Chauvet COLORdash Batten-Quad 6 User manual

User Manual

Edition Notes
COLORdash™ Batten-Quad 6 User Manual Rev. 2
Edition Notes
The COLORdash™ Batten-Quad 6 User Manual Rev. 2 covers the description, safety
precautions, installation, programming, operation, and maintenance of the
COLORdash™ Batten-Quad 6. CHAUVET® released this edition of the
COLORdash™
Batten-Quad 6 User Manual in November 2012.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the CHAUVET® name and
the
dotted triangle, and all other trademarks in this manual pertaining to services, products,
or marketing statements (example: It’s Green Thinking™
) are owned or licensed by
CHAUVET®. Any other
product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this User Manual in its entirety, including but not limited
to pictures, logos, trademarks, and resources.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Use
CHAUVET® authorizes its customers to download and print this manual for professional
information purposes only. CHAUVET® expressly prohibits the u
sage, copy, storage,
distribution, modification, or printing of this manual or its con
tent for any other purpose
without written consent from CHAUVET®.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-
sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content
accordingly.
Intended Audience
Any person in charge of installing, operating, and/or maintaining this product should
completely read through the guide that shipped with the product, as well as this manual,
before installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any errors or omissions
in this document. CHAUVET® reserves the right to revise and make changes to the
content of this document without obligation that CHAUVET®
notify any person or
company of such revision or changes. This does not in any way constitute a
commitment by CHAUVET® to make such changes. CHAUVET® may issue a revision
of this manual or a new edition to incorporate such changes.
Document Revision
The COLORdash™ Batten-Quad 6 User Manual Rev. 2 supersedes all previous
versions of this manual. Discard any older versions of this manual you may have,
whether in printed or electronic format, and replace with this version.
Author
Date
Editor
Date
D. Couppe
11/6/12
S. Diaz
11/6/12

Table of Contents
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included.................................................................................................................................................... 1
Claims..................................................................................................................................................................................1
Manual Conventions.............................................................................................................................................................1
Symbols...............................................................................................................................................................................1
Product at a Glance ............................................................................................................................................... 2
Safety Notes.......................................................................................................................................................... 2
Personal Safety....................................................................................................................................................................2
Mounting and Rigging...........................................................................................................................................................2
Power and Wiring .................................................................................................................................................................2
Operation.............................................................................................................................................................................2
Expected LED Lifespan.......................................................................................................................................... 2
2. Introduction...............................................................................................................................................3
Product Description................................................................................................................................................ 3
Features ................................................................................................................................................................ 3
Product Overview................................................................................................................................................... 4
Product Dimensions............................................................................................................................................... 5
3. Setup..........................................................................................................................................................6
AC Power .............................................................................................................................................................. 6
AC Plug................................................................................................................................................................................6
Fuse Replacement................................................................................................................................................................6
Power Linking........................................................................................................................................................ 7
DMX Linking .......................................................................................................................................................... 7
DMX Modes..........................................................................................................................................................................7
Master/Slave Connectivity.....................................................................................................................................................7
Mounting................................................................................................................................................................ 8
Orientation............................................................................................................................................................................8
Rigging.................................................................................................................................................................................8
4. Operation...................................................................................................................................................9
Control Panel Description....................................................................................................................................... 9
Control Options...................................................................................................................................................... 9
Programming......................................................................................................................................................... 9
DMX Personality...................................................................................................................................................................9
DMX Control.........................................................................................................................................................................9
Static Color.........................................................................................................................................................................10
Auto Programs....................................................................................................................................................................10
Auto Test............................................................................................................................................................................10
Master/Slave ......................................................................................................................................................................10
Dimmer Curves...................................................................................................................................................................11
Software Information...........................................................................................................................................................11
Fixture Hours......................................................................................................................................................................11
Backlite ..............................................................................................................................................................................11
White Balance ....................................................................................................................................................................11
Menu Map.............................................................................................................................................................12
DMX Values..........................................................................................................................................................13
DMX Values (cont.)...............................................................................................................................................14
DMX Values (cont.)...............................................................................................................................................15
5. Technical Information.............................................................................................................................16
Product Maintenance............................................................................................................................................16
Returns.................................................................................................................................................................16
Technical Specifications........................................................................................................................................17
Contact Us............................................................................................................................................................18

Before You Begin
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -1-
1. Before You Begin
What Is Included
•COLORdash™ Batten-Quad 6
•Power Cable
•Warranty Card
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts
are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify th
e carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shippin
g,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text Conventions
Convention
Meaning
1~512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1~10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols Meaning
Critical installation, configuration, or operation information.
Failure to comply with this information may cause the product not
to work, damage third-party equipment, or cause harm to the
operator.
Important installation or configuration information. Failure to
comply with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.

Before You Begin
-2- COLORdash™ Batten-Quad 6 User Manual Rev. 2
Product at a Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-Ranging Power
Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Read all the following Safety Notes before working with this product. These notes
include important information about the installation, usage, and maintenance of this
product.
This product contains no user-serviceable parts. Any reference to servicing in
this User Manual will only apply to properly
trained CHAUVET® certified
technicians. Do not open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this
product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting and
Rigging
•Do not operate this product outdoors or in any location where dust, excessive heat,
water, or humidity may affect it.
•Make sure there are no flammable materials close to this product while it is
operating.
•When hanging this product, always secure to a fastening device using a safety
cable (included).
Power and Wiring
•Always make sure you are connecting this product to the proper voltage in
accordance with the specifications in this manual or on the product’s specification
label.
•Never connect this product to a dimmer pack or rheostat.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables.
Have the damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 104° F (40° C). Do not operate this product
at a higher temperature.
•
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single-LED
conditions. For this reason, using clustered LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be 40,000 to
50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product and reducing the ambient temperature to
an optimal operating range. In addition, limiting the overall projection intensity may also
help to extend the LEDs’ lifespan.

Introduction
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -3-
2. Introduction
Product Description
The COLORdash™ Batten-Quad 6 is a high-power quad color RGBA LED-based linear
wash light. It consists of a rectangular housing with 6 quad-colored
LEDs arranged in a
single row. It comes with a hanging bracket and adjustable side brackets
for floor
mounting.
Features
•4-, 6-, 10-, 24-, or 28-channel quad-colored LED wash product
•Operating modes:
•4-channel: RGBA
•6-channel: RGBA, dimmer, strobe
•10-channel: RGBA, dimmer, strobe, macro, auto, dim mode, auto speed
•24-channel: RGBA control per quad-color LED
•28-channel: RGBA per pixel, dimmer, strobe, auto, auto speed
•Silent, flicker-free operation
•Individual pixel control
•Maintain pixel pitch end to end or stacking
•16-bit dimming with selectable dimming curves
•All metal construction for added durability

Introduction
-4- COLORdash™ Batten-Quad 6 User Manual Rev. 2
Product Overview
Front View
Rear View
Side View
End View

Introduction
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -5-
Product Dimensions

Setup
-6- COLORdash™ Batten-Quad 6 User Manual Rev. 2
3. Setup
AC Power
Each COLORdash™ Batten-Quad 6 has an auto-ranging power supply that works with
an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power
requirements for each COLORdash™ Batten-Quad 6
, refer to the label affixed to the
product. You can also refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during nor
mal operation.
For more information, download Sizing Circuit Breakers from the CHAUVET® website
:
www.chauvetpro.com.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The COLORdash™ Batten-Quad 6 comes with a power input cord terminated with an
IEC connector on one end and an Edison plug on the other end (U.S.
market). If the
power input cord that came with your product has no plug or you need to change the
Edison plug, use the table below to wire the new plug.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace with a fuse of the same type and rating.
Fuse Replacement
1. Disconnect the product from the power outlet.
2. Using a flat-head screwdriver, wedge the tip into the slot of the fuse holder.
3. Pry the safety cap out of the housing to pull out the installed fuse.
4. Remove the blown fuse from the safety cap and replace with a fuse of the exact
same type and rating (T 2 A, 250 V).
5. Insert the fuse holder back in place and reconnect the power.
Installed fuse
(held by plastic clip)
Spare fuse
(inside safety cap)
Safety cap

Setup
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -7-
Power Linking
The COLORdash™ Batten-Quad 6 supports power linking. You can power link up to 17
products at 120 VAC, 30 products at 208 VAC, or 33 products at 230 VAC.
This product comes with a
power input cord. This product does not come with a power
linking cable; however, a power linking cable is available as an option.
DMX Linking
You can link the COLORdash™ Batten-Quad 6 to a DMX controller using a standard
DMX serial connection. If using other DMX compatible products with the
COLORdash™
Batten-Quad 6, you can control each individually with a single DMX controller.
DMX Modes
The COLORdash™ Batten-Quad 6 uses the standard DMX data connection for the 4-,
6-, 10-, 24-, and 28-channel DMX modes.
•Refer to the Introduction chapter for a brief description of these modes.
•Refer to the Operation chapter to learn how to configure the COLORdash™ Batten-
Quad 6 to work in these modes.
•The DMX Values
section will provide you with detailed information regarding the DMX
modes.
Master/Slave
Connectivity
The Master/Slave mode allows a COLORdash™ Batten-Quad 6 (the “master product”)
to control one or more COLORdash™ Batten-Quad 6
s (the “slave products”) without a
DMX controller. One COLORdash™ Batten-Quad 6
becomes the master product when
running an Auto or Fixed program, or by being in Manual mode.
You must configure each slave product’s control panel to operate in SLAVE mode.
During Master/Slave operation, the slave products will operate in unison with the master
product.
DO NOT connect a DMX controller to products operating in Master/Slave mode.
The DMX controller signals may interfere with the signals from the master
product.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave products.
If you are not familiar with or need more information about DMX standards,
Master/Slave connectivity, or the DMX cables needed to link this produc
t to a DMX
controller, download the DMX Primer from the CHAUVET® website:
www.chauvetpro.com.

Setup
-8- COLORdash™ Batten-Quad 6 User Manual Rev. 2
Mounting
Before mounting this product, read and follow the Safety Notes in this manual.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
The COLORdash™ Batten-Quad 6 consists of a double-bracketed yoke and the body of
the product CHAUVET® recommends using the following general guidelines
when
mounting.
•When selecting an installation location, consider easy access to this product for
operation, programming adjustments, and routine maintenance.
•Make sure to mount this product away from any flammable material as indicated in
the Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•If hanging this product, make sure that the mounting location can support the
product’s weight. Refer to the Technical Specifications chart for the weight-bearing
requirements of this product.
•When hanging this product, always secure to a fastening device using a safety cable
(included).
Procedure
The COLORdash™ Batten-Quad 6 comes with a double-bracketed yoke to which you
can either attach mounting clamps for hanging or simply use as a floor stand. You must
supply your own mounting clamps. Make sure the clamps are capable of supporting the
weight of this product. Use at least one mounting point per product.
Product Mounting Diagram
Floor Mounting
Overhead Mounting
Clamp
Safety Cable

Operation
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -9-
4. Operation
Control Panel
Description
Button Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value in to the current function
<UP>
Navigates upward through the menu list and increases the
numeric value when in a function
<DOWN>
Navigates downward through the menu list and decreases the
numeric value when in a function
Control Options
You can set the COLORdash™ Batten-Quad 6 start address in the 001~512 DMX
range. This enables control of up to 18 products in the 28-channel 28 Ch personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main
level and a variable number of programming levels for each option.
•To go to the desired main level, press <MENU> repeatedly until the option shows on
the display. Press <ENTER> to select. This will take you to the first programming
level for that option.
•To select an option or value within the current programming level, press <UP> or
<DOWN> until the option shows on the display. Press <ENTER> to select. In this
case, if there is another programming level, you will see that first option, or you will
see the selected value.
•Press <MENU> repeatedly to exit to the previous main level.
DMX Personality
This setting allows you to choose a particular DMX personality.
1. Go to the Channel main level.
2. Select the desired personality (
4 Ch
,
6 Ch
,
10 Ch
,
24 Ch
, or
28 Ch
).
•See the DMX Values section for the highest starting address you can select for
each personality.
•Make sure that the starting addresses on the various products do not overlap
due to the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX
controller. All products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personality.
2. Set the running mode:
a. Go to the M&S Mode main level.
b. Select the Master programming level.
3. Set the starting address:
a. Go to Address main level.
b. Select the starting address (001~509).
The highest recommended starting address for each DMX mode are as follows:
DMX Mode DMX Address
4 Ch
509
6 Ch
507
10 Ch
503
24 Ch
489
28 Ch
485

Operation
-10- COLORdash™ Batten-Quad 6 User Manual Rev. 2
Static Color
The Static Color mode allows for permanent RGBA color mixing without a DMX
controller.
1. Go to the Static main level.
2. Select the Fix C.
a. Choose desired color combination.
3. Select the Manu C
a. Select Color (RGBA)
b. Select the desired color value (000~255).
c. Repeat for the other colors.
Auto Programs
Auto programs allow for dynamic RGBA color mixing without a DMX controller.
1. Go to AUTO Main Level.
2. Select the desired auto (Auto. 01~12).
3. Select Speed.
4. Choose the desired speed value (000~100).
You cannot edit any of the auto programs (AUTO 01~12).
Auto Test
This option allows you to test all the LEDs on the COLORdash™ Batten-Quad 6.
1. Go to Info Main Level.
2. Select
Auto > Test
.
Master/Slave
The Master/Slave mode allows a group of COLORdash™ Batten-Quad 6s (the slave
products) to simultaneously duplicate the output of another COLORdash™ Batten-Quad
6 (the master product) without a DMX controller.
1. Set each of the slave products:
a. Go to M&S Mode.
b. Select SLAVE.
2. Set the master product:
a. Set the running mode to Master as explained in DMX Control.
b. Select an Auto or Static program as explained in Auto Programs.
•The master product is the one that runs a program whether in Auto, or Static
Color mode.
•Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master
product.
•
The master product should be the first product in the daisy chain.

Operation
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -11-
Dimmer Curves
This setting determines how fast the output of the COLORdash™ Batten-Quad 6
changes when you modify the values of the Red, Green, Blue, White, and Dimmer
faders. This setting provides four different options to simulate the dimming curve of an
incandescent lighting product.
1. Go to the Dimmer Mode main level.
2. Select a dimmer curve (OFF, DIM1, DIM2, or DIM3).
OFF:
The output is proportional (linear) to the Dimmer and RGBA channel
values.
DIM1~3:
The output follows the Dimmer and RGBA channel values based on the
corresponding dimmer curve, being DIM1 the fastest and DIM3the
slowest.
Software Information
This option shows what version of software the COLORdash™ Batten-Quad 6 is
running.
1. Go to the Info main level.
2. Select Version. (the version number will show on the screen)
Fixture Hours
This option shows the total amount of hours the COLORdash™ Batten-Quad 6 has been
turned on.
1. Go to the Info main level.
2. Select FixHours (the hours will show on the screen).
Backlight
This setting allows you to set the amount of time the backlight on the COLORdash™
Batten-Quad 6 stays on after the last button is pressed on the control panel.
1. Go to the BackLite main level.
2. Select On, 10S, 20S, or 30S.
3. Press
<ENTER>
.
White Balance
This setting allows you to select the white color shown by the COLORdash™ Batten-
Quad 6 when the DMX controller’s Red, Green, and Blue faders are set to “255.”
1. Go to the White Balance main level.
2. Select a color (R, G, or B).
3. Select a color value (125~255).
4. Repeat for the other colors.
When selecting White Balance, you will only be able to define the values of Red,
Green, and Blue.
The values of Red, Green, and Blue configured from White Balance will define the
color temperature shown when the RGB faders are set to “255.”

Operation
-12- COLORdash™ Batten-Quad 6 User Manual Rev. 2
Menu Map
Main Level Programming Levels Description
Auto
Auto 1~12
Speed
0~100
5 automatic programs
Static
Fix C
R
Red
G
Green
B
Blue
A
Amber
GB
Green/Blue
RB
Red/Blue
RG
Red/Green
RGB
Red/Green/Blue
RA
Red/Amber
GA
Green/Amber
BA
Blue/Amber
RGA
Red/Green/Amber
RBA
Red/Blue/Amber
GBA
Green/Blue/Amber
RGBA
Red/Green/Blue/Amber
Manu C
R
Value 0~255 Combine red, green, blue, and amber to make a
custom color
G
B
A
Dim Mode
Off
No dimmer
DIM 1~3
Dimmer curve
BackLite
10S
Turns off backlight after 10 sec of inactivity
20S
Turns off backlight after 20 sec of inactivity
30S
Turns off backlight after 30 sec of inactivity
On
Display backlight always on
Info
Auto
Test
Turns on all LEDs in sequence for testing
FixHours
Shows total product hours
Version
Shows installed software version
Address
001~509
Selects DMX address
Channel
4 Ch
4-channel: R/G/B/A control
6 Ch
6-channel: R/G/B/A, dimmer, strobe
10 Ch
10-channel: R/G/B/A dimmer, strobe, color
macro, auto, dimmer speed, auto speed
24 CH
24-channel: R/G/B/A per quad-color LED
28 Ch
28-channel: R/G/B/A per quad-color LED,
dimmer, strobe, auto, auto speed
M&S Mode
Master
DMX mode
Slave
Slave mode
White Balance
R
Value 125~255
Sets red LED maximum value
G
Sets green LED maximum value
B
Sets blue LED maximum value

Operation
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -13-
DMX Values
28-Ch
Channel Function Value Percent/Setting
1
Red 1
000 255
0~100%
2
Green 1
000 255
0~100%
3
Blue 1
000 255
0~100%
4
Amber 1
000 255
0~100%
5
Red 2
000 255
0~100%
6
Green 2
000 255
0~100%
7
Blue 2
000 255
0~100%
8
Amber 2
000 255
0~100%
9
Red 3
000 255
0~100%
10
Green 3
000 255
0~100%
11
Blue 3
000 255
0~100%
12
Amber 3
000 255
0~100%
13
Red 4
000 255
0~100%
14
Green 4
000 255
0~100%
15
Blue 4
000 255
0~100%
16
Amber 4
000 255
0~100%
17
Red 5
000 255
0~100%
18
Green 5
000 255
0~100%
19
Blue 5
000 255
0~100%
20
Amber 5
000 255
0~100%
21
Red 6
000 255
0~100%
22
Green 6
000 255
0~100%
23
Blue 6
000 255
0~100%
24
Amber 6
000 255
0~100%
25 Auto Programs
000 010
011 030
031 050
051 070
071 090
091 110
111 130
131 150
151 170
171 190
191 210
211 230
231 250
251

255
No Function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Auto 11
Auto 12
Random Auto
26
Auto Speed
000 255
Slow to Fast
27
Dimmer
000 255
0~100%
28 Strobe
000 010
011 255
No Function
Slow to Fast

Operation
-14- COLORdash™ Batten-Quad 6 User Manual Rev. 2
DMX Values (cont.)
24-Ch
Channel Function Value Percent/Setting
1
Red 1
000 255
0~100%
2
Green 1
000 255
0~100%
3
Blue 1
000 255
0~100%
4
Amber 1
000 255
0~100%
5
Red 2
000 255
0~100%
6
Green 2
000 255
0~100%
7
Blue 2
000 255
0~100%
8
Amber 2
000 255
0~100%
9
Red 3
000 255
0~100%
10
Green 3
000 255
0~100%
11
Blue 3
000 255
0~100%
12
Amber 3
000 255
0~100%
13
Red 4
000 255
0~100%
14
Green 4
000 255
0~100%
15
Blue 4
000 255
0~100%
16
Amber 4
000 255
0~100%
17
Red 5
000 255
0~100%
18
Green 5
000 255
0~100%
19
Blue 5
000 255
0~100%
20
Amber 5
000 255
0~100%
21
Red 6
000 255
0~100%
22
Green 6
000 255
0~100%
23
Blue 6
000 255
0~100%
24
Amber 6
000 255
0~100%
4-Ch
Channel
Function
Value
Percent/Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4
Amber
000 255
0~100%

Operation
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -15-
DMX Values (cont.)
10-Ch
Channel Function Value Percent/Setting
1
Dimmer
000 255
0~100%
2
Red
000 255
0~100%
3
Green
000 255
0~100%
4
Blue
000 255
0~100%
5
Amber
000 255
0~100%
6 Strobe
000 010
011 255
No Function
Slow to Fast
7 Color Macro + White
Balance
000 010
011 030
031 050
051 070
071 090
091 110
111 130
131 150
151 170
171 200
201 205
206 210
211 215
216 220
221 225
226 230
231 235
236 240
241 245
246 250
251 255
No Function
R: 100% G: 0~100% B: 0
R: 100%~0 G: 100% B: 0
R: 0 G: 100% B: 0~100%
R: 0 G: 100%~0 B: 100%
R: 0~100% G: 0 B: 100%
R: 100% G: 0 B: 100%~0
R: 100% G: 0~100% B: 0~100%
R: 100%~0 G: 100%~0 B: 100%
R: 100% G: 100% B: 100% A: 100%
White 1
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
8 Auto Programs
000 051
052 101
102 152
153 203
204 254
255
No Function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
9
Auto Speed
000 255
Slow to Fast
10 Dimmer Speed
000 051
052 101
102 152
153 203
204 255
Preset dimmer speed from display menu
Linear dimmer
Nonlinear dimming curve 1 (fastest)
Nonlinear dimming curve 2
Nonlinear dimming curve 3(slowest)
6-Ch
Channel Function Value Percent/Setting
1
Dimmer
000 255
0~100%
2
Red
000 255
0~100%
3
Green
000 255
0~100%
4
Blue
000 255
0~100%
5
Amber
000 255
0~100%
6 Strobe
000 010
011 255
No Function
Slow to Fast

Technical Information
-16- COLORdash™ Batten-Quad 6 User Manual Rev. 2
5. Technical Information
Product
Maintenance
To maintain optimum performance and minimize wear, you should clean this product
frequently. Usage and environment are contributing factors in determining the cleaning
frequency.
As a rule, clean this product at least twice a month. Dust build-up reduces
light output
performance and can cause overheating. This can lead to reduced light source life and
increased mechanical wear.
To clean your product:
•Unplug the product from power.
•Wait until the product has cooled.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external vents and accessible internal components.
•Clean all external surfaces with a mild solution of non-ammonia glass cleaner or
isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Wipe any dirt or grime to the outside edges of the lens surface.
•Gently polish the lens surfaces until they are free of haze and lint.
Always dry the external surfaces thoroughly and carefully after cleaning them.
Returns
You must send the product prepaid, in the original box, and with the original packing and
accessories. CHAUVET® will not issue call tags.
Call CHAUVET®
and request a Return Merchandise Authorization (RMA) number
before shipping the product. Be pr
epared to provide the model number, serial number,
and a brief description of the cause(s) for the return.
Clearly label the package with an RMA number. CHAUVET®
will refuse any product
returned without an RMA number.
DO NOT write the RMA number directly on the box. Instead, write it on a properly
affixed label.
Once you have received the RMA number, include the following information on a piece
of paper inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem(s)
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. FedEx packing or double-boxing
are
recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).

Technical Information
COLORdash™ Batten-Quad 6 User Manual Rev. 2 -17-
Technical Specifications
Dimensions and
Weight
Length Width Height Weight
22 in (560 mm)
2.6 in (65 mm)
6.46 in (164 mm)
5 lbs (2.3 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Electrical
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
208 V, 60 Hz
230 V, 50 Hz
Consumption
90 W
94 W
96 W
Operating
.76 A
.45 A
.41 A
Power linking current
(products)
13.6 A
(17 products)
13.6 A
(30 products)
13.6 A
(33 products)
Fuse/Breaker
T 2 A, 250 V
T 2 A, 250 V
T 2 A, 250 V
Power I/O
U.S./Worldwide
Europe
Power input connector
IEC
IEC
Power output connector
Edison
Edison
Power cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
Quad-colored LEDs
5 W
50,000 hours
Color
Quantity
Current
Red
6
499 mA
Green
6
480 mA
Blue
6
468 mA
Amber
6
500 mA
Photo Optic
Parameter
Standard Optics
Illuminance @ 5 m
390.7 lux
Beam angle
17º
Field angle
33º
Thermal
Max. External Temperature
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3- and 5-pin XLR
Sockets
4, 6, 10, 24, 28
Ordering
Product Name Item Code Item Number
COLORdash™ Batten-Quad 6
03030613
781462209612