Chauvet Arena 3000 User manual

3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] –[phone]
FAX [phone]
www.chauvetlighting.com
Arena™3000
USER MANUAL
Snapshot
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Resettable breaker
User Serviceable
Duty Cycle

Arena™ 3000 User Manual 2 1/8/2009 11:40 AM
TABLE OF CONTENTS
1. Before You Begin................................................................................................................................3
What is included .......................................................................................................................................3
Unpacking Instructions..............................................................................................................................3
AC Power.................................................................................................................................................3
Contact Us................................................................................................................................................3
Safety Instructions ....................................................................................................................................4
2. Introduction......................................................................................................................................... 4
Features...................................................................................................................................................4
DMX Channel Summary............................................................................................................................4
Product Overview......................................................................................................................................5
3. Setup................................................................................................................................................... 6
Breaker Reset...........................................................................................................................................6
Fixture Linking..........................................................................................................................................6
Data Cabling.............................................................................................................................................6
DMX Data Cable.......................................................................................................................................6
Cable Connectors.....................................................................................................................................7
3-Pin to 5-Pin Conversion Chart ................................................................................................................7
Setting up a DMX Serial Data Link.............................................................................................................8
Master/Slave Fixture Linking .....................................................................................................................8
Mounting ..................................................................................................................................................9
Orientation................................................................................................................................................9
Rigging.....................................................................................................................................................9
4. Operating Instructions...................................................................................................................... 10
Operation ............................................................................................................................................... 10
DMX Mode .............................................................................................................................................10
DMX Channel Values.............................................................................................................................. 10
Wired timer remote with LCD screen........................................................................................................ 11
Auto cut-off feature ................................................................................................................................. 11
Wireless Controller (FC-W) (Optional)...................................................................................................... 12
Setting the starting address..................................................................................................................... 13
General Troubleshooting......................................................................................................................... 13
Technical Support................................................................................................................................... 13
5. Appendix........................................................................................................................................... 14
DMX Primer............................................................................................................................................14
Returns Procedure.................................................................................................................................. 14
Claims.................................................................................................................................................... 14
Technical Specifications.......................................................................................................................... 16

Arena™ 3000 User Manual 3 1/8/2009 11:40 AM
1. BEFORE YOU BEGIN
What is included
1 x Arena™3000
Warranty Card
User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the
source voltage matches the fixture’s requirement. Check the fixture or device carefully to make sure
that if a voltage selection switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line voltage applied.
Damage to your fixture may result if the line voltage applied does not match the
voltage indicated on the voltage selector switch. All fixtures must be connected to
circuits with a suitable Earth Ground.
Contact Us
World Wide
General Information CHAUVET
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com

Arena™ 3000 User Manual 4 1/8/2009 11:40 AM
Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
2. INTRODUCTION
Features
1-channel DMX-512 fog machine
Additional Features
Dual output nozzles
3-pin and 5-pin DMX connections
Wired timer remote with LCD screen
Manual fog button
9L tank capacity
13 minute heat up
Water-based fogger
OPTIONS
Wireless remote (FC-W)
DMX Channel Summary
CHANNEL
FUNCTION
1
Fog output
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this product.

Arena™ 3000 User Manual 5 1/8/2009 11:40 AM
Product Overview
DMX out
3-pin
Bracket
adjustment
knob
Hanging
bracket
Manual
fog
button
Power input
DMX in
3-pin
Breaker
Power switch
DMX in
5-pin
Remote
control
DMX out
5-pin
Wired timer remote
with LCD screen
Safety
Carrying
handle
Carrying
handle

Arena™ 3000 User Manual 6 1/8/2009 11:40 AM
3. SETUP
Breaker Reset
This product is equipped with a breaker on the main power input, located on the exterior of the back
panel. In the event that this breaker trips, you may reset it very easily.
1. Unplug the product from the mains power.
2. Allow to cool for 5-15 minutes.
3. Using your hand, press on the button for the breaker, until it remains in place.
Note: In the event that this breaker will not reset, contact CHAUVET for troubleshooting.
The fixture may need to be serviced.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors –30 pF/ft.
Maximum capacitance between conductor and shield –55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 –140 ohms
Disconnect the power cord before replacing a fuse and
always replace with the same size fuse
same type fuse.

Arena™ 3000 User Manual 7 1/8/2009 11:40 AM
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART
Conductor
3 Pin Female (output)
5 Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - ) signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Pin 4
Do not use
Pin 5
COMMON
DMX +
DMX -
INPUT
OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors. To
avoid signal transmission problems and
interference, it is always advisable to
connect a DMX signal terminator.
3-pin DMX connector
configuration
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
5-pin DMX connector configuration

Arena™ 3000 User Manual 8 1/8/2009 11:40 AM
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
Universal DMX Controller
Continue the link
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via either
settings in the control panel or DIP-
switches. Secondarily, the fixtures
that follow may also require a slave
setting. Please consult the
“Operating Instructions” section in
this manual for complete instructions
for this type of setup and
configuration.
Master
Slave
Slave
Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft
Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.

Arena™ 3000 User Manual 9 1/8/2009 11:40 AM
Hanging Clamp
Note!
Clamp is sold separately.
Mounting
ORIENTATION
This fixture may be mounted in a 90° degree angle only (horizontal), provided there is adequate room for
ventilation.
RIGGING
It is important never to obstruct the fan or vents pathway. Mount the fixture
using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by
loosening both knobs and tilting the fixture. After finding the desired position,
retighten both knobs.
When selecting installation location, take into consideration fluid
tank access and routine maintenance.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes, or restricted ventilation.

Arena™ 3000 User Manual 10 1/8/2009 11:40 AM
4. OPERATING INSTRUCTIONS
Operation
DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer in the Appendix of this manual.
1) This fixture will automatically switch to DMX mode operation, once a DMX controller has been
plugged into the 3-pin or 5-pin DMX input.
DMX Channel Values
CHANNEL
VALUE
FUNCTION
1
000 005
006 255
Fog output
No function
Fog output 0%~100%

Arena™ 3000 User Manual 11 1/8/2009 11:40 AM
Wired timer remote with LCD screen
This fixture comes standard with a wired LCD remote. This has the function of manually
controlling the product. Or, you can set it to timer function. See the below menu structure for
operating this.
BUTTON
FUNCTION
+
Increases the value of the item selected on screen
-
Decreases the value of the item selected on screen
FUNCTION
Moves the selection cursor to the next item on the screen
TIMER
Activates the timer function, based on the interval, duration,
and value settings that have been set
LOCK
Locking output button; amount of fog output is determined
by the Volume setting
OUTPUT
Momentary full output button
DISPLAY
FUNCTION
VALUE
DESCRIPTION
IN
Interval
0~99
Sets the time between output (in minutes)
DU
Duration
0~99
Sets the duration of output (in seconds)
VO
Volume
0~20
Sets the volume of output for Lock function
ADD
Address
0~512
Sets the DMX address
Auto cut-off feature
This product has an auto cut-off safety feature to keep the machine form becoming damaged. This is referring to the
operation of the pump. When the fluid tank is empty, the pump will still operate for a short period. Then, it will sense that
there is no fluid, and more fluid will have to be added. An indication that this has occurred is the blue LED’s lighting the
fluid tank flashing.
Note: it will take approximately 1 minute for this feature to engage once the fluid has emptied form the tank.
Note: once the tank has been refilled with fog fluid, you must momentarily turn the fixture off, and then back on in order to
reset the safety feature.
Lock
button
Timer
button
Output
button
Function
button

Arena™ 3000 User Manual 12 1/8/2009 11:40 AM
Wireless Controller (FC-W) (Optional)
This mode will allow you to control the fogger using the optional wireless controller. This consists of the
transmitter and the receiver. You may control up to 4 independent fog machines or many more if you run them
simultaneously. See the below instructions on setting up your fogger to operate with the FC-W.
1. Plug the wires receiver into the fog machine 5-pin port labeled “Remote Control”.
2. There are 4 buttons on the wireless remote transmitter which act as triggers. Each button can be assigned to a
different fog machine. You may only choose 1 dipswitch on each receiver. See the below configuration for
setting the receivers to operate with the transmitter remote.
Mode Dipswitches
CH1 1 = On, 2-4 = Off
CH2 2 = On, 1,3,4 = Off
CH3 3 = On, 1,2,4 = Off
CH4 4 = On, 1,2,3 = Off
3. Press the fog button, and the fog machine will output fog for as long as you hold down the button.
Wireless
Receiver
LED indicator
(heating)
LED indicator
(ready)
Dipswitches
Wireless
Transmitter
Fog
Triggers

Arena™ 3000 User Manual 13 1/8/2009 11:40 AM
SETTING THE STARTING ADDRESS
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address"
from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, afixture that uses 6 DMX channels and was addressed to start on
DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start addresses
so that the channels used do not overlap, and note the start address selected for future reference.
If this is your first time addressing a fixture using the DMX-512 control protocol, we suggest jumping to the
Appendix Section and reading the heading “DMX Primer”. It contains very useful information that will help you
understand its use.
General Troubleshooting
Symptom
Solution(s)
Applies to
Lights
Foggers
& Snow
Controllers
Dimmers
& Chaser
Loss of signal
Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power cables
or black lights.




Remote does not
work
Make sure connector is firmly connected to device


If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support at the location listed below.
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): [e-mail]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com

Arena™ 3000 User Manual 14 1/8/2009 11:40 AM
5. APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).
Products returned without an RMA # will be refused. Call CHAUVET and request RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from
inadequate packaging is the customer’s responsibility. CHAUVET reserves the right to use its own
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is
always a safe method to use.
Note: If you are given an RMA #, please include the following information on a piece of
paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

Arena™ 3000 User Manual 15 1/8/2009 11:40 AM
WARNING!
`Note: All fog machines are prone to clogging due to the thick consistency of fog
liquid and the high temperature at which it vaporizes. However, a properly maintained
fog machine should provide years of reliable use. Cleaning your fog machine
regularly will help reduce costly replacement and repair charges.
Maintenance
Do not allow the fog machine to become contaminated. After every 40 hours of continuous
operation, it is recommended to run a cleaning solution composed of 80% distilled water and 20%
distilled vinegar through the system to prevent the accumulation of particulate matter in the
heating element.
The recommended cleaning regimen is as follows:
1. Empty all fog liquid from the machine. Add cleaning solution to tank. Plug unit in and
begin warm up.
2. Run the unit in a well-ventilated area until the tank is almost empty. Do not allow the
pump to run dry.
3. Replace nozzle.
4. Cleaning is now complete. Refill with fog liquid. Run the machine briefly to clear any
cleaning solution from the pump and heater.
5. Do not operate the machine without liquid at any time.
Storage
1. When storing run distilled water (not tap water) through the system as described in the
cleaning regiment above. This will help avoid any particles condensing inside the pump
or heater.
2. It is strongly recommended to test-run the machine on a monthly basis in order to
achieve its best fogging condition.
Caution:
1. Never place the fog/hazer machine on any flammable material (i.e. carpet, fabric etc.)
during operation. All fog/hazer machines should always be on a non-flammable surface,
such as concrete or tile.
2. Depending on the amount of fog/haze generated, all fog machines may set off smoke
detectors.

Arena™ 3000 User Manual 16 1/8/2009 11:40 AM
Technical Specifications
WEIGHT & DIMENSIONS
Length .............................................................................................................................. 26.5 in (673 mm)
Width................................................................................................................................ 19.6 in (430 mm)
Height...............................................................................................................................10.6 in (270 mm)
Weight..............................................................................................................................31.6 lbs (14.3 kg)
POWER
AC power (voltage specific) ..................................................................115VAC 60Hz or 230VAC 50Hz
Breaker size (115V).....................................................................................................................15A 125V
Breaker size (230V).......................................................................................................................9A 250V
Power Consumption .......................................................................................1,560W (13A) max @ 120V
Inrush Power......................................................................................................................(15.4A) @ 120V
Power Factor...........................................................................................................................0.99 @ 120V
Output .........................................................................................................................................30,000cfm
Fluid consumption.......................................................................................................................200ml/min
THERMAL
Maximum ambient temperature .............................................................................................104°F (40°C)
CONTROL & PROGRAMMING
Data input................................................................................................... locking 3-pin XLR male socket
Data output ............................................................................................. locking 3-pin XLR female socket
Data pin configuration (3-pin).....................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Data input................................................................................................... locking 5-pin XLR male socket
Data output ............................................................................................. locking 5-pin XLR female socket
Data pin configuration (5-pin)............. pin 1 shield, pin 2 (-), pin 3 (+), pin 4 (not used), pin 5 (not used)
Protocols...........................................................................................................................DMX-512 USITT
DMX Channels...........................................................................................................................................1
ORDERING INFORMATION
Arena™3000..........................................................................................................................ARENA3000
Wireless remote...................................................................................................................................FCW
WARRANTY INFORMATION
Warranty..................................................................................................................2-year limited warranty