008 Back Brick Bracket 40 010/JT096 6" Upper Flue Adaptor
14 010/XR087 Throat Plate Support Bracket 41# 002/CH12B Flue Collar
15 004/XR025 Side Brick Bracket 42 010/MR126 100mm Spigot Assy
16 004/JT052 Rear Fixing Bracket 43 004/GR090 Fastener Retainer
17 010/JT035 Table Top Plinth 44 010/XR085 Roller
18 004/XR055 Air Slide Cover 45 008/FFP006 R-Pin
19 008/XR063 Air Box Upper Gasket 46 010/BT043 Upper Hinge Spacer
20 004/XR007 Air Control Slider 47 010/XR041 Upper Hinge Bracket
21 004/XR064 Control Rod 48 010/XR042 Hinge Spacer
22 008/FFM056 Rod End 49 008/FFR016 Hinge Pin
23 008/BR052 Felt Washer 50 012/JT011 Serial No Label
24 010/XR022 Air Slide Control Handle 51 010/XR088 Ash Scoop
25 004/XR058 Clicker Assembly 52# 010/JT034 Centre Stand
26 008/XR062 Airbox Lower Gasket 53# 010/JT070 Bench Stand
27 008/XR012 Control Knob 54# 010/JT071 Store Stand
* These items are not shown on the drawing
# Please specify colour when ordering.
To obtain spare parts please contact your local stockist
giving Model, Part No. and Description. In case of
difficulty contact the manufacturer at the address
shown.
This drawing is for identification purposes only.
Issue A
®
CHARNWOOD BAY BX PARTS LIST
15

A D i v i s i o n o f A . J . W e l l s & S o n s L i m i t e d R e g i s t e r e d i n E n g l a n d N o . 0 3 8 0 9 3 7 1
charnwood
T : + 4 4 ( 0 ) 19 8 3 5 3 7 7 7 7 • F : + 4 4 ( 0 ) 19 8 3 5 3 7 7 8 8 • C O N TA C T U S A T W W W . C H A R N W O O D . C O M
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
y o u r p r e m i e r d e a l e r
®